Engineering Papers⌕ Search

Engineering topics

Thermal systems

Find NASA NTRS and DOE OSTI research on heat transfer and thermal systems. Search heat pipes, cooling and thermal management in report titles and abstracts.

Follow this topic with RSS
At least 1,585 records · Page 88
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Validation and Sensitivity Analyses of Arc-Jet Performance of Woven Thermal Protection Entry Systems

A material response model is developed for the determination of erosion rates and thermal response of woven materials to enable accurate thermal protection material sizing and future missions to Venus and giant planets. The stagnation-point thermal response is further evaluated using a Monte Carlo global sensitivity analysis to determine the interactions between key parameters in the material surface energy balance, such as, convective blowing correction parameter and weave material properties including isotropic and orthotropic thermal conductivites. The time-accurate material response for the dual layer weave erosion and surface temperatures show excellent agreement with stagnation flat face arc-jet tests involving time-varying aeroheating-cooling cycles. The high-fidelity Monte Carlo sensitivity analysis technique was used to address challenges in thermal protection sizing for the Adaptive Deployable Entry and Placement Technology (ADEPT) system, a low ballistic coefficient hypersonic decelerator. The results represent new correlations for such weaves involving Carbon-air oxidation equilibrium chemistry. Through the multi-variate regression analyses and uncertainty rankings performed, only three properties were found to contribute to the transient thermal response of the gore, with emissivity contributing to nearly 95% of the total output uncertainty.

Pratibha Raghunandan↗
NASA NTRS2021

Validation and Sensitivity Analyses of Arc-Jet Performance of Woven Thermal Protection Entry Systems

A material response model is developed for the determination of erosion rates and thermal response of woven materials to enable accurate thermal protection material sizing and future missions to Venus and giant planets. The stagnation-point thermal response is further evaluated using a Monte Carlo global sensitivity analysis to determine the interactions between key parameters in the material surface energy balance, such as, convective blowing correction parameter and weave material properties including isotropic and orthotropic thermal conductivites. The time-accurate material response for the dual layer weave erosion and surface temperatures show excellent agreement with stagnation flat face arc-jet tests involving time-varying aeroheating-cooling cycles. The high-fidelity Monte Carlo sensitivity analysis technique was used to address challenges in thermal protection sizing for the Adaptive Deployable Entry and Placement Technology (ADEPT) system, a low ballistic coefficient hypersonic decelerator. The results represent new correlations for such weaves involving Carbon-air oxidation equilibrium chemistry. Through the multi-variate regression analyses and uncertainty rankings performed, only three properties were found to contribute to the transient thermal response of the gore, with emissivity contributing to nearly 95% of the total output uncertainty.

Pratibha Raghunandan↗
NASA NTRSDate not supplied

Additive Manufacture of Porous Zirconium Carbide for Nuclear Thermal Propulsion In-Core Insulators

Nuclear Thermal Propulsion (NTP) requires the use of in-core insulators to manage to thermal environment between high temperature fuel elements and lower temperature structural components. The unforgiving in-core operating conditions severely limit potential material candidates. Zirconium Carbide (ZrC) is a promising candidate due to a high melting temperature, high compressive strength, hardness, wear resistance, hydrogen compatibility, and low neutron absorption cross sections. However, fully dense ZrC is not an insulator but it has been found that the thermal conductivity of ZrC decreases by increasing porosity to approximately 60 % theoretical density (%TD). Previous methods for generating porous ZrC were difficult, expensive, and time consuming. Binder jet additive manufacture (AM) can print ceramic materials to near net shape. Binder jet AM is not utilized in many applications due to an inherently low post-sintering density on the order of 60 %TD. For this specific application the inherent lower density is leveraged as an advantage in production porous ZrC in order to control the thermal conductivity. A feasibility study was conducted to investigate binder jet AM parameter development for ZrC, heat treatment optimization (burn-out and sinter), microstructural characterization, mechanical testing, and thermal testing to generate near-net shape ZrC components with ~60 %TD with the desired thermal conductivity and mechanical strength.

