Engineering Papers⌕ Search

Engineering topics

Propulsion

Explore propulsion reports from NASA NTRS and DOE OSTI. Search rocket engines, electric propulsion and thrusters; verify designs and performance in the source documents.

Follow this topic with RSS
At least 1,459 records · Page 81
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Optical Measurements on Solid Specimens of Solid Rocket Motor Exhaust and Solid Rocket Motor Slag

Samples of aluminum slag were investigated to aid the Earth Science and Applications Division at the Marshall Space Flight Center (MSFC). Alumina from space motor propellant exhaust and space motor propellant slag was examined as a component of space refuse. Thermal emittance and solar absorptivity measurements were taken to support their comparison with reflectance measurements derived from actual debris. To determine the similarity between the samples and space motor exhaust or space motor slag, emittance and absorbance results were correlated with an examination of specimen morphology.

Roberts, F. E., III↗
NASA NTRS1992

Advanced small rocket chambers: Option 1, 14 lbf Ir-Re rocket

A high performance Ir-Re 14 lbf (62 N) chamber and nozzle which can be a direct replacement for a production engine was designed, built, hot fired and vibration acceptance tested. It passed all acceptance tests satisfactorily and demonstrated a 20 sec increase in specific impulse (Is) over the conventional 14 lbf silicide coated Cb chamber. The high performance engine uses the production valve and injector without modification. Incorporation of a secondary mixing device or Boundary Layer Trip within the combustion chamber results in elimination of the fuel film coolant, improvement in flow uniformity, the 20 sec performance increase, and reduction of a potential source of spacecraft contamination. Measured Is was 305 sec at 75:1 area ratio, with monomenthylhydrazine and nitrogen tetroxide propellants. Qualification tests remain to be done.

Jassowski, Donald M.↗
NASA NTRS1993

An RL10A-3-3A rocket engine model using the Rocket Engine Transient Simulator (ROCETS) software

The RL10 engine is a critical component of past, present, and future space missions. The paper discusses the RL10A-3-3A engine system and its model created using the ROCETS computer code. The simulation model will give NASA an in-house capability to simulate the performance of the engine under various operating conditions and mission profiles. A comparison of steady-state model predictions with test-stand data is presented together with a comparison of predicted start transient behavior with flight data.

Binder, Michael↗
NASA NTRS1966

Radiation from Rocket Exhaust Plumes: Inhomogeneous Radiant Heat Transfer from Saturn Type Rocket Exhaust Plumes - Part 1

A radiant heat transfer computer program has been developed by R-AERO-A to calculate radiation from inhomogeneous gases prevalent in Saturn-type exhaust plumes. The radiating species considered in this computer program are water vapor, carbon dioxide, carbon monoxide and carbon particles. The infrared spectral absorption characteristics of these species have been determined under NASA contract. Band model parameters have been used to represent the infrared spectral absorption coefficients over 25 cm-I increments. A modified Curtis-Goodson approximation is used in the inhomogeneous heat transfer calculation. This has been shown to give satisfactory results over the temperature and pressure range of interest in Saturn exhaust plumes. Results are shown for the Saturn-type engines for specific flow field assumptions. Some comparison with experimental spectroscopic data will also be presented. The effect of wavelength increment, field of view, and distance increment along the line of sight on the heat transfer will be discussed. Computer techniques for minimum computer time in calculating radiation from a three-dimensional flow field will also be outlined.

Huffaker, Robert M.↗
NASA NTRS2015

Revised Point of Departure Design Options for Nuclear Thermal Propulsion

Four Revised Point of Departure NTR Engines were Designed and Analyzed using MCNP and NESS. All Four Engines Have Thermodynamically Closed Cycles at Nominal Chamber Pressures. 111 kilonewton (25 kip-force) Cermet Design Required Dedicated Heater Elements to Close the Cycle. Cermet Based Designs had Slightly Higher TW Ratios, but Required Substantially More U-235. NERVA Derived Criticality Limited Engine Could Operate at Lower Power and Thrust Levels Compared to the Criticality Limited Cermet Design.

Nuclear Thermal Rocket↗
NASA NTRSDate not supplied

Additive Manufacturing for Propulsion Applications

This event will improve MSFC team members’ understanding and awareness of Agency strategy related to advanced manufacturing subjects. With a focus toward growing Engineering Directorate knowledge of the selected topics, Subject Matter Experts will provide lectures on the technologies that MSFC will need to leverage in order successfully achieve new objectives related to our role in On-Orbit-Servicing, Assembly, and Manufacturing (OSAM) and provide updates on Center Initiatives. The workshop will conclude with a panel discussion including MSFC leaders from discipline and project formulation offices with conversations related to innovative technologies.

Additive Manufacturing↗