Engineering topics
Explore NASA and DOE materials research. Search alloys, composites and material properties, then open the original technical report for test conditions and results.
A method for removing a contaminant from a fluid is provided. A positively charged layered double hydroxide is combined with a negatively charged clay material to form adsorption material. The adsorption material is contacted with an aqueous solution containing the contaminant to adsorb the contaminant onto the adsorption material.
Powerpoint slides for ATR Advanced Materials Program Grain Coarse
Functionally graded materials (FGMs) with site specific chemical composition are commonly manufactured by directed energy deposition (DED). Although previous work fabricated an FGM with a compositional variation between a ferritic and austenitic alloy, difficulties arose due to variations in deposit shape with composition change. This problem also occurs for FGMs in literature; however, unlike other cases, the thermophysical properties of these two alloys were similar throughout the build. Here, we investigate the role of chemical composition and surface-active elements on deposit geometry during the manufacture of FGMs by laser DED. Single-track experiments for the relevant FGM compositions are analyzed with results from a well-tested, three-dimensional, transient numerical heat transfer and fluid flow model and thermodynamic calculations. Experiments showed deposit shape varied as a function of composition for constant laser power and scan speed. Thermodynamic analysis indicated that the oxygen solubility in the fusion zone varied significantly for each composition used for the FGM. Numerical modeling revealed that the change in fluid flow caused by Marangoni convection due to dissolved oxygen in the fusion zone were mainly responsible for the changes in deposit shape observed in experiments. Finally, because oxygen can be introduced into the fusion zone through the feedstock as well as the surrounding atmosphere, these findings elucidate a previously unconsidered aspect of process control during DED fabrication of FGMs.
A significant research and development effort is underway to support the qualification of Alloy 709 as a Class A construction material in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Division 5, High Temperature Reactors. This initiative includes a comprehensive Alloy 709 code qualification plan aimed at generating extensive material testing data crucial for compiling the code case data package. The data package is essential in establishing material-specific design parameters for Alloy 709 to be used as Section III, Division 5 Class A construction material for fast reactors, molten salt reactors and gas-cooled reactors. An ASME Section III, Division 5 material code case requires the evaluation of mechanical properties from a minimum of three commercial heats, covering anticipated compositional ranges. A key part of the data package involves fatigue and creep-fatigue testing at elevated temperatures, needed for developing the fatigue design curves and the damage envelope of the creep-fatigue interaction diagram (D-diagram). This paper summarizes the strain-controlled fatigue testing on three commercial heats of Alloy 709 at 760 and 816°C with strain ranges between 0.25% and 3%. The fatigue failure data are used to generate a preliminary fatigue design curve. Additionally, the creep-fatigue testing results at 816°C with tensile hold times of 10, 30, and 60 minutes are presented in support of developing the D-diagram for Alloy 709.
Weight savings in the range from 25 to 35 percent could be achieved on Space Shuttle orbiter components and the thermal protection system (TPS) by employing a suitable graphite/polyimide (Gr/Pi) composite material system as a substitute for the baseline aluminum structural material. Predicted weight savings are based on the superior strength and stiffness-to-density ratios of Gr/Pi composite material over metallic counterparts. Specific strength and stiffness properties of Celion/Larc-160 composite laminates are compared with aluminum and titanium alloys. Aspects of materials and processes development are discussed, taking into account Celion/Larc-160 composite cure cycle and tooling evolution, complex shaped component process development, mechanical and physical properties testing and results, and structural element design fabrication, testing, and results. Attention is given to a demonstration of materials and processing technology, and a Celion/Larc-160 materials and processes summary is presented.
