Engineering topics

Materials science

Explore NASA and DOE materials research. Search alloys, composites and material properties, then open the original technical report for test conditions and results.

Follow this topic with RSS

At least 1,693 records · Page 94

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Thin film combinatorial sputtering of Al-Ce alloys: Investigating the phase separation of as-deposited solid solutions and determining the coefficient of thermal expansion

Al x Ce 100–x thin films with a composition range of ~75.0 < x < 99.5 at% (36.5 < x < 97.5 wt%) were synthesized via combinatorial co-sputtering from an Al and an Al 50 Ce 50 target. The crystal structure, phase fraction, film morphology, electrical resistivity, and temperature-dependent coefficients of thermal expansion (CTE) are all correlated to the Al x Ce 100–x composition. The as-deposited films form a metastable solid-solution, and annealing leads to the formation of the thermodynamically stable two-phase system of Al and the α-Al 11 Ce 3 intermetallic. Temperature dependent x-ray diffraction (XRD) reveals that the two phases expand independently of one another, and the thin film Al temperature-dependent CTE is similar to bulk Al. The thin film Al 11 Ce 3 intermetallic phase has a nearly constant CTE of ~1.5 × 10 –5 /°C within the temperature range studied (25–550 °C). To confirm the thin film Al 11 Ce 3 results, bulk stoichiometric Al 11 Ce 3 and +/- 1 wt% Ce samples were prepared and the CTE of each was measured with the same conditions. A Rietveld analysis of the bulk data enabled an estimation of the CTE in each of the 3 orthorhombic lattice parameters, which displayed anisotropic behavior. The thin film and bulk CTE measurements were in very good agreement. Estimations of the temperature dependent CTE of the two-phase alloys are made via the Reuss and Voigt models. Finally, by demonstrating the efficacy of the approach, more complex multi-component rapid materials discovery of low CTE Al-alloys can be pursued via the combinatorial thin film synthesis and XRD measurement.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Effects of transient thermal shock on the microstructures and corrosion properties of a reduced activation high-entropy alloy

The devices would subject transient thermal shocks (TTS) during operation under extremely harsh conditions of nuclear fusion reactors, which inevitably exert significant impact on the microstructure and performance of structural materials. Here, a reduced activation VCrFeTa 0.2 W 0.2 high-entropy alloy (HEA) was developed by vacuum arc melting. The effects of electron beam induced TTS on its microstructure, microhardness, and corrosion properties were investigated. The results indicate that the weight fraction of each phase changes after TTS, showing a significant decrease in the content of BCC1 phase and an increase in the content of BCC2 and Laves phases. The content of BCC1 phase continues to decrease slightly with increasing the power of TTS. Besides, the microhardness of the alloy increases from ~673 HV to ~714 HV after TTS treatments. In the reduced activation HEA, TTS results in a relatively low corrosion current density of ~0.472 μA/cm 2 in 3.5 wt% NaCl solution, around one-third of the current density observed in the as-cast sample. Furthermore, the VCrFeTa 0.2 W 0.2 HEA after TTS exhibits a pitting potential of ~1.165 V SCE , which is much higher than that of the as-cast sample. The refined composite multiscale entropy method is employed to analyze the influence of TTS on current fluctuation behavior during the corrosion process. The reduced activation VCrFeTa 0.2 W 0.2 HEA exhibits excellent properties in harsh environments after TTS, thereby showing advantageous property in the field of nuclear structural materials. Furthermore, TTS is an efficient and controllable strategy for the improvement of the HEAs’ microstructures and performances.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Modeling antiphase boundary energies of Ni 3 Al-based alloys using automated density functional theory and machine learning

Antiphase boundaries (APBs) are planar defects that play a critical role in strengthening Ni-based superalloys, and their sensitivity to alloy composition offers a flexible tuning parameter for alloy design. Here, we report a computational workflow to enable the development of sufficient data to train machine-learning (ML) models to automate the study of the effect of composition on the (111) APB energy in Ni 3 Al-based alloys. We employ ML to leverage this wealth of data and identify several physical properties that are used to build predictive models for the APB energy that achieve a cross-validation error of 0.033 J m –2 . We demonstrate the transferability of these models by predicting APB energies in commercial superalloys. Moreover, our use of physically motivated features such as the ordering energy and stoichiometry-based features opens the way to using existing materials properties databases to guide superalloy design strategies to maximize the APB energy.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Lightweight High-Temperature Alloys Based on the AlFeSi System

