Engineering topics
Explore NASA and DOE materials research. Search alloys, composites and material properties, then open the original technical report for test conditions and results.
A uniform composite of hypermonotectic composition and a method for producing the same wherein the composition has a plurality of aligned and constrained fibers therein. These fibers serve to uniformly distribute L.sub.11 from the reaction L.sub.I .fwdarw.S.sub.I +L.sub.II.
A team consisting of Arizona State University, Honeywell Engines, Systems & Services, the National Aeronautics and Space Administration Glenn Research Center, and SRI International collaborated to develop computational models and verification testing for designing and evaluating turbine engine fan blade fabric containment structures. This research was conducted under the Federal Aviation Administration Airworthiness Assurance Center of Excellence and was sponsored by the Aircraft Catastrophic Failure Prevention Program. The research was directed toward improving the modeling of a turbine engine fabric containment structure for an engine blade-out containment demonstration test required for certification of aircraft engines. The research conducted in Phase II began a new level of capability to design and develop fan blade containment systems for turbine engines. Significant progress was made in three areas: (1) further development of the ballistic fabric model to increase confidence and robustness in the material models for the Kevlar(TradeName) and Zylon(TradeName) material models developed in Phase I, (2) the capability was improved for finite element modeling of multiple layers of fabric using multiple layers of shell elements, and (3) large-scale simulations were performed. This report concentrates on the material model development and simulations of the impact tests.
Our analyses of the Wild-2 samples returned by the Stardust Mission have illuminated critical gaps in our understanding of related astromaterials. There is a very large database of olivine and low-calcium pyroxene compositions for coarse-grained components of chondrites, but a sparse database for anhydrous silicate matrix phases. In an accompanying figure, we present comparisons of Wild-2 olivine with the available chondrite matrix olivine major element data. We thus have begun a long-term project measuring minor as well as major element compositions for chondrite matrix and chondritic IDPs, and Wild 2 grains. Finally, we wish to re-investigate the changes to fine-grained olivine and low-Ca pyroxene composition with progressive thermal metamorphism. We have examined the LL3-4 chondrites which because of the Hayabusa Mission have become very interesting.
NASA Glenn Research Center, in collaboration with GE Aviation, has begun the development of a smart adaptive structure system with piezoelectric (PE) transducers to improve composite fan blade damping at resonances. Traditional resonant damping approaches may not be realistic for rotating frame applications such as engine blades. The limited space in which the blades reside in the engine makes it impossible to accommodate the circuit size required to implement passive resonant damping. Thus, a novel digital shunt scheme has been developed to replace the conventional electric passive shunt circuits. The digital shunt dissipates strain energy through the load resistor on a power amplifier. General Electric (GE) designed and fabricated a variety of polymer matrix fiber composite (PMFC) test specimens. Investigating the optimal topology of PE sensors and actuators for each test specimen has revealed the best PE transducer location for each target mode. Also a variety of flexible patches, which can conform to the blade surface, have been tested to identify the best performing PE patch. The active damping control achieved significant performance at target modes. This work has been highlighted by successful spin testing up to 5000 rpm of subscale GEnx composite blades in Glenn s Dynamic Spin Rig.
A series of binary and ternary Pt-alloys, that promote the important reactions for catalysis at an alloy surface; oxygen reduction, hydrogen oxidation, and hydrogen and oxygen evolution. The first two of these reactions are essential when applying the alloy for use in a PEMFC.
A series of binary and ternary Pt-alloys, that promote the important reactions for catalysis at an alloy surface; oxygen reduction, hydrogen oxidation, and hydrogen and oxygen evolution. The first two of these reactions are essential when applying the alloy for use in a PEMFC.
Short alumina fibers were added to LSCo contact material to enhance the contact strength and improve thermal cycle stability. Alumina fiber from 2.5 v% to 20 v% were mixed with LSCo and sintered at elevated temperatures. Sintering study showed retardation in densification of LSCo matrix with increasing alumina content. Sintered bulk strength exhibited similar behavior where strength greatly reduced at high alumina v%. Coefficient of thermal expansion showed consistent results with prediction from rule of mixture. Contact strength using anode supported YSZ bilayer coupons improved greatly with the presence of small amount (2.5-5 v%) alumina fibers and no substantial reduction after 10 deep thermal cycles. Candidate LSCo-Al2O3 contact materials was validated in a generic stack test fixture for 1000h at 800oC followed by 10 thermal cycles. Results of impedance analysis showed substantial improvement in thermal cycle stability as compared to LSCo parent materials.