Zirconium Carbide Additive Manufacture↗
NASA NTRSDate not supplied

Additive Manufacture of Porous Zirconium Carbide for Nuclear Thermal Propulsion In-Core Insulators

Nuclear Thermal Propulsion (NTP) requires the use of in-core insulators to manage to thermal environment between high temperature fuel elements and lower temperature structural components. The unforgiving in-core operating conditions severely limit potential material candidates. Zirconium Carbide (ZrC) is a promising candidate due to a high melting temperature, high compressive strength, hardness, wear resistance, hydrogen compatibility, and low neutron absorption cross sections. However, fully dense ZrC is not an insulator but it has been found that the thermal conductivity of ZrC decreases by increasing porosity to approximately 60 % theoretical density (%TD). Previous methods for generating porous ZrC were difficult, expensive, and time consuming. Binder jet additive manufacture (AM) can print ceramic materials to near net shape. Binder jet AM is not utilized in many applications due to an inherently low post-sintering density on the order of 60 %TD. For this specific application the inherent lower density is leveraged as an advantage in production porous ZrC in order to control the thermal conductivity. A feasibility study was conducted to investigate binder jet AM parameter development for ZrC, heat treatment optimization (burn-out and sinter), microstructural characterization, mechanical testing, and thermal testing to generate near-net shape ZrC components with ~60 %TD with the desired thermal conductivity and mechanical strength.

Zirconium Carbide Additive Manufacture↗
NASA NTRSDate not supplied

Evaluation of Coatings for the Electrodynamic Dust Shield Application on Thermal Radiators

Dust acts as a blackbody, becoming hot if left in direct sunlight. This is a problem for thermal radiators where the main function is to radiate heat away from an object. If dust lands on the thermal radiator, the unit will less effectively reject heat, and it will overheat. This can lead to electrical or system failure. The current state-of-the-art in active dust mitigation is the Electrodynamic Dust Shield (EDS) which uses an electric field generated by alternating high positive and negative voltages (low current) to eject the charged dust off surfaces. An EDS made from copper coated Kapton is an ideal candidate to be bonded to a thermal radiator and coated with a low solar absorptance, high heat-emitter coating. This work compares the dust removal of copper-Kapton EDSs covered with different thermal radiator coatings in air and vacuum environments. The coatings include AZ-93 paint, Thermal Bright, and Solar White, a coating developed by the Applied Physics Lab (APL) at NASA Kennedy Space Center (KSC). The resistance and the thickness of the various coatings impact how well it works as an insulative layer for the EDS. Preliminary results indicate that Solar White may have better properties for dust removal and thermal rejection than the other coatings.

Krystal L Acosta↗
NASA NTRS2022

Updraft Dynamics and Microphysics: On the Added Value of the Cumulus Thermal Reference Frame in Simulations of Aerosol–Deep Convection Interactions

One fundamental question about atmospheric moist convection processes that remains debated is whether or under what conditions a relevant variability in background aerosol concentrations may have a significant dynamical impact on convective clouds and their associated precipitation. Furthermore, current climate models must parameterize both the microphysical and the cumulus convection processes, but this is usually implemented separately, whereas in nature there is a strong coupling between them. As a first step to improve our understanding of these two problems, we investigate how aerosol concentrations modify key properties of updrafts in eight large-eddy permitting regional simulations of a case study of scattered convection over Houston, Texas, in which convection is explicitly simulated and microphysical processes are parameterized. Dynamical and liquid-phase microphysical responses are investigated using two different reference frames: static cloudy-updraft grid cells versus tracked cumulus thermals. In both frameworks we observe the expected microphysical responses to higher aerosol concentrations, such as higher cloud number concentrations and lower rain number concentrations. In terms of the dynamical responses, both frameworks indicate weak impacts of varying aerosol concentrations relative to the noise between simulations over the observationally derived range of aerosol variability for this case study. On the other hand, results suggest that thermals are more selective than cloudy-updraft grid cells in terms of sampling the most active convective air masses. For instance, vertical velocity from thermals is significantly higher at upper levels than when sampled from cloudy-updraft grid points, and several microphysical variables have higher average values in the cumulus thermal framework than in the cloudy-updraft framework. In addition, the thermal analysis is seen to add rich quantitative information about the rates and covariability of microphysical processes spatially and throughout tracked thermal lifecycles, which can serve as a stronger foundation for improving subgrid-scale parameterizations.

Daniel Hernandez-Deckers↗
NASA NTRS2021

Europa Environmental Testing of Thermal Hardware for the Mapping Imaging Spectrometer for Europa (MISE) Instrument

