Engineering topics

Materials science

Explore NASA and DOE materials research. Search alloys, composites and material properties, then open the original technical report for test conditions and results.

Follow this topic with RSS

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS2001

Thermomechanical Response of Shape Memory Alloy Hybrid Composites

This study examines the use of embedded shape memory alloy (SMA) actuators for adaptive control of the thermomechanical response of composite structures. A nonlinear thermomechanical model is presented for analyzing shape memory alloy hybrid composite (SMAHC) structures exposed to steady-state thermal and dynamic mechanical loads. Also presented are (1) fabrication procedures for SMAHC specimens, (2) characterization of the constituent materials for model quantification, (3) development of the test apparatus for conducting static and dynamic experiments on specimens with and without SMA, (4) discussion of the experimental results, and (5) validation of the analytical and numerical tools developed in the study. Excellent agreement is achieved between the predicted and measured SAMHC responses including thermal buckling, thermal post-buckling and dynamic response due to inertial loading. The validated model and thermomechanical analysis tools are used to demonstrate a variety of static and dynamic response behaviors including control of static (thermal buckling and post-buckling) and dynamic responses (vibration, sonic fatigue, and acoustic transmission). and SMAHC design considerations for these applications. SMAHCs are shown to have significant advantages over conventional response abatement approaches for vibration, sonic fatigue, and noise control.

Turner, Travis L.↗

NASA NTRS1989

Effects of aging condition on the fracture toughness of 2XXX and 7XXX series aluminum alloy composites

Results are presented on the effects of matrix aging condition (i.e., matrix temper) on the fracture toughness of 2XXX and 7XXX Al matrix alloys reinforced with SiC particulates, and the results are compared with the mechanical behavior. Fracture toughness testing was conducted on fatigue precracked bend specimens, and fracture surfaces were examined using SEM. Results revealed dramatic differences in the effect of matrix microstructure on the fracture properties of the two composite series. In the 7XXX material, the toughness values decreased from the underaged (UA) condition to the overaged (OA) condition by approximately 40 percent, while in the 2XXX series composite, the effect of matrix microstructure was marginal. In the 7XXX series composites, a transition in fracture mode from particle cracking (in UA) to matrix and linear-interface failure (in OA) was observed, while the 2XXX series composite failed predominantly by particle cracking.

Manoharan, M.↗

NASA NTRS2018

Laser Ablation Surface Treatment of Structural Aerospace Composites and Metal Alloys for Adhesive Bonding

NASA Langley Research Center (LaRC) has been involved over the past decade in the development of laser ablation as a method to surface treat aerospace structural fiber reinforced composites (CFRPs) and metal alloys. [1- 18] Laser surface treatment has been shown to be a rapid, high precision, and reproducible method for surface treatment of these materials, and is amenable to automation. The laser ablation process removes surface contamination such as silicones, creates surface roughness, and chemically activates a surface for bonding. The degree of ablation is controllable by adjusting laser parameters. In the case of CFRPs, ablation can be performed without damage to any underlying carbon fibers. In the case of metal alloys, ablation is possible without surface embrittlement, heat damage or creation of undesirable grain structures or morphologies. The optimum laser treatment conditions are substrate dependent and generally are influenced by laser wavelength and pulse duration (typically fixed for a laser system), and laser power. In the case of metal alloys such as Ti-6Al-4V, the laser ablation process eliminates the need for several steps of the conventional processes, including hydrofluoric (HF) acid and caustic treatment. These steps are often conducted in dip tanks and require costly facilities and environmentally unfriendly liquids. In addition, the laser can create nano-porosity on the Ti-6Al-4V alloy surface allowing for sol-gel penetration and thereby creating a gradient interface with improved temperature and mechanical performance. NASA LaRC has also been involved with the development of in-line characterization methods compatible with the laser treatment process to rapidly determine the presence of key contaminates such as silicones that, even at very low concentrations, are a threat to adhesive bonding. A spectroscopic technique called micro-laser induced breakdown spectroscopy (u-LIBS) has been developed to rapidly detect silicones at concentrations below those known to cause bonding problems. This technique requires no sample preparation, vacuum or inert atmosphere, has no practical size limitations, and provides nearly instantaneous feedback to the operator. This presentation will give an overview and update of these developments with specific examples highlighted.