Automotive applications need low-cost, lightweight, high-temperature alloys to enhance efficiencies in systems such as internal combustion engines. The aluminum-iron-silicon (Al-Fe-Si) system provides an opportunity to develop such a material, as it comprises three of the lowest cost elements abundant in nature. Specifically, the $τ_{11}$-Al 4 Fe 1.7 Si (historically called $τ_{10}$) ternary intermetallic phase is a lightweight and low-cost phase with promising mechanical properties at high temperatures. However, the $τ_{11}$-Al 4 Fe 1.7 Si phase has a narrow compositional range, which should be expanded to use this alloy at a commercial scale. To increase this compositional range, equilibrium phase boundaries were expanded using alloy design strategies.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Phase diagram of magnetic shape memory alloy Ni 50 Mn $50–x$ In $x$ , 0 < $x$ , 25 from first principles, via spin cluster expansion and phonon vibrational entropies

The metamagnetic shape memory Heusler alloy Ni 50 Mn $50–x$ In $x$ exhibits a rich phase diagram featuring competing magnetic states, coupled magnetic–structural phase transitions, and strong compositional sensitivity. Existing first-principles approaches struggletocapturetheintertwinedchemical, magnetic, andvibrationaleffectsinthesealloys, necessitating a more integrated modeling framework. We develop a spin cluster expansion (spin-CE) framework augmented by a quasi-harmonic phonon model to capture both configurational (chemical and magnetic) and vibrational contributions to the free energy of Ni 50 Mn $50–x$ In $x$ over the full compositional range 0 ≤ x ≤25. The spin-CE includes both chemical clusters and composition-dependent Ising spin interactions, with parameters fit to a first-principles density functional theory (DFT) dataset. Using this approach, we predict the complete magnetostructural phase diagram and transformation temperatures of Ni 50 Mn $50–x$ In $x$ across the composition space. We find that vibrational entropy alone is insufficient to reproduce the martensitic transformation in the magnetic shape memory alloy regime, highlighting the essential role of magnetism. Incorporating both magnetic and vibrational contributions allows us to reproduce all experimentally known phases, including the disappearance of the stable martensite phase at a critical In concentration and the Curie temperature of the austenite phase. The method also captures the transition with increasing In in martensite from antiferromagnetic to ferromagnetic order and predicts re-entrant ferromagnetism, though the latter occurs at higher In content than reported experimentally. We discuss possible sources of this discrepancy and highlight the broader applicability of the method to other magnetostructurally complex materials, where it may offer mechanistic insight and predictive design capabilities.

Cluster expansion↗

DOE OSTI2024

High Temperature Mechanical Behavior of Refractory Alloys with Digital Image Correlation

Gas turbine efficiency is typically limited by the maximum allowable temperature for components at the inlet side and in the hot gas flow. Refractory alloys and SiC/SiC ceramic-matrix composites (CMCs) are promising candidates for advancing operating temperatures beyond those of Ni-based alloys (>1200 °C). Refractory alloys are more suitable than SiC/SiC CMCs for dynamic components, due to the latter's low toughness and ductility. However, it is well known that refractory alloys suffer from poor oxidation behavior under service lifetimes and conditions, leading to embrittlement concerns. The ARPA-E ULTIMATE program has set out to combine new alloys with advanced coatings to mitigate oxidation/embrittlement effects, while increasing the mechanical performance benefits of refractory materials. Low oxygen (inert gas) or vacuum systems are needed to assess high temperature mechanical performance of developed alloys. To investigate the environmental sensitivity of candidate alloys and develop high temperature testing capabilities, four argon tensile frames were upgraded as well as a single vacuum system at Oak Ridge National Laboratory. Digital image correlation was incorporated into the vacuum frame allowing for surface strain determination and refined insight into thermomechanical response. Creep testing was performed at 1300 °C on two alloys, C-103 and MHC in vacuum and high purity argon environments. The Mo-based alloy showed less sensitivity to oxygen, indicating that testing in well-controlled argon environments may be suitable. The C-103 alloy demonstrated a stronger sensitivity to oxygen in the well-controlled argon environment, illustrating the need for the developed vacuum testing capabilities. “Small” 25 mm and “large” 76 mm MHC specimens showed comparable results in terms of strain rate during creep testing and ultimate tensile strength during tensile testing, suggesting the viability of smaller geometries that use less material of advanced developmental alloys.