A particle dispersion alloy is one type of metal-ceramic composite material, and is used as heat resistance material, wear resistance material, and electrical material. This material consists of a metal matrix and dispersed particles, and for its unique structure it has both tenacity as a metal and hardness as a ceramic. Its properties improve when the particles become finer and disperse more uniformly. Most of the particle dispersion alloys are produced by the powder metallurgical process. This process is favorable for uniform dispersion of particles, but it consists of complicated techniques such as mechanical alloying and hot extrusion, and has the following drawbacks: (1) it is difficult to fabricate large-sized products; (2) the amount of particles is limited to a few percent; and (3) the process is complicated and expensive. To overcome these drawbacks, recently special attention has been paid to conventional melting process. However, under terrestrial conditions, dispersions separate immediately due to the different specific gravities of the metal matrix and the particles and thermal convection effects. The microgravity environment is, therefore, considered to be an attractive place for fabricating the dispersion alloy. This space experiment is carried out to clarify the influence of microgravity on the properties of the particle dispersion alloy and to obtain a deeper understanding of the experiment under the microgravity environment.
Bulk metallic glasses (BMGs), a class of amorphous metals defined as having a thickness greater than 1 mm, are being broadly investigated by NASA for use in spacecraft hardware. Their unique properties, attained from their non-crystalline structure, motivate several game-changing aerospace applications. BMGs have low melting temperatures so they can be cheaply and repeatedly cast into complex net shapes, such as mirrors or electronic casings. They are extremely strong and wear-resistant, which motivates their use in gears and bearings. Amorphous metal coatings are hard, corrosion-resistant, and have high reflectivity. BMG composites, reinforced with soft second phases, can be fabricated into energy-absorbing cellular panels for orbital debris shielding. One limitation of BMG materials is their inability to be welded, bonded, brazed, or fastened in a convenient method to form larger structures. Cellular structures (which can be classified as trusses, foams, honeycombs, egg boxes, etc.) are useful for many NASA, commercial, and military aerospace applications, including low-density paneling and shields. Although conventional cellular structures exhibit high specific strength, their porous structures make them challenging to fabricate. In particular, metal cellular structures are extremely difficult to fabricate due to their high processing temperatures. Aluminum honeycomb sandwich panels, for example, are used widely as spacecraft shields due to their low density and ease of fabrication, but suffer from low strength. A desirable metal cellular structure is one with high strength, combined with low density and simple fabrication. The thermoplastic joining process described here allows for the fabrication of monolithic BMG truss-like structures that are 90% porous and have no heat-affected zone, weld, bond, or braze. This is accomplished by welding the nodes of stacked BMG composite panels using a localized capacitor discharge, forming a single monolithic structure. This removes many complicated and costly fabrication steps. Moreover, the cellular structures detailed in this work are among the highest- strength and most energy-absorbent materials known. This implies that a fabricated structure made from these materials would have unequaled mechanical properties compared to other metal foams or trusses. The process works by taking advantage of the electrical properties of the matrix material in the metal-matrix composite, which in this case is a metallic glass. Due to the random nanoscale arrangement of atoms (without any grain boundaries), the matrix glass exhibits a near-constant electrical resistivity as a function of temperature. By placing the composite panels between two copper electrode plates and discharging a capacitor, the entire matrix of the panel can be heated to approximately 700 C in 10 milliseconds, which is above the alloy s solidus but below the liquidus. By designing the geometry of the panels into the shape of an egg box, the electrical discharge localizes only in the tips of each pyramidal cell. By applying a forging load during discharge, the nodes of the panels can be fused together into a single piece, which then dissipates heat through radiation back into a glassy state. This means that two panels can be metallurgically fused into one panel with no heat-affected zone, creating a seamless connection between panels. During the process, the soft metal particles (dendrites) that are uniformly distributed in the glassy matrix to increase the toughness are completely unaffected by the thermoplastic joining. The novelty is that a truss (or foam-like) structure can be formed with excellent energy- absorbing capabilities without the need for machining. The technique allows for large-scale fabrication of panels, well-suited for spacecraft shields or military vehicle door panels. Crystalline metal cellular structures cannot be fabricated using the thermoplastic joining technique described here. If metal panels were te assembled into a cellular structure, they would either have to be welded, brazed, bonded, or fastened together, creating a weak spot in the structure at each connection. Welded parts require a welding material to be added to the joint and exhibit a soft and weak heat-affected zone. Brazing and bonding do not form a metallurgical joint and thus exhibit low strengths, especially when the panels are pulled apart and fasteners require high-stress-concentration holes to be drilled. No equivalent rapid heating method exists for assembling metal panels together into cellular structures, and thus, those parts must be foamed, machined, or investment cast if they are to form a monolithic structure. If the crystalline panels were to be joined using capacitive discharge, as with a spot welder, their bond would be very weak, and the panels would have to be extremely thin. In contrast, the strength of joined BMG parts has been demonstrated to have strength comparable to the parent material. This technique opens up the possibility of using large-scale BMG hardware in spacecraft, military, or commercial applications.