The Materials Technology Program supports the Vehicle Technologies Office’s (VTO’s) mission to help consumers and businesses reduce their transportation energy costs while meeting or exceeding vehicle performance expectations. The propulsion materials research portfolio seeks to develop higher performance materials that can withstand increasingly extreme environments and address the future properties needed for a variety of high-efficiency powertrain types, sizes, fueling concepts, and combustion modes. The lightweight materials research portfolio enables improvements in fuel economy by providing properties that are equal to or better than traditional materials at a lower weight. Because it takes less energy to accelerate a lighter object, replacing cast-iron and traditional steel components with lightweight materials such as advanced high-strength steels, magnesium (Mg) alloys, aluminum (Al) alloys, and fiber-reinforced polymer composites can directly reduce a vehicle’s fuel consumption. By 2025, Materials Technology research activities seek to enable a 25% weight reduction of the glider for light-duty (LD) vehicles including body, chassis, and interior as compared to a 2015 baseline at no more than a $5/lb-saved increase in cost.
Excellent irradiation damage resistance demonstrated by multi-principal elemental alloys (MPEAs) has sparked significant interest among researchers, prompting exploration into their vast compositional space, to validate their suitability for nuclear applications. A combined approach of thermodynamic and empirical parameters calculations alongside CALPHAD (CALculation of PHAse Diagrams) for phase formation predictions enable high-throughput material selection for sophisticated applications like nuclear, overcoming laborious and time-consuming experiments. Key thermodynamic and empirical parameters for eight novel equiatomic MPEAs, based on seven low thermal neutron cross section refractory elements, for predicting phase formation were calculated, and equilibrium and non-equilibrium simulations in CALPHAD were employed to comprehensively model the systems. Pseudo binary phase diagram simulations showed that Zr, V or equiatomic CrV additions to the base MoNbTi alloy (MoNbTi-Zr, MoNbTi-V and MoNbTi-CrV alloys) favor the formation of isomorphous body-centered cubic (BCC) phase at high temperatures, while Cr, Al, equiatomic ZrV, or equiatomic CrAl additions (MoNbTi-Cr, MoNbTi-Al, MoNbTi-ZrV or MoNbTi-CrAl alloys) limit the solubility of them. Equilibrium CALPHAD simulations at 750 oC were consistent with XRD results on MoNbTi, MoNbTiZr and MoNbTiCr alloys, and partially for others. Notably, elemental segregation observed in the backscattered electron (BSE) scanning electron microscopy (SEM) images of the alloys was accurately simulated through non-equilibrium Scheil solidification calculations in CALPHAD, further verified by experiments. The precipitation of TiCr2 Laves phase in Cr containing MoNbTiCr and MoNbTiCrAl was accurately predicted while discrepancies were noted in MoNbTiCrV. The equilibrium simulations also provided insights into phase compositions at specific temperatures offering a pathway for tailoring the desired microstructure and properties of these systems. Empirical parameters calculations successfully predicted random solid solution in the base MoNbTi alloy, and with an exception in MoNbTiV and MoNbTiAl, predicted intermetallic precipitation in the rest, especially, Laves phase precipitation in Cr containing alloys.
Today, a major thrust for achieving engine components with improved thermal capability is the development of fiber-reinforced silicon-carbide (SiC) matrix composites. These materials are not only lighter and capable of higher use temperatures than state-of-the-art metallic alloys and oxide matrix composites (approx. 1100 C), but they can provide significantly better static and dynamic toughness than unreinforced silicon-based monolithic ceramics. However, for successful application in advanced engine systems, the SiC matrix composites should be able to withstand component service stresses and temperatures for the desired component lifetime. Since the high-temperature structural life of ceramic materials is typically controlled by creep-induced flaw growth, a key composite property requirement is the ability to display high creep resistance under these conditions. Also, because of the possibility of severe thermal gradients in the components, the composites should provide maximum thermal conductivity to minimize the development of thermal stresses. State-of-the-art SiC matrix composites are typically fabricated via a three-step process: (1) fabrication of a component-shaped architectural preform reinforced by high-performance fibers, (2) chemical vapor infiltration of a fiber coating material such as boron nitride (BN) into the preform, and (3) infiltration of a SiC matrix into the remaining porous areas in the preform. Generally, the highest performing composites have matrices fabricated by the CVI process, which produces a SiC matrix typically more thermally stable and denser than matrices formed by other approaches. As such, the CVI SiC matrix is able to provide better environmental protection to the coated fibers, plus provide the composite with better resistance to crack propagation. Also, the denser CVI SiC matrix should provide optimal creep resistance and thermal conductivity to the composite. However, for adequate preform infiltration, the CVI SiC matrix process typically has to be conducted at temperatures below 1100 C, which results in a SiC matrix that is fairly dense, but contains metastable atomic defects and is nonstoichiometric because of a small amount of excess silicon. Because these defects typically exist at the matrix grain boundaries, they can scatter thermal phonons and degrade matrix creep resistance by enhancing grain-boundary sliding. To eliminate these defects and improve the thermomechanical properties of ceramic composites with CVI SiC matrices, researchers at the NASA Glenn Research Center developed a high-temperature treatment process that can be used after the CVI SiC matrix is deposited into the fiber preform.