Bell, Sam↗

NASA NTRS1993

Solidification of eutectic system alloys in space (M-19)

It is well known that in the liquid state eutectic alloys are theoretically homogeneous under 1 g conditions. However, the homogeneous solidified structure of this alloy is not obtained because thermal convection and non-equilibrium solidification occur. The present investigators have clarified the solidification mechanisms of the eutectic system alloys under 1 g conditions by using the in situ observation method; in particular, the primary crystals of the eutectic system alloys never nucleated in the liquid, but instead did so on the mold wall, and the crystals separated from the mold wall by fluid motion caused by thermal convection. They also found that the equiaxed eutectic grains (eutectic cells) are formed on the primary crystals. In this case, the leading phase of the eutectic must agree with the phase of the primary crystals. In space, no thermal convection occurs so that primary crystals should not move from the mold wall and should not appear inside the solidified structure. Therefore no equiaxed eutectic grains will be formed under microgravity conditions. Past space experiments concerning eutectic alloys were classified into two types of experiments: one with respect to the solidification mechanisms of the eutectic alloys and the other to the unidirectional solidification of this alloy. The former type of experiment has the problem that the solidified structures between microgravity and 1 g conditions show little difference. This is why the flight samples were prepared by the ordinary cast techniques on Earth. Therefore it is impossible to ascertain whether or not the nucleation and growth of primary crystals in the melt occur and if primary crystals influence the formation of the equiaxed eutectic grains. In this experiment, hypo- and hyper-eutectic aluminum copper alloys which are near eutectic point are used. The chemical compositions of the samples are Al-32.4mass%Cu (Hypo-eutectic) and Al-33.5mass%Cu (hyper-eutectic). Long rods for the samples are cast by the Ohno Continuous Casting Process and they show the unidirectionally solidified structure. Each flight and ground sample was made of these same rods. The dimensions of all samples are 4.5 mm in diameter and 23.5 mm in length. Each sample is put in a graphite capsule and then vacuum sealed in a double silica ampoule. Then the ampoule is put in the tantalum cartridge and sealed by electron beam welding. For onbard experiments, a Continuous Heating Furnance (CHF) will be used for melting and solidifying samples under microgravity conditions. Six flight samples will be used. Four samples are hypo-eutectic and two are hyper-eutectic alloys. The surface of the two hypo-eutectic alloy samples are covered with aluminum oxide film to prevent Marangoni convection expected under microgravity conditions. Each sample will be heated to 700 C and held at that temperature for 5 min. After that the samples will be allowed to cool to 500 C in the furnace and they will be taken out of the furnace for He gas cooling. The heating and cooling diagrams for the flight experiments are shown. After collecting the flight samples, the solidified structures of the samples will be examined and the mechanisms of eutectic solidification under microgravity conditions will be determined. It is likely that successful flight experiment results will lead to production of high quality eutectic alloys and eutectic composite materials in space.