Historically, the structural optimization of aerospace components has been done through geometric methods. A monolithic material is chosen based on the best compromise between the competing design limiting criteria. Then the structure is geometrically optimized to give the best overall performance using the single material chosen. Functionally graded materials offer the potential to further improve structural efficiency by allowing the material composition and/or microstructural features to spatially vary within a single structure. Thus, local properties could be tailored to the local design limiting criteria. Additive manufacturing techniques enable the fabrication of such graded materials and structures. This paper presents the results of a graded material study using two titanium alloys processed using electron beam freeform fabrication, an additive manufacturing process. The results show that the two alloys uniformly mix at various ratios and the resultant static tensile properties of the mixed alloys behave according to rule-of-mixtures. Additionally, the crack growth behavior across an abrupt change from one alloy to the other shows no discontinuity and the crack smoothly transitions from one crack growth regime into another.
Directional solidification of eutectic alloys is a promising technique for producing in-situ composite materials exhibiting a balance of properties. Consequently, the microstructure, creep strength and fracture toughness of directionally solidified NiAl-NiAlTa alloys were investigated. Directional solidification was performed by containerless processing techniques to minimize alloy contamination. The eutectic composition was found to be NiAl-15.5 at% Ta and well-aligned microstructures were produced at this composition. A near-eutectic alloy of NiAl-14.5Ta was also investigated. Directional solidification of the near-eutectic composition resulted in microstructures consisting of NiAl dendrites surrounded by aligned eutectic regions. The off-eutectic alloy exhibited promising compressive creep strengths compared to other NiAl-based intermetallics, while preliminary testing indicated that the eutectic alloy was competitive with Ni-base single crystal superalloys. The room temperature toughness of these two-phase alloys was similar to that of polycrystalline NiAl even with the presence of the brittle Laves phase NiAlTa.
Work during the prior four years of this grant has resulted in significant advances in the development of Cu-8 Cr4 Nb and related Cu-Cr-Nb alloys. The alloys are nearing commercial use in the Reusable Launch Vehicle (RLV) where they are candidate materials for the thrust cell liners of the aerospike engines being developed by Rocketdyne. During the fifth and final year of the grant, it is proposed to complete development of the design level database of mechanical and thermophysical properties and transfer it to NASA Glenn Research Center and Rocketdyne. The database development work will be divided into three main areas: Thermophysical Database Augmentation, Mechanical Testing and Metallography and Fractography. In addition to the database development, work will continue that is focussed on the production of alternatives to the powder metallurgy alloys currently used. Exploration of alternative alloys will be aimed at both the development of lower cost materials and higher performance materials. A key element of this effort will be the use of Thermo-Calc software to survey the solubility behavior of a wide range of alloying elements in a copper matrix. The ultimate goals would be to define suitable alloy compositions and processing routes to produce thin sheets of the material at either a lower cost, or, with improved mechanical and thermal properties compared to the current Cu-Cr-Nb powder metallurgy alloys.
Abstract Interest in high entropy alloy thermoelectric materials is predicated on achieving ultralow lattice thermal conductivity κ L through large compositional disorder. However, here it is shown that for a given mechanism, such as mass contrast phonon scattering, κ L will be minimized along the binary alloy with highest mass contrast, such that adding an intermediate mass atom to increase atomic disorder can increase thermal conductivity. Only when each component adds an independent scattering mechanism (such as adding strain fluctuation to an existing mass fluctuation) is there a benefit. In addition, both charge carriers and heat‐carrying phonons are known to experience scattering due to alloying effects, leading to a trade‐off in thermoelectric performance. Analytic transport models are applied, based on perturbation and effective medium theories, to predict how alloy scattering will affect the thermal and electronic transport across the full compositional range of several pseudo‐ternary and pseudo‐quaternary alloy systems. To do so, a multicomponent extension is demonstrated to both thermal and electronic binary alloy scattering models based on the virtual crystal approximation. Finally, it is shown that common functional forms used in computational thermodynamics can be applied to this problem to further generalize the scattering behavior that is modeled.