The Europa Clipper spacecraft, scheduled for launch in June 2022, hosts a suite of instruments including the Mapping Imaging Spectrometer for Europa (MISE). MISE is a high-optical through-put pushbroom infrared imaging spectrometer that can collect measurements within Europa’s challenging radiation environment. It is externally mounted to the spacecraft and as a result is exposed to high radiation levels and cold temperatures. The instrument consists of a scan mirror assembly, an optical bench including a Dyson spectrometer and a telescope, and a structure that supports a cryocooler and a radiator. The cryocooler is used to actively cool the focal plane array and the spectrometer. The heat from the cryocooler is rejected through pyrolytic graphite sheet thermal straps to a honeycomb radiator. MISE will implement thermal hardware that will either not be used on other parts of the spacecraft or have a more extreme environment than the spacecraft. As a result, the MISE instrument performed numerous environmental tests on its thermal hardware. This paper discusses the results of the thermal cycling and radiation tests performed on the MISE thermal hardware including a Lockheed Martin Micro1-2 cryocooler, Pyrolytic graphite sheet thermal straps, Annealed pyrolytic graphite K-Core, Rosemount Platinum Resistance Thermometers, Tayco Kapton Thermofoil heaters, Dale Ohm resistors, and aluminum honeycomb and facesheets.

Strong, Patrick↗
NASA NTRS2021

Instrument Thermal Management for Lunar Night Survival without Radioisotopes

This paper summarizes the technology development progress on two JPL projects focused on developing thermal designs/technologies that enable lunar instrument overnight survival without radioisotopes. Through an internal project known as ARTEMIS, JPL has developed lunar night survivable designs for magnetometer, seismometer, and IR spectrometer science payloads (SPs). These designs incorporate four hyper-isolative thermal management features under development on the NASA GCD-funded PALETTE project: (a) a dual enclosure system with high strength, low k tension cable (TC) supports and a variable conductance thermal link (VCTL) composed of a reverse-operation DTE thermal switch (ROD-TSW) in series with a miniaturized loop heat pipe (mini-LHP); (b) a parabolic reflector radiator (PRR) for low-to-mid latitude lunar sites; (c) ultra-low e* “spacerless” MLI, in which individual layers are hung from the TC supports; and (d) ultra-low G thermal isolators made with polymeric material or polymer/TC assemblies. Each instrument design incorporates solar panels, batteries, telecom, C&DH, and other features necessary for self-sufficient, extended-duration operation on the lunar surface. This paper will provide an overview of the ARTEMIS and PALETTE projects and provide a top-level description of the instrument thermal management approach.

Lin, Ying↗
NASA NTRS2021

Europa Clipper Magnetometer Thermal Design Evolution, Validation, and Verification

Europa Clipper Spacecraft is exposed to a high radiation environment and is limited with power. This makes the thermal design of Europa Clipper magnetometer more challenging. The design is required to be highly insulated and at the same time magnetically clean. This paper describes the thermal design evolution of Europa Clipper Magnetometer. A thermal vacuum test is conducted in Europa Clipper orbit’s relevant environment to characterize the requirements and estimate the power consumption. A flight-like engineering model magnetometer from the University of California at Los Angeles (UCLA) is used for this test. Magnetically clean Cernox temperature measurement sensors with the accuracy of ±0.1ºC are used to measure the temperature value inside the sensor head and across the main frame interfaces. This level of accuracy in temperature measurement is required to capture the temperature gradient across the sensor head in a relevant environment which impacts the magnetometer measurement accuracy. Test data is used to correlate the thermal model and characterize the heat leak across the interfaces. Validated thermal model is used as a verification tool for power consumption and thermal requirements.

Caron, Ryan↗
NASA NTRS2022

Solar Flare Heating with Turbulent Suppression of Thermal Conduction

During solar flares plasma is typically heated to very high temperatures, and the resulting redistribution of energy via thermal conduction is a primary mechanism transporting energy throughout the flaring solar atmosphere. The thermal flux is usually modeled using Spitzer’s theory, which is based on local Coulomb collisions between the electrons carrying the thermal flux and those in the background. However, often during flares, temperature gradients become sufficiently steep that the collisional mean free path exceeds the temperature gradient scale size, so that thermal conduction becomes inherently non-local. Further, turbulent angular scattering, which is detectable in nonthermal widths of atomic emission lines, can also act to increase the collision frequency and so suppress the heat flux. Recent work by Emslie & Bian (2018) extended Spitzer’s theory of thermal conduction to account for both non-locality and turbulent suppression. We have implemented their theoretical expression for the heat flux (which is a convolution of the Spitzer flux with a kernel function) into the RADYN flare-modeling code and performed a parameter study to understand how the resulting changes in thermal conduction affect flare dynamics and hence the radiation produced. We find that models with reduced heat fluxes predict slower bulk flows, less intense line emission, and longer cooling times. By comparing features of atomic emission lines predicted by the models with Doppler velocities and nonthermal line widths deduced from a particular flare observation, we find that models with suppression factors between 0.3 to 0.5 relative to the Spitzer value best reproduce observed Doppmission lines forming over a wide range of temperatures. Interestingly, the model that best matches observed nonthermal line widths has a kappa-type velocity distribution function.