Ohno, Atsumi↗

NASA NTRS2003

Characterization of Al-Cu-Mg-Ag Alloy RX226-T8 Plate

Aluminum-copper-magnesium-silver (Al-Cu-Mg-Ag) alloys that were developed for thermal stability also offer attractive ambient temperature strength-toughness combinations, and therefore, can be considered for a broad range of airframe structural applications. The current study evaluated Al-Cu-Mg-Ag alloy RX226-T8 in plate gages and compared performance with sheet gage alloys of similar composition. Uniaxial tensile properties, plane strain initiation fracture toughness, and plane stress tearing resistance of RX226-T8 were examined at ambient temperature as a function of orientation and thickness location in the plate. Properties were measured near the surface and at the mid-plane of the plate. Tensile strengths were essentially isotropic, with variations in yield and ultimate tensile strengths of less than 2% as a function of orientation and through-thickness location. However, ductility varied by more than 15% with orientation. Fracture toughness was generally higher at the mid-plane and greater for the L-T orientation, although the differences were small near the surface of the plate. Metallurgical analysis indicated that the microstructure was primarily recrystallized with weak texture and was uniform through the plate with the exception of a fine-grained layer near the surface of the plate. Scanning electron microscope analysis revealed Al-Cu-Mg second phase particles which varied in composition and were primarily located on grain boundaries parallel to the rolling direction. Fractography of toughness specimens for both plate locations and orientations revealed that fracture occurred predominantly by transgranular microvoid coalescence. Introduction High-strength, low-density Al-Cu-Mg-Ag alloys were initially developed to replace conventional 2000 (Al-Cu-Mg) and 7000 (Al-Zn-Cu-Mg) series aluminum alloys for aircraft structural applications [1]. During the High Speed Civil Transport (HSCT) program, improvements in thermal stability were demonstrated for candidate aircraft wing and fuselage skin materials through the addition of silver to Al-Cu-Mg alloys based on Al 2519 chemistry [2]. Thermal stability of the resulting Al-Cu-Mg-Ag alloys, C415-T8 and C416-T8, was due to co-precipitation of the thermally stable . (AlCu) and ' (Al2Cu) strengthening phases [1-4]. The strength and toughness behavior was investigated for these alloys produced as 0.090-inch thick rolled sheet in the T8 condition and after various thermal exposures. The mechanical properties were shown to be competitive with conventional aircraft alloys, 2519-T8 and 2618-T8 [2]. During the Integral Airframe Structure (IAS) program, advanced aluminum alloys were examined for use in an integrally stiffened airframe structure where the skin and stiffeners would be machined from plate and extruded frames would be mechanically attached (see Figure 1) [5]. Advantages of integrally stiffened structure include reduced part count, and reduced assembly times compared to conventional built-up airframe structure. The near-surface properties of a thick plate are of significance for a machined integrally stiffened airframe structure since this represents the skin location. Properties measured at the mid-plane of the plate are more representative of the stiffener web. RX226 was developed to exploit strength-toughness improvements and thermal stability benefits of Al-Cu-Mg-Ag alloys in plate gages. This study evaluated the microstructure and properties of three gages of plate produced in the T8 condition.

Lach, Cynthia L.↗

NASA NTRS2007

Development of Multifunctional Radiation Shielding Materials for Long Duration Human Exploration Beyond the Low Earth Orbit

One of the major challenges for long duration human exploration beyond the low Earth orbit and sustained human presence on planetary surfaces would be development of materials that would help minimize the radiation exposure to crew and equipment from the interplanetary radiation environment, This radiation environment consists primarily of a continuous flux of galactic cosmic rays (GCR) and transient but intense fluxes of solar energetic particles (SEP). The potential for biological damage by the relatively low percentage of high-energy heavy-ions in the GCR spectrum far outweigh that due to lighter particles because of their ionizing-power and the quality of the resulting biological damage. Although the SEP spectrum does not contain heavy ions and their energy range is much lower than that for GCRs, they however pose serious risks to astronaut health particularly in the event of a bad solar storm The primary purpose of this paper is to discuss our recent efforts in development and evaluation of materials for minimizing the hazards from the interplanetary radiation environment. Traditionally, addition of shielding materials to spacecrafts has invariably resulted in paying a penalty in terms of additional weight. It would therefore be of great benefit if materials could be developed not only with superior shielding effectiveness but also sufficient structural integrity. Such a multifunctional material could then be considered as an integral part of spacecraft structures. Any proposed radiation shielding material for use in outer space should be composed of nuclei that maximize the likelihood of projectile fragmentation while producing the minimum number of target fragments. A modeling based approach will be presented to show that composite materials using hydrogen-rich epoxy matrices reinforced with polyethylene fibers and/or fabrics could effectively meet this requirement. This paper will discuss the fabrication of such a material for a crewed vehicle. Ln addition, the capability of synthesizing radiation shielding materials for habitat structures primarily from Lunar or Martian in-situ resources will also be presented. Such an approach would significantly _reduce the cost associated with transportation of such materials and structures from earth. Results from radiation exposure measurements will be presented demonstrating the shielding effectiveness of the developed materials. Mechanical testing data will be discussed to illustrate that the specific mechanical properties of the developed composites are comparable to structural aluminum based alloys currently used for the space shuttle and space station.

