Engineering Papers⌕ Search

Engineering topics

Materials science

Explore NASA and DOE materials research. Search alloys, composites and material properties, then open the original technical report for test conditions and results.

Follow this topic with RSS
At least 1,639 records · Page 91
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

3-D Modeling of Directional Solidification of a Non-Dilute Alloy with Temperature and Concentration Fields Coupling via Materials Properties Dependence and via Double Diffusive Convection

Numerical simulation of the HgCdTe growth by the vertical Bridgman method was performed using FIDAP finite element code. Double-diffusive melt convection is analyzed, as the primary factor at controls inhomogeneity of the solidified material. Temperature and concentration fields in the model are also coupled via material properties, such as thermal and solutal expansion coefficients with the dependence on both temperature and concentration, and melting temperature evaluation from pseudobinary CdTe-HgTe phase diagram. Experimental measurements were used to obtain temperature boundary conditions. Parametric study of the melt convection dependence on the gravity conditions was undertaken. It was found, that the maximum convection velocity in the melt can be reduced under certain conditions. Optimal conditions to obtain a near flat solidified interface are discussed. The predicted interface shape is in agreement with one obtained experimentally by quenching. The results of 3-D calculations are compared with previous 2- D findings. A video film featuring 3-D melt convection will be presented.

Bune, Andris V.↗
NASA NTRS2000

Composite, Cryogenic, Conformal, Common Bulkhead, Aerogel-Insulated Tank (CBAT) Materials and Processing Methodologies

A viewgraph presentation outlines the current status and future activities of the composite, cryogenic, conformal, common bulkhead, aerogel-insulated tank (CBAT). Each term (composite, cryogenic, conformal, etc.) is explained. The fabrication method for the CBAT is described, including challenges and their solutions. Near term and long term goals are discussed.

Kovach, Michael P.↗
NASA NTRS2001

Development of Tough, Strong, and Pest-Resistant MoSi2-(Beta)Si3N4 Composites for High-Temperature Structural Applications

A new MoSi2-base composite was developed that contains in-situ reinforcement of whisker-type beta-Si3N4 grains in a MoSi2 matrix. The advantages of this in-situ reinforced MoSi2-Si3N4 are lower density, higher fracture toughness and better strength than typical MoSi2 alloys, combined with excellent environmental and pest resistance. The average fracture toughness of the in-situ reinforced material determined by one technique was 12.2 MPa.m(exp 1/2) compared to 4.9 to 5.5 MPa.m(exp 1/2) for similar materials with the exception that the beta-Si3N4 had a blocky morphology as opposed to the whisker-like morphology typical of the in-situ toughened material. This MoSi2-(beta)Si3N4 was also resistant to pesting at intermediate temperatures (400 to 600 C) even when precracked or under applied load; conditions that would quickly reduce typical MoSi2 alloys to oxidized powder.

Hebsur, M. G.↗
NASA NTRS2002

Development of Novel Composite and Random Materials for Nonlinear Optics and Lasers

A qualitative model explaining sharp spectral peaks in emission of solid-state random laser materials with broad-band gain is proposed. The suggested mechanism of coherent emission relies on synchronization of phases in an ensemble of emitting centers, via time delays provided by a network of random scatterers, and amplification of spontaneous emission that supports the spontaneously organized coherent state. Laser-like emission from powders of solid-state luminophosphors, characterized by dramatic narrowing of the emission spectrum and shortening of emission pulses above the threshold, was first observed by Markushev et al. and further studied by a number of research groups. In particular, it has been shown that when the pumping energy significantly exceeds the threshold, one or several narrow emission lines can be observed in broad-band gain media with scatterers, such as films of ZnO nanoparticles, films of pi-conjugated polymers or infiltrated opals. The experimental features, commonly observed in various solid-state random laser materials characterized by different particle sizes, different values of the photon mean free path l*, different indexes of refraction, etc.. can be described as follows. (Liquid dye random lasers are not discussed here.)

