Loop Heat Pipe Startup Behaviors

Ku, Jentung

Home/Archive/NASA NTRS

NASA NTRS · 20160008955

Loop Heat Pipe Startup Behaviors

Ku, Jentung

View original source ↗Export metadata ↓

Abstract

A loop heat pipe must start successfully before it can commence its service. The startup transient represents one of the most complex phenomena in the loop heat pipe operation. This paper discusses various aspects of loop heat pipe startup behaviors. Topics include the four startup scenarios, the initial fluid distribution between the evaporator and reservoir that determines the startup scenario, factors that affect the fluid distribution between the evaporator and reservoir, difficulties encountered during the low power startup, and methods to enhance the startup success. Also addressed are the pressure spike and pressure surge during the startup transient, and repeated cycles of loop startup and shutdown under certain conditions.

Explore related subjects

Thermal Control Systems Loop Heat Pipes

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

Ku, Jentung. 2016-07-10. Loop Heat Pipe Startup Behaviors. https://ntrs.nasa.gov/citations/20160008955

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

NASA NTRS2018

Developing a Foundation for Space-Based Two-Phase Thermal Control Systems: Future of 2-Phase Thermal Control

Two-phase thermal control systems in microgravity, with significant density differences between phases, pose challenges for many current and proposed spacecraft systems. Because of the lack of understanding of these effects and the inability to scale multiphase systems in low gravity, NASA generally opts to avoid using two-phase systems for spacecraft despite the significant performance increases and lower mass. The goal of this panel discussion will be to identify key technology gaps and challenges that thermal engineers face today when considering a two-phase thermal management system. The panel discussion will begin with a brief overview of recent and on-going NASA projects designed to elicit a fundamental understanding of gas-liquid two phase behavior as it applies to thermal control systems in the Space environment. The projects/experiments discussed will range from boiling/condensation fundamentals, heat pipes, and cryogenic storage systems. We will identify what fundamental question or questions are being addressed in each case. An overview will be also be presented to address future mission needs and the specific advantages multi-phase systems offer, in particular for low cost planetary science missions and enabling missions in extreme environments. The need for efficient heat transfer with concurrent spatial and temporal temperature stability to reduce thermally-induced noise drives a serious look at multi-phase systems as a solution. Furthermore, missions to environments such as the Venus surface or penetration of ice layers in ocean worlds will likely require them. Time will be allocated at the end of this session to allow comments and questions from attendees. The intent is to use this session as a starting point to advocate for a coordinated technology development effort in this area.

Thermal Control Systems↗

NASA NTRS2018

Experimental Investigation of Heat Pipe Startup Under Reflux Mode

In the absence of body forces such as gravity, a heat pipe will start as soon as its evaporator temperature reaches the saturation temperature. If the heat pipe operates under a reflux mode in ground testing, the liquid puddle will fill the entire cross sectional area of the evaporator. Under this condition, the heat pipe may not start when the evaporator temperature reaches the saturation temperature. Instead, a superheat is required in order for the liquid to vaporize through nucleate boiling. The amount of superheat depends on several factors such as the roughness of the heat pipe internal surface and the gravity head. This paper describes an experimental investigation of the effect of gravity pressure head on the startup of a heat pipe under reflux mode. In this study, a heat pipe with internal axial grooves was placed in a vertical position with different tilt angles relative to the horizontal plane. Heat was applied to the evaporator at the bottom and cooling was provided to the condenser at the top. The liquid-flooded evaporator was divided into seven segments along the axial direction, and an electrical heater was attached to each evaporator segment. Heat was applied to individual heaters in various combinations and sequences. Other test variables included the condenser sink temperature and tilt angle. Test results show that as long as an individual evaporator segment was flooded with liquid initially, a superheat was required to vaporize the liquid in that segment. The amount of superheat required for liquid vaporization was a function of gravity pressure head imposed on that evaporator segment and the initial temperature of the heat pipe. The most efficient and effective way to start the heat pipe was to apply a heat load with a high heat flux to the lowest segment of the evaporator.

Thermal Control Systems↗

NASA NTRS2016

Thermal Vacuum Testing of a Helium Loop Heat Pipe for Large Area Cryocooling

Future NASA space telescopes and exploration missions require cryocooling of large areas such as optics, detector arrays, and cryogenic propellant tanks. One device that can potentially be used to provide closed-loop cryocooling is the cryogenic loop heat pipe (CLHP). A CLHP has many advantages over other devices in terms of reduced mass, reduced vibration, high reliability, and long life. A helium CLHP has been tested extensively in a thermal vacuum chamber using a cryocooler as the heat sink to characterize its transient and steady performance and to verify its ability to cool large areas or components in the 3 degrees Kelvin temperature range. The helium CLHP thermal performance test included cool-down from the ambient temperature, startup, capillary limit, heat removal capability, rapid power changes, and long duration steady state operation. The helium CLHP demonstrated robust operation under steady state and transient conditions. The loop could be cooled from the ambient temperature to subcritical temperatures very effectively, and could start successfully by simply applying power to both the capillary pump and the evaporator plate without pre-conditioning. It could adapt to a rapid heat load change and quickly reach a new steady state. Heat removal between 10 megawatts and 140 megawatts was demonstrated, yielding a power turn down ratio of 14. When the CLHP capillary limit was exceeded, the loop could resume its normal function by reducing the power to the capillary pump. Steady state operations up to 17 hours at several heat loads were demonstrated. The ability of the helium CLHP to cool large areas was therefore successfully verified.

Thermal Control Systems↗