A magnetocaloric material comprising a La—Fe—Si based alloy composition that is compositionally modified to include a small but effective amount of at least one of Al, Ga, and In to improve mechanical stability of the alloy (substantially reduce alloy brittleness), improve thermal conductivity, and preserve comparable or provide improved magnetocaloric effects. The alloy composition may be further modified by inclusion of at least one of Co, Mn, Cr, and V as well as interstitial hydrogen.
Despite the explosion of interest in topological materials over the last decades, their applications remain limited due to challenges in growth and incorporation with today’s microelectronics. As a potential bridge to close this gap, we investigate the group-IV alloy Ge 1–x Pb x , in the Ge-rich condition using density functional theory and show that relatively low concentrations of Pb (~9.4%) can lead to a topological phase transition. Furthermore, the calculation of the Z 2 invariant for both the random alloy and the alloy with short-range order (SRO) indicate that the topological phase of the material can be directly modified by the degree of SRO. These findings are understood in terms of local structural relaxation, which decreases the bandgap in the random alloy. However, in the SRO case, the mutual avoidance of Pb leads to minimal structural relaxation, alleviating strain. Our findings not only highlight the emerging importance of SRO in alloy properties but also indicate the possibility of constructing topological interfaces between materials of identical composition (and nominally identical structure). Moreover, they uncover a viable avenue toward the monolithic integration of quantum materials with today’s semiconductor industry.
As the nuclear energy sector advances toward next-generation reactors, the need for high-performance fuel cladding materials has become increasingly urgent. Traditional alloys like zirconium and stainless steel are reaching their performance limits under higher temperatures, more corrosive coolants, and extended irradiation. This report presents the development of a new class of fuel cladding materials based on Non-Concentrated Alloys (NCAs) ? multi-element systems designed to deliver enhanced mechanical strength, corrosion resistance, and radiation tolerance. Through a combination of computational modeling (Computer Coupling of Phase Diagrams and Thermochemistry: CALPHAD), simulation-guided alloy selection, and experimental fabrication via arc melting and spark plasma sintering (SPS), three strategic alloy design paths were explored: (1) FeCrAl-based NCAs, (2) refractory-lean neutron-efficient alloys, and (3) equimolar high-entropy compositions. Microstructural analysis confirmed the formation of stable body-centered cubic BCC_A2 phases, while mechanical testing demonstrated hardness values significantly exceeding those of conventional cladding materials. The results highlight the tunability of NCA systems and their potential for balancing strength and ductility ? a critical consideration for in-reactor performance. Looking forward, future work will focus on thermomechanical optimization, CALPHAD refinement, and benchmarking against industry standards to enable scalable deployment. This work not only advances the science of nuclear materials but also supports broader goals in nuclear safety, performance, and nuclear energy innovation.
This study characterizes the microstructural evolution of single-phase complex concentrated solid-solution alloy (CSA) compositions under heavy ion irradiation with the goal of evaluating mechanisms for CSA radiation tolerance in advanced fission systems. Three such alloys, Cr 18 Fe 27 Mn 27 Ni 28 , Cr 15 Fe 35 Mn 15 Ni 35 , and equimolar NbTaTiV, along with reference materials (pure Ni and E90 for the Cr-FeMnNi family and pure V for NbTaTiV) were irradiated at 50 K and 773 K with 1 MeV Kr ++ ions to various levels of displacements per atom (dpa) using in-situ transmission electron microscopy. Cryogenic irradiation resulted in small defect clusters and faulted dislocation loops as large as 12 nm in face-centered cubic (FCC) CSAs. With thermal diffusion suppressed at cryogenic temperatures, defect densities were lower in all CSAs than in their less compositionally complex reference materials indicating that point defect production is reduced during the displacement cascade stage. High temperature irradiation of the two FCC CSA resulted in the formation of interstitial dislocation loops which by 2 dpa grew to an average size of 27 nm in Cr 18 Fe 27 Mn 27 Ni 28 and 10 nm in Cr 15 Fe 35 Mn 15 Ni 35 . This difference in loop growth kinetics was attributed to the difference in Mn-content due to its effect on the nucleation rate by increasing vacancy mobility or reducing the stacking-fault energy.