Connell, John W.↗

DOE OSTI2023

Sustainable materials acceleration platform reveals stable and efficient wide-bandgap metal halide perovskite alloys

The vast chemical space of emerging semiconductors, like metal halide perovskites, and their varied requirements for semiconductor applications have rendered trial-and-error environmentally unsustainable. Here, in this work, we demonstrate RoboMapper, a materials acceleration platform (MAP), that achieves 10-fold research acceleration by formulating and palletizing semiconductors on a chip, thereby allowing high-throughput (HT) measurements to generate quantitative structure-property relationships (QSPRs) considerably more efficiently and sustainably. We leverage the RoboMapper to construct QSPR maps for the mixed ion FA 1-y Cs y Pb(I 1-x Br x ) 3 halide perovskite in terms of structure, bandgap, and photostability with respect to its composition. We identify wide-bandgap alloys suitable for perovskite-Si hybrid tandem solar cells exhibiting a pure cubic perovskite phase with favorable defect chemistry while achieving superior stability at the target bandgap of ~1.7 eV. RoboMapper’s palletization strategy reduces environmental impacts of data generation in materials research by more than an order of magnitude, paving the way for sustainable data-driven materials research.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Design of functional composite and all-inorganic nanostructured materials via infiltration of polymer templates with inorganic precursors

Robust and efficient approaches for the synthesis of materials with structure, porosity, and composition controlled at the nanoscale are highly important for a wide range of applications. Polymer templates are promising platforms to achieve such control. The self-assembly process of polymers provides access to diverse structures that can serve as templates for the deposition of inorganic materials. By infiltrating metal precursors from gas or liquid phases, using sequential infiltration synthesis (SIS) or swelling-based infiltration (SBI), respectively, into the polymer templates, one can create finely-tuned texturing of the surface films and bulk materials. In this review, we outline the specifics and dynamics of the polymer infiltration process and characterize the structure and properties of the synthesized materials. Finally, we highlight recent progress in implementing polymer infiltration-based nanoporous ceramics for many applications, including sensors, antireflective coatings, oil-absorbing foams, nanolithographic patterns, and catalytic materials.

Berman, Diana↗

DOE OSTI2020

Alloy 709 Materials Procurement

Qualifying a new material for design and construction of elevated temperature nuclear components under Section III Division 5 of the BPVC requires measurement of a variety of properties, including tensile, creep, fatigue and creep-fatigue behavior in the relevant temperature range, and from the relevant product form, from a commercial scale heat. For the ART program the desired product form is hot rolled plate. This procurement is for a unique composition of stainless steel for which a commercial scale heat represents melting about 50,000 pounds of the alloy, resulting in about 45,000 pounds of usable plate. The Alloy 709 plate from this purchase will be provided to INL, Argonne National Laboratory and Oak Ridge National Laboratory for characterization of the relevant properties to support Code qualification.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Feasibility Study of Advanced Manufacturing Techniques and Compositions of High Entropy Alloys

In line with the objectives of Department of Energy’s Office of Nuclear Energy Advanced Materials and Manufacturing technologies program (AMMT), this work focuses on new materials development and qualification research and development for next-generation, high-temperature nuclear reactors. While the currently qualified nuclear materials have demonstrated significant irradiation resistance at high temperatures, the community is still interested in materials that can sustain the harsh environments found in nuclear reactors for temperatures up to 1,000°C for nearly 100,000 hours. High entropy alloys (HEAs) have the potential to serve in these extreme environments of next generation nuclear reactors due to their unique phase transformation pathways and nanoscale and mesoscale microstructures. The current work focuses on understanding such nuclear energy relevant HEAs through a detailed literature survey and developing a decision matrix with criteria for identification of HEAs with may have most impact and value for further examination.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Microstructural evolution of a silicon carbide-carbon coated nanostructured ferritic alloy composite during in-situ Kr ion irradiation at 300°C 450°C

This work focuses on irradiation behaviors of a novel silicon carbide and carbon coated nanostructured ferritic alloy (SiC-C@NFA) composite for potential applications as a cladding and structural material for next generation nuclear reactors. The SiC-C@NFA samples were irradiated with 1 MeV Kr ions up to 10 dpa at 300 and 450 °C. Microstructures and defect evolution were studied in-situ at the IVEM-Tandem facility at Argonne National Laboratory. The effects of ion irradiation on various phases such as α-ferrite matrix, (Fe,Cr) 7 C 3 , and (Ti,W)C precipitates were evaluated. The α-ferrite matrix showed a continuous increase in dislocation density along with spatial ordering of dislocation loops (or loop strings) at >5 dpa. The size of the dislocation loops at 450 °C was larger than that at 300 °C. The nucleation and growth of new (Ti,W)C precipitates in α-ferrite grains were enhanced with the ion dose at 450 °C. This study provides new insight into the irradiation resistance of the SiC-C@NFA system.