The Materials Technology subprogram supports the Vehicle Technologies Office’s (VTO’s) mission to accelerate the deployment of clean energy technology toward achieving net-zero emissions in the transportation sector. The Propulsion Materials research portfolio seeks to develop higher performance materials that can withstand increasingly extreme environments and address the future properties needed for a variety of high-efficiency powertrain types, sizes, fueling concepts, and combustion modes. The Lightweight Materials research portfolio enables improvements in fuel economy by providing properties that are equal to or better than traditional materials at a lower weight. Because it takes less energy to accelerate a lighter object, replacing cast-iron (Fe) and traditional steel components with lightweight materials—such as advanced high-strength steels (AHSS), magnesium (Mg) alloys, aluminum (Al) alloys, and fiber-reinforced polymer composites—can directly reduce a vehicle’s fuel consumption. By 2025, the Materials Technology research activities seek to enable a 25% weight reduction of the glider for light-duty (LD) vehicles including body, chassis, and interior as compared to a 2015 baseline at no more than a $5/lb-saved increase in cost.
The interest in high entropy alloys and other metallic compounds with four or more elements at near-equiatomic ratios has drawn attention to the ability to rapidly predict phase behavior of these complex materials, particularly where existing thermodynamic data are lacking. In this paper, we discuss aspects of this from the point of view of predicting without utilizing (or fitting) experimental data. Of particular interest are heuristic approaches that provide prediction of single-phase compositions, more rigorous approaches that tackle the thermodynamics from a more fundamental point of view, and simulation approaches that provide further insight into the behaviors. This paper covers cases of all three of these, in order to examine the strengths and weaknesses of each approach, and to indicate directions where these may be utilized and improved upon. Of particular interest is moving beyond “which composition may form a solid solution,” to recognizing the importance of underlying thermodynamic realities that affect the temperature- and composition-dependent transformations of these materials.
On the one hand, multi-principal element alloys (MPEAs) have created a paradigm shift in alloy design due to large compositional space, whereas on the other, they have presented enormous computational challenges for theory-based materials design, especially density functional theory (DFT), which is inherently computationally expensive even for traditional dilute alloys. In this paper, we present a machine learning framework, namely PREDICT (PRedict properties from Existing Database In Complex alloys Territory), that opens a pathway to predict elastic constants in large compositional space with little computational expense. The framework only relies on the DFT database of binary alloys and predicts Voigt–Reuss–Hill Young’s modulus, shear modulus, bulk modulus, elastic constants, and Poisson’s ratio in MPEAs. We show that the key descriptors of elastic constants are the A–B bond length and cohesive energy. The framework can predict elastic constants in hypothetical compositions as long as the constituent elements are present in the database, thereby enabling property exploration in multi-compositional systems. We illustrate predictions in a FCC Ni-Cu-Au-Pd-Pt system.
The Materials and Structures for High Performance project has made excellent progress in the development of advanced high-temperature materials and computational materials science tools to enable high-performance, hgh-efficiency, and environmentally compatible propulsion systems. Ceramic matrix composite (CMC) systems with 2700 O F temperature capability are initially being developed for low NO, combustor liners and turbine vanes. The feasibility of pushing CMC technologies to 3000 O F through revolutionary concepts is also being pursued. Achieving fuel savings of 8 to 15 percent requires higher turbine inlet temperatures as well as reductions in engine weight. An advanced disk alloy has been evaluated for application in future engines. Advanced thermal barrier coatings (TBC s) will enable 3200 O F turbine rotor inlet temperature capability. Advanced alloy development and the development of computational tools for the design of these future alloys will further enable attainment of these goals. Innovative lightweight materials, and structural and nozzle aerodynamic concepts are also being developed to reduce the weight of engine static structures to contribute toward overall fuel savings. Rig tests will demonstrate long-term durability of CMC linersand vanes and advanced turbine airfoil alloy systems, as well as fabricability of components with the highest payoff potential using the lightweight materials and structures concepts being developed.