Grid-to-rod-fretting (GTRF) in pressurized water reactors (PWRs) is known to cause wear and surface damage on the fuel claddings, potentially leading to radioactive leakage. One of the accident-tolerant fuel (ATF) concepts is to use advanced cladding materials that could withstand higher temperatures. Here, we investigated the wear behavior of candidate silicon carbide (SiC)-based composite claddings with different levels of surface finish in fretting against a commercial ZIRLO alloy grid using a unique bench-scale autoclave GTRF rig. The experiments mimicked the environment in an industrial full-assembly PWR simulator. Fretting tests were conducted with a realistic load (~0.5 N) in deionized water under a pressure of 20–23 bar at 204 °C for 100 h. While the SiC/SiC composite claddings showed significantly higher wear resistance than the commercial ZIRLO alloy cladding as expected, the smoother versions experienced surprisingly higher wear than the much softer counterface, ZIRLO grid. The wear mechanism of the SiC/SiC cladding was attributed to the SiC wear debris that was trapped at the fretting interface causing both 3-body and 2-body (embedded into the grid surface) abrasion of the cladding. Rougher SiC/SiC claddings had less material loss but caused more wear on the ZIRLO grid. Finally, pre-oxidized ZIRLO grid showed better compatibility with the SiC/SiC cladding to protect both the cladding and grid as a result of reduced wear debris trapping.
High-entropy alloys (HEAs) represent a promising class of materials with exceptional structural and functional properties. However, their design and optimization pose challenges due to the large composition-phase space coupled with the complex and diverse nature of the phase formation dynamics. In this study, a data-driven approach that utilizes machine learning (ML) techniques to predict HEA phases and their composition-dependent phases is proposed. By employing a comprehensive dataset comprising 5692 experimental records encompassing 50 elements and 11 phase categories, we compare the performance of various ML models. Our analysis identifies the most influential features for accurate phase prediction. Furthermore, the class imbalance is addressed by employing data augmentation methods, raising the number of records to 1500 in each category, and ensuring a balanced representation of phase categories. The results show that XGBoost and Random Forest consistently outperform the other models, achieving 86% accuracy in predicting all phases. Additionally, this work provides an extensive analysis of HEA phase formers, showing the contributions of elements and features to the presence of specific phases. We also examine the impact of including different phases on ML model accuracy and feature significance. Notably, the findings underscore the need for ML model selection based on specific applications and desired predictions, as feature importance varies across models and phases. This study significantly advances the understanding of HEA phase formation, enabling targeted alloy design and fostering progress in the field of materials science.
Refractory high entropy alloys (RHEAs) have been proven to be a potential candidate in the biomedical field due to their balanced mechanical properties and biocompatible composition. Recent experimental findings show that RHEAs like HfNbTaTiZr and Hf 0.5 Nb 0.5 Ta 0.5 Ti 1.5 Zr have good mechanical properties such as high polarization and wear resistance than others which establish them as potential materials for biomedical application. In this work, we performed first-principles density functional theory calculations on the mechanical and thermal properties of HfNbTaTiZr and Hf 0.5 Nb 0.5 Ta 0.5 Ti 1.5 Zr. The predicted lattice constant, density, Young's modulus, and Vickers hardness are consistent with the available experimental report, which verifies the accuracy of the applied model. The thermal coefficient of linear expansion of both RHEAs has been investigated by utilizing the Debye theory. The present methods could be applied to study other future RHEAs on exploration of their physical properties.