Noginov, Mikhail↗
NASA NTRS2003

Microcrack Quantification in Composite Materials by a Neural Network Analysis of Ultrasound Spectral Data

Intra-ply microcracking in unlined composite pressure vessels can be very troublesome to detect and when linked through the thickness can provide leak paths that may hinder mission success. The leaks may lead to loss of pressure/propellant, increased risk of explosion and possible cryo-pumping into air pockets within the laminate. Ultrasonic techniques have been shown capable of detecting the presence of microcracking and in this work they are used to quantify the level of microcracking. Resonance ultrasound methods are utilized with artificial neural networks to build a microcrack prediction/measurement tool. Two networks are presented, one unsupervised to provide a qualitative measure of microcracking and one supervised which provides a quantitative assessment of the level of microcracking. The resonant ultrasound spectroscopic method is made sensitive to microcracking by tuning the input spectrum to the higher frequency (shorter wavelength) components allowing more significant interaction with the defects. This interaction causes the spectral characteristics to shift toward lower amplitudes at the higher frequencies. As the density of the defects increases more interactions occur and more drastic amplitude changes are observed. Preliminary experiments to quantify the level of microcracking induced in graphite/epoxy composite samples through a combination of tensile loading and cryogenic temperatures are presented. Both unsupervised (Kohonen) and supervised (radial basis function) artificial neural networks are presented to determine the measurable effect on the resonance spectrum of the ultrasonic data taken from the samples.

Walker, James L.↗
NASA NTRS2010

MoS2-Filled PEEK Composite as a Self-Lubricating Material for Aerospace Applications

At BAM, several projects were conducted in the past years dealing with the tribological properties of friction couples at cryogenic temperature and in vacuum environment. Promising candidates for vacuum application are MoS2-filled PEEK/PTFE composites, which showed a friction coefficient as low as 0.03 in high vacuum. To complete the tribological profile of these composites, further tests were performed in ultra-high vacuum (UHV) at room temperature. In this paper, friction and stick slip behavior, as well as outgassing characteristics during the test are presented.

Theiler, Geraldine↗
NASA NTRS2013

The Effect of Scale Dependent Discretization on the Progressive Failure of Composite Materials Using Multiscale Analyses

A multiscale modeling methodology, which incorporates a statistical distribution of fiber strengths into coupled micromechanics/ finite element analyses, is applied to unidirectional polymer matrix composites (PMCs) to analyze the effect of mesh discretization both at the micro- and macroscales on the predicted ultimate tensile (UTS) strength and failure behavior. The NASA code FEAMAC and the ABAQUS finite element solver were used to analyze the progressive failure of a PMC tensile specimen that initiates at the repeating unit cell (RUC) level. Three different finite element mesh densities were employed and each coupled with an appropriate RUC. Multiple simulations were performed in order to assess the effect of a statistical distribution of fiber strengths on the bulk composite failure and predicted strength. The coupled effects of both the micro- and macroscale discretizations were found to have a noticeable effect on the predicted UTS and computational efficiency of the simulations.

Ricks, Trenton M.↗
NASA NTRS2015

Aeroplastic, New Composite Materials with Reduced Heat Transfer and Increased Flame Retardancy

A new composite system formulated using commodity grade and engineered grade polymers. The composites can be fabricated into fibers, molded, or otherwise processed into useable articles. Use of this technology reduces the thermal conductivity and peak heat releases rates of the base polymer between 20%-50% while maintaining or enhancing the mechanical properties..

Flame Retardancy↗
NASA NTRS2019

Spectroscopic Behavior of Composite, Black Thermal Paint, Solar Cell, and Multi-Layered Insulation Materials in a GEO Simulated Environment

The population of objects orbiting Earth is dominated by orbital debris. The following study presents reflectance spectroscopic measurements and bidirectional reflectance distribution function (BRDF) evaluations taken on common spacecraft materials (Table 1), some of which are likely candidates in the orbital debris population. Their optical properties were assessed in their pristine conditions, as well as after exposure in a space environmental chamber used to simulate space weathering. The materials studied will prove that they have excellent properties in resisting the effects of damage that are common in both low Earth orbit and geosynchronous Earth orbit (GEO) based on the research discussed in this work.