Joel C. Allred↗
NASA NTRS2022

Solar Flare Heating with Turbulent Suppression of Thermal Conduction

During solar flares plasma is typically heated to very high temperatures, and the resulting redistribution of energy via thermal conduction is a primary mechanism transporting energy throughout the flaring solar atmosphere. The thermal flux is usually modeled using Spitzer’s theory, which is based on local Coulomb collisions between the electrons carrying the thermal flux and those in the background. However, often during flares, temperature gradients become sufficiently steep that the collisional mean free path exceeds the temperature gradient scale size, so that thermal conduction becomes inherently non-local. Further, turbulent angular scattering, which is detectable in nonthermal widths of atomic emission lines, can also act to increase the collision frequency and so suppress the heat flux. Recent work by Emslie & Bian (2018) extended Spitzer’s theory of thermal conduction to account for both non-locality and turbulent suppression. We have implemented their theoretical expression for the heat flux (which is a convolution of the Spitzer flux with a kernel function) into the RADYN flare-modeling code and performed a parameter study to understand how the resulting changes in thermal conduction affect flare dynamics and hence the radiation produced. We find that models with reduced heat fluxes predict slower bulk flows, less intense line emission, and longer cooling times. By comparing features of atomic emission lines predicted by the models with Doppler velocities and nonthermal line widths deduced from a particular flare observation, we find that models with suppression factors between 0.3 to 0.5 relative to the Spitzer value best reproduce observed Doppler velocities across emission lines forming over a wide range of temperatures. Interestingly, the model that best matches observed nonthermal line widths has a kappa-type velocity distribution function

Solar flares↗
NASA NTRS2024

Bringing the Heat: Thermal Protection Systems for Low Earth Orbit Transportation and Lunar Exploration

Thermal protection systems (TPS) protect spacecraft from the heating associated with hypersonic flight through a planet’s atmosphere. The materials are subjected to extreme heating and the overall system must be engineered to reliably protect the spacecraft structure during atmospheric entry. The talk will introduce TPS and describe three NASA-led efforts to develop TPS materials and manufacturing processes. The first effort studied thermally stable ceramic aerogels for use in thermal barriers and high temperature seals. A design framework for such materials is proposed, linking the thermal stability performance data with existing material property measurements. The second project, Additive Manufacturing of Thermal Protection Systems (AMTPS), developed an automated, additive approach for ablative heat shield manufacturing. Novel material systems and manufacturing methods were developed to reduce the time required to manufacture ablative TPS heat shields. The third effort tackles a critical challenge of material obsolescence for silica fiber based reusable TPS. The properties and performance of heritage silica fiber are quantified and compared to modern alternatives to support qualification for flight. The talk will also describe other work in TPS conducted by the Thermal Design Branch at NASA JSC and opportunities for students and faculty to get involved with NASA.

Nathaniel Olson↗
NASA NTRS2026

Investigating Dual Electrospinning as a Means of Enhancing Passive Thermal Control Coatings for Cryogenic Propellant Storage in Extraterrestrial Environments

Passive thermal control is necessary as space exploration becomes increasingly widespread. Materials with superior optical properties (high solar reflectance and infrared emittance) are critical for passive thermal control because they can reject most of the incident solar radiation and promote thermal emission from cryogenic propellant storage tanks, enabling the extraterrestrial storage of cryogens. We have demonstrated in previous studies that electrospun nanofibers exhibit exceptional optical properties, offering significant benefits for passive radiative cooling in space. Particularly, electrospun polyvinylidene fluoride-co-hexafluoropropylene PVDF-HFP nanofibers demonstrate exceptionally high solar reflectance (>99%) and strong thermal emittance (measured at ~300 K). However, they exhibit nanostructural changes in the presence of atomic oxygen, which is prevalent in Low Earth Orbit. This study focuses on creating a unique blend of polymeric (PVDF-HFP) and ceramic-based (silica) nanofibers by leveraging the chemical stability and atomic oxygen resistance of silica, using the dual electrospinning manufacturing method. This approach aims to preserve the structural properties of the polymeric counterpart without compromising its optical performance, thereby providing an innovative method for manufacturing environmentally resilient passive thermal control nanofibers with desirable optical and thermal control functionalities for extraterrestrial storage of cryogenic propellants.