This paper presents the results of a preliminary structural sizing and alternate material trade study for NASA s Crew Exploration Vehicle (CEV) Crew Module (CM). This critical CEV component will house the astronauts during ascent, docking with the International Space Station, reentry, and landing. The alternate material design study considers three materials beyond the standard metallic (aluminum alloy) design that resulted from an earlier NASA Smart Buyer Team analysis. These materials are graphite/epoxy composite laminates, discontinuously reinforced SiC/Al (DRA) composites, and a novel integrated panel material/concept known as WebCore. Using the HyperSizer (Collier Research and Development Corporation) structural sizing software and NASTRAN finite element analysis code, a comparison is made among these materials for the three composite CM concepts considered by the 2006 NASA Engineering and Safety Center Composite Crew Module project.
process has been devised for the fabrication of a pressure vessel that comprises a composite-material (matrix/fiber) shell with a metal liner on its inner surface. The use of the composite material makes it possible for the tank to be strong enough to withstand the anticipated operating pressure and yet weigh less than does an equivalent all-metal tank. The metal liner is used as a barrier against permeation: In the absence of such a barrier, the pressurized gas in the tank could leak by diffusing through the composite-material shell. The figure depicts workpieces at four key stages in the process, which consists of the following steps: 1. A mandrel that defines the size and shape of the pressure vessel is made by either molding or machining a piece of tooling wax. 2. Silver paint is applied to the surface of the mandrel to make it electrically conductive. 3. The ends of the mandrel are fitted with metal bosses. 4. The mandrel is put into a plating bath, wherein the metal liner is electrodeposited. Depending on the applications, the liner metal could be copper, nickel, gold, or an alloy. Typical liner thicknesses range from 1 to 10 mils (0.025 to 0.25 mm). 5. The wax is melted from within, leaving the thin metal liner. 6. A hollow shaft that includes holes and fittings through which the liner can be pressurized is sealed to both ends of the liner. The liner is pressurized to stiffen (and hence stabilize) it for the next step. 7. The pressurized liner is placed in a filament-winding machine, which is then operated to cover the liner with multiple layers of an uncured graphite-fiber/epoxy-matrix or other suitable composite material. 8. The composite-overwrapped liner is cured in an oven. 9. The pressure is relieved and the shaft is removed. The tank is then ready for use. The process as described above accommodates variations: a) The mandrel could be made of a wax that melts at a higher temperature and not removed until the tank is cured in the oven. b) The tank need not be cylindrical or axisymmetric, as long as the filament-winding machine can accommodate the chosen shape. c) Shallow grooves could be formed on the surface of the mandrel to give the liner a bellows-like character for reinforcement and/or to accommodate expansion and contraction.
Nickel-rich layered oxides are widely used as cathode materials for energy-dense lithium-ion batteries. These chemistries, based on the parent compound LiNiO 2 (LNO), are highly sensitive to ambient environments and are known to readily react with moisture and carbon dioxide. As a result, impurities such as lithium hydroxides and lithium carbonates are formed at the LNO surface, compromising electrochemical behavior. Here, we address this issue by coating LNO cathode particles with a hydrophobic barrier layer composed of graphene and ethyl cellulose (GrEC). This coating limits contact between atmospheric moisture and the LNO surface, which minimizes the generation of lithium impurities. This scheme is evaluated by exposing coated LNO to humidified CO 2 for 24 h as an accelerated ambient degradation test. Subsequent spectroscopy, microscopy, and electrochemical characterization show no detectable signatures of carbonates on the LNO surface, thus verifying that the GrEC coating prevents ambient degradation. In conclusion, by demonstrating this methodology for the ultimate nickel-rich chemistry, this approach can likely be generalized to a wide range of ambient-sensitive battery materials.
Diamond field emitter array field emission cathodes (DFEA FECs) are attractive for the next generation of injectors due to their ability to produce transversely shaped beams without the need for complex masking or laser schemes. However, reliability of this cathode technology remains a challenging issue as principal mechanisms guiding and allowing for output beam shaping remained poorly understood. Here, this paper reports the results of testing two DFEA FECs with the same pattern and emitter tip geometry. Although both cathodes were able to sustain gradients of 44 MV/m and produce maximum output integral charge of 0.5 nC per radio frequency pulse, their emission patterns were different. One cathode did not produce a shaped beam, while the other one did. This difference was explained by the extent of the local variations of the diamond material across the arrays as discovered by spatially resolved Raman spectroscopy. The main practical takeaways were (i) tip sharpness was not a prerequisite for producing a shaped beam and instead (ii) material characteristics resulting in different cathode ballast resistance affected emission spatial uniformity across the array and hence the beam shaping.