Reyes, Jacqueline A.↗
NASA NTRSDate not supplied

Unified Material-Environment Interaction Model for Binary UHTC Composites

A new model for the surface chemistry of zirconium and hafnium diborides containing silicon-carbide when exposed to high temperature conditions in air is formulated. Oxidation dynamics are simplified by considering the diffusion-limited equilibrium regime within the material at elevated temperatures. This model is first assessed against experimental mass-gain data taken from UHTC samples heated to high temperature in an oxygen environment. Then, further evaluations of the new model are conducted using hypersonic CFD simulations to analyze conditions experienced by HfB2-SiC in arc jet experiments conducted at NASA Ames Research Center. Measurements of stagnation point heat transfer and pressure are then used to calibrate the simulations. Results of coupled CFD-material response simulations are then compared to the surface temperatures measured during the Ames arc jet test. Results support the use of the proposed model while highlighting the need for improved gas-phase data on the additional constituents considered.

ultra high temperature ceramic↗
NASA NTRS2022

SiAl Composite Feedhorn Arrays for Astrophysical Applications: Cryogenic Material Properties

A study investigating the physical properties and use of the SiAl composite Controlled Expansion 7 (CE7) for the packaging of silicon bolometric detectors for millimeter-wave astrophysical applications at cryogenic temperatures is presented. The existing interfaces to such detectors are typically made of either ductile metals or micro-machined silicon. As a composite of Si and Al, we find that CE7 exhibits properties of both in ways that may be advantageous for this application. This exploration of the physical properties of CE7 reveals: (a) superconductivity below a critical transition temperature, T_c ∼ 1.2 K; (b) a thermal contraction profile much closer to Si than metal substrates; (c) the relatively low thermal conductivity anticipated for a superconductor, which can be improved by Au-plating; and (d) the feasibility of machining mechanical features with tolerances of ∼25 µm. We further discuss the use of CE7 in the cosmology large angular scale surveyor telescope array, which deployed CE7 in several of its detector focal planes.

Aamir M. Ali↗
DOE OSTI2020

Composite materials with self-regulated infrared emissivity and environment responsive fibers

A composite fabric having self-regulating Infrared emissivity includes meta fibers formed with optical nanostructures and an environment (temperature and/or moisture) responsive mechanism configured to adjust a relative disposition between the optical structures to control the electromagnetic coupling therebetween, thus regulating the infrared emissivity of the composite fabric to maintain a user of the fabric in a temperature/moisture comfort zone. The environment responsive mechanism may include a temperature responsive polymer layer on the fiber capable of expansion/shrinkage depending on the applied temperature, or a moisture responsive fiber changing its shape depending on the moisture level to affect spacing between the optical nanostructures.

Wang, Yuhuang↗
DOE OSTI2024

Analysis of the Surface Morphology and Chemical Composition of Zr-Nb3Sn Alloys with Zr Different Concentrations

The Zr inclusion in Nb3Sn can improve the high magnetic field performance of Nb3Sn radio frequency cavities. The focus of this project is to characterize the surface properties and chemical composition of Zr-Nb3Sn. Nb3Sn was doped with two different concentrations of Zr. ~0.5%, and ~24% Zr. Various spectroscopy techniques were used to examine how the surface morphology and chemical composition changes with increasing Zr fraction in Nb3Sn.

Sue, Micah↗
DOE OSTI2022

A laser ultrasonics-based approach for rapid screening of high entropy alloys

The primary objective of this seed project is to develop a laser ultrasonics-based characterization methodology for rapid metallic materials design and discovery via in situ determination of phases, microstructures and elastic properties with respect to temperature. Ultrasonic waves are strongly affected by material microstructure, and therefore, serve as a facile means to probe elastic properties, phase content and their size distributions and volume fractions. In this study, a laser ultrasonic technique will be used to systematically study the evolution of properties in a set of interrelated simple binary alloys and high entropy alloys (HEA). Phase transformations and microstructural changes inferred from the ultrasonic signals will be correlated with electron microscopy data and predictions using calculations of phase diagrams (CALPHAD). The non-contact and non-destructive ultrasonic testing approach developed in this study could overcome several limitations associated with current material characterization methods for materials discovery. It is expected that the products of the proposed work will be utilized to evaluate novel graded composition HEAs currently being developed at the Idaho National Laboratory (INL) using advanced manufacturing methods based on direct energy deposition and spark plasma sintering processes, and contribute to accelerate the discovery of HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ab initio study of tungsten-based alloys under fusion power-plant conditions