Chieloka Ibekwe↗
NASA NTRS2026

Assessing the Adhesion of Nanofibrous PVDF-HFP as Passive Thermal Control Coatings for the Extraterrestrial Storage of Cryogenic Propellants

Cryogenic propellant passive thermal management techniques in space are essential complements to active thermal management methods, helping reduce absolute dependence on the latter. Particularly, materials with superior optical properties (high solar reflectance and infrared emittance) would be beneficial for passive thermal control to reject most of the incident solar radiation and enhance thermal emission from the storage tank, leading to self-cooling. We developed a nanofibrous, porous passive thermal control material by electrospinning polyvinylidene fluoride-co-hexafluoropropylene (PVDF-HFP) co-polymer onto an aluminum foil substrate. The material exhibits a very high solar reflectance (>99%) and infrared emittance (~86%) when characterized in the ultraviolet-visible-near infrared and mid-infrared wavelengths. This study focuses on the adhesion of the nanofibrous PVDF-HFP to the substrate. We incorporated in-lab fabricated and commercial adhesives, under normal room conditions, between the nanofibers and the aluminum foil substrate to improve their adhesion. Some samples were also exposed to space-like conditions – vacuum and thermal cycling, to investigate their effects on the strengths of adhesives. Subsequently, adhesion peel tests were conducted on all the samples to assess the peel strengths of the bonds. Peel test strengths after space environment conditioning of the adhesives were generally higher than those observed in the pristine, unaged samples. The results are discussed in this study.

Chieloka Ibekwe↗
DOE OSTI2020

Flexible linkages for thermal management at cryogenic temperatures

Cryogenic system design often presents the competing requirements of thermal coupling between components while de-coupling them structurally. Good thermal coupling is necessary for adequate thermal management during cryogenic operation of the system and to reduce the cooldown time from the ambient to cryogenic temperature. Structural de-coupling is essential to reduce thermal stresses during cooldown, mitigate the trasmission of vibration and loads to sensitive and/or fragile components, and compensate for integration misalignments. Flexible thermal links (FTLs) are an essential component of cryogenic systems that provides a balance between thermal coupling and structural isolation.

42 ENGINEERING↗
DOE OSTI2022

Thermal barrier coatings for internal combustion engines

A thermal barrier coating for an internal combustion engine includes an insulating thermal spray coating, where a chosen material of the insulating thermal spray coating has a thermal conductivity lower than 2 W/mK in fully dense form and the chosen material includes a coefficient of thermal expansion within 5 ppm/K of a coefficient of thermal expansion of a material of a component of the internal combustion engine upon which the coating is placed.

Jordan, Eric↗
DOE OSTI2021

Probing Microstructure-induced Swelling & Thermal Property Changes in Ion-Irradiated Oxide Fuels using Laser-generated Surface Acoustic Waves

Radiation of fuel rods with neutrons during a fission reaction in a nuclear reactor is known to affect the material microstructure of the fuel as a result of fission fragment damage, and lead to the formation of atomic-level defects such as voids, dislocation loops, and lattice swelling from fission-gas release. A consequence of the radiation-induced damage in nuclear fuels is the drastic alteration of material properties, in particular, the reduction of the thermal conductivity – a key parameter that governs the transport of thermal energy released from fissile fuel atoms to the surrounding coolant. Swelling can induce high stresses and ultimate failure of the cladding. A fundamental understanding of the role of radiation-induced damage on the thermal transport and mechanical properties of nuclear fuels is therefore critical for efficient, reliable and safe operation of a nuclear power plant. As opposed to conventional post-irradiation examination techniques that are often time-consuming and require significant sample preparation, laser-based characterization methods have emerged as promising non-contact, non-destructive tools to measure the evolution of microstructure-induced material property changes. Moreover, laser methods offer the promise of in-situ characterization while the material is being irradiated. This project aims to develop an improved understanding of the impact of radiation-induced changes to material microstructure on the thermal and elastic properties of nuclear materials. A laser ultrasonic technique, known as the transient grating (TG) spectroscopy method, is used to simultaneously measure thermal diffusivity and elastic properties in unirradiated and ion-irradiated oxide nuclear fuel samples. The results will complement on-going investigations on electron- and phonon-mediated thermal transport in nuclear materials and will provide foundational work for incorporating the influence of defects in fuel performance codes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Thermal barrier coatings for internal combustion engines

A thermal barrier coating for an internal combustion engine includes an insulating thermal spray coating, where a chosen material of the insulating thermal spray coating has a thermal conductivity lower than 2 W/mK in fully dense form and the chosen material includes a coefficient of thermal expansion within 5 ppm/K of a coefficient of thermal expansion of a material of a component of the internal combustion engine upon which the coating is placed.

Jordan, Eric↗