Sen, S.↗

DOE OSTI2021

High-throughput design of high-performance lightweight high-entropy alloys

Developing affordable and light high-temperature materials alternative to Ni-base superalloys has significantly increased the efforts in designing advanced ferritic superalloys. However, currently developed ferritic superalloys still exhibit low high-temperature strengths, which limits their usage. Here we use a CALPHAD-based high-throughput computational method to design light, strong, and low-cost high-entropy alloys for elevated-temperature applications. Through the high-throughput screening, precipitation-strengthened lightweight high-entropy alloys are discovered from thousands of initial compositions, which exhibit enhanced strengths compared to other counterparts at room and elevated temperatures. The experimental and theoretical understanding of both successful and failed cases in their strengthening mechanisms and order-disorder transitions further improves the accuracy of the thermodynamic database of the discovered alloy system. This study shows that integrating high-throughput screening, multiscale modeling, and experimental validation proves to be efficient and useful in accelerating the discovery of advanced precipitation-strengthened structural materials tuned by the high-entropy alloy concept.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Dynamic re-equilibration controlled multi-step transformations in (Mn, Fe) 2 (P, Si) alloys

In (Mn, Fe) 2 (P, Si) alloys crystallographic first-order phase transformations enable strong coupling of magnetic and entropic properties, potentially leading to high-efficiency energy generation and refrigeration applications. Although hysteresis losses that limit these applications can be reduced through careful control of alloy composition, compositional tuning can also unfavorably influence transformation temperatures and magnetocaloric coupling strength. Hence, exploration of additional processing variables enabling independent control of transformation properties is crucial. In this work, we investigate the role of thermal history as an additional processing variable, exploiting thermally-activated mechanisms to control properties of non-diffusive transformations in (Mn, Fe) 2 (P, Si) alloys. In so doing, we report an unusual transformation-splitting phenomenon following annealing at intermediate times, where a single well-defined magneto-structural transformation evolves towards a multi-step transformation with individual steps occurring at multiple distinct temperatures. Here, on longer annealing at the same temperatures, single-step transformation behavior is recovered. Through additional magnetic and crystallographic characterization, we show that the thermal history-controlled multi-step behavior results from sluggish thermally-activated diffusion. The two-step transformation corresponds to non-equilibrium bimodal composition distributions in the transforming phase, and these develop through a dynamic re-equilibration process as the alloy passes relatively slowly between different thermal equilibria. Together, these results suggest that thermal history primarily controls the transformation properties of (Mn, Fe) 2 (P, Si) alloys indirectly through the composition of one or more transforming phases. Additional investigations are needed to develop thermal history processing for decoupling hysteresis control from other transformation properties.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2020

Relating Texture and Thermomechanical Processing Variables in Mg–Zn–Ca Alloys

It is well known that the strong basal texture commonly produced in magnesium alloy sheets leads to poor formability at room temperature. A sizable body of work has explored how changing the alloy composition and rolling conditions can yield more desirable textures; however important thermomechanical variables, such as the feed rate during rolling, are often not included in the literature, making it difficult to correlate how changes in processing affect the final crystallographic texture. This work explores the texture evolution and grain refinement in Mg-Zn-Ca alloys during plane strain compression (PSC) using a Gleeble thermomechanical simulator. This instrument allows for precise control and capture of the thermomechanical history of the sample. The texture and grain morphology of the compressed samples were characterized using Electron Backscatter Diffraction (EBSD). The texture results will be used to identify which alloys and processing conditions should be scaled up for future rolling studies.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Preliminary results addressing material qualification using combined ion irradiation and modeling data

Additively-manufactured (AM) materials have attracted increasing attention in recent years as a new method to make novel and customized components. While AM and conventionally produced materials are compositionally similar, they do possess different microstructures, necessitating assessment of materials produced via AM for their behavior in reactor environments. Some microstructures unique to AM materials, such as compositional micro-inhomogeneity and dislocation cell structures, are of particular importance since they may lead to different radiation performance. The performance of AM materials for advanced nuclear reactor applications is of interest to the Advanced Materials and Manufacturing Technologies (AMMT) program under the Department of Energy Office of Nuclear Energy. The AMMT program aims to demonstrate its new accelerated development and qualification methods via laser powder bed fusion (LPBF) 316 stainless steel (SS). Focusing on material bearing both 316L and 316H specifications, we integrate ion irradiation and modeling. This year, we focus on answering foundational questions related to process variability, alloy chemistry variation, and microchemical segregation. Experimental results provide information and motivate questions to the modeling effort, which aims to develop the ability to model radiation-driven microstructural evolution in additively-manufactured 316 stainless steel under a variety of advanced reactor conditions, including different temperatures, neutron spectra, and fluxes, in a sort of "virtual experiment". We perform in-situ and ex-situ ion irradiations and microstructural characterizations to support the development of AM materials for reactor applications, develop a phase field model of radiation-induced segregation in additively manufactured material with high angle grain boundaries and dislocation cells, and investigate the effect of carbon and chromium content on point defect behavior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023