Tungsten (W) is considered a leading candidate for structural and functional materials in future fusion energy devices. The most attractive properties of tungsten for magnetic and inertial fusion energy reactors are its high melting point, high thermal conductivity, low sputtering yield, and low long-term disposal radioactive footprint. However, tungsten also presents a very low fracture toughness, primarily associated with intergranular failure and bulk plasticity, limiting its applications. In recent years, several families of tungsten-based alloys have been explored to overcome the aforementioned limitations of pure tungsten. These include tungsten-based high-entropy alloys (W-HEAs) and tungsten-based Self-passivating Metal Alloys with Reduced Thermo-oxidation or “SMART alloys” (W-SAs). Given their proximity to the plasma, it is crucial to understand how the exposure of these candidate plasma-facing materials (PFMs) to the neutron fluxes expected in fusion reactors impacts their material behavior over time. In this work, we present a computational approach that combines inventory codes and first-principles DFT electronic structure calculations to understand the behavior of transmuting tungsten-based PFMs. In particular, we calculate the changes in the chemical composition, production uncertainties, the elastic and ductility properties, and the density of states for five tungsten-based PFMs when exposed to EU-DEMO fusion first wall conditions for ten years.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

High Carrier Lifetimes in Epitaxial Germanium-Tin/Al(In)As Heterostructures with Variable Tin Compositions

Group IV-based germanium-tin (Ge1-ySny) compositional materials have recently shown great promise for infrared detection, light emission and ultra-low power transistors. High carrier lifetimes are desirable for enhancing the detection limit and efficiency of photodetectors, low threshold current density in lasers, and low tunneling barrier height by lowering defects and dislocations at the heterointerface of a source and a channel. Here, carrier lifetimes in epitaxial germanium (Ge) and variable tin (Sn) compositional Ge1-ySny materials were experimentally determined on GaAs substrates using the contactless microwave photoconductive decay (u-PCD) technique at an excitation wavelength of 1500 nm. Sharp (2 x 2) reflection high energy electron diffraction patterns and low surface roughness were observed from the surface of the Ge0.97Sn0.03 epilayer. X-ray rocking curves from Ge0.97Sn0.03 and Ge0.94Sn0.06 layers demonstrated the pseudomorphic and lattice-matched growth on AlAs and In0.12Al0.88As buffers, respectively, further substantiated by reciprocal space maps and abrupt heterointerfaces evident from the presence of Pendellosung oscillations. High effective carrier lifetimes of 150 ns to 450 ns were measured for Ge1-ySny epilayers as a function of Sn composition, surface roughness, growth temperature, and layer thickness. The observed increase in the carrier lifetime with an increasing Ge layer thickness and a reducing surface roughness, by incorporating Sn, were explained. The enhancement of the carrier lifetime with an increasing Sn concentration was achieved by controlling the defects with lattice-matched Ge0.94Sn0.06/In0.12Al0.88As heterointerfaces or the pseudomorphic growth of Ge0.94Sn0.06 on GaAs. Therefore, our monolithic integration of variable Sn alloy compositional Ge1-ySny materials with high carrier lifetimes opens avenues to realize electronic and optoelectronic devices.

carrier lifetimes↗
DOE OSTI2025

A reversible solvent segregation transition at grain boundaries in gold-platinum alloys

Solute segregation to grain boundaries in polycrystalline metals and ceramics is a well-known phenomenon that reduces the total energy of the material. In this letter, the segregation of the solvent (Au) to grain boundaries in a binary Au 1-x Pt x (x = 0.15 to 0.18) alloy is demonstrated. After heating in the range of 500 °C to 600 °C and quenching to room temperature, grain boundaries in the alloy are enriched in Au at a mean level of ∼ 4 atoms/nm 2 . When the alloy is annealed at 300 °C and quenched, the mean grain boundary composition is closer to the bulk composition. When the alloy is reheated to 500 °C, the segregation is reestablished, demonstrating that the transformation from the strongly segregated complexion to the weakly segregated complexion is reversible. The driving force for the solvent segregation is likely the lower grain boundary energy of Au in comparison to Pt.

36 MATERIALS SCIENCE↗