(FeCr)(7)C-3↗

NASA NTRS1974

The tensile failure modes of metal-matrix composite materials

The strengths of individual boron fibers extracted from various as-received and thermally fatigued aluminum alloy matrix materials were measured. The results are described in terms of a Weibull distribution, and strengths of composites fabricated from these fibers are calculated in terms of lower and upper bounds. Tests conducted on composite specimens indicated that strengths approaching the upper bounds can be achieved in composites fabricated by normal diffusion bonding techniques. Cyclic temperature changes effectively reduced the strength values toward the lower bounds. It was concluded that this effect resulted from the degradation of the strength of the fiber-matrix bond.

Wright, M. A.↗

NASA NTRS1991

The Role of the Interface in Refractory Metal Alloy Composites

Creep-rupture and tensile tests have been used to evaluate thoriated W-wire reinforced Nb-1 percent Zr alloy matrix composites fabricated via arc-spray monotape technique. A significant creep strength enhancement was observed over the unreinforced matrix alloy while matrix integrity was maintained; the fiber/matrix interface phase is noted to be a strong and ductile W/Nb alloy, which is formed due to the mutual solubility of the constituent metals. High strength, toughness, and thermal stability are demonstrated by this material system, which is also resistant to liquid alkali metal corrosion.

Grobstein, Toni↗

NASA NTRS2007

Effects of Different Braze Materials and Composite Substrates on Composite/Ti Joints

An ever increasing number of applications require robust joining technologies of dissimilar materials. In this study, three types of ceramic composites (C-C, C-SiC, and SiC-SiC) were vacuum brazed to commercially pure Ti using the Cusil-ABA (63 Ag - 35.5 Cu - 1.75 Ti) active metal braze alloy. The study also compared composite specimens as-fabricated and after surface grinding/polishing. A butt-strap tensile shear strength test was used to evaluate the joined structures at room temperature, 270 and 500 C. The elevated temperatures represent possible use temperatures for some heat rejection type applications. Joint strength will be discussed in light of braze wetting and spreading properties, composite properties, and test temperature.

Morscher, Gregory N.↗

DOE OSTI2024

MaterialsMap: A CALPHAD-based tool to design composition pathways through feasibility map for desired dissimilar materials, demonstrated with resistance spot welding joining of Ag-Al-Cu

Assembly of dissimilar metals can be achieved by different methods, for example, casting, welding, and additive manufacturing (AM). However, undesired phases formed in liquid-phase assembling processes due to solute segregation during solidification diminish mechanical and other properties of the processed parts. In the present work, an open-source software named MaterialsMap, has been developed based on the CALculation of Phase Diagrams (CALPHAD) approach. The primary objective of MaterialsMap is to facilitate the design of an optimal composition pathway for assembling dissimilar alloys with liquid-phases based on the formation of desired and undesired phases along the pathway. In MaterialsMap, equilibrium thermodynamic calculations are used to predict equilibrium phases formed at slow cooling rate, while Scheil-Gulliver simulations are employed to predict non-equilibrium phases formed during rapid cooling. Additionally, by combining these two simulations, MaterialsMap offers a thorough guide for understanding phase formation in various manufacturing processes, assisting users in making informed decisions during material selection and production. As a demonstration of this approach, a compositional pathway was designed from pure Al to pure Cu through Ag using MaterialsMap. The design was experimentally verified using resistance spot welding (RSW).

36 MATERIALS SCIENCE↗

NASA NTRS1994

Improved composite material and method for production of improved composite material

A laminated composite material with improved interlaminar strength and damage tolerance having short rods distributed evenly throughout the composite material perpendicular to the laminae is introduced. Each rod is shorter than the thickness of the finished laminate, but several times as long as the thickness of each lamina. The laminate is made by inserting short rods in layers of prepreg material, and then stacking and curing prepreg material with rods inserted therethrough.

Farley, Gary L.↗

NASA NTRS1996

Composite material and method for production of improved composite material

A laminated composite material with improved interlaminar strength and damage tolerance having short rods distributed evenly throughout the composite material perpendicular to the laminae. Each rod is shorter than the thickness of the finished laminate, but several times as long as the thickness of each lamina. The laminate is made by inserting short rods in layers of prepreg material, and then stacking and curing prepreg material with rods inserted therethrough.

Farley, Gary L.↗

DOE OSTI2026

Solidification cracking of refractory alloys: a computational and machine learning study to investigate composition-dependence for improved weldability and additive manufacturability

Large-batch numerical, CALculation of PHAse Diagrams (CALPHAD)-based solidification cracking calculations are performed and then analyzed with machine learning methods to generate models that relate chemistry of refractory alloys to cracking susceptibility. Kou’s solidification cracking index is used to study the refractory alloys including O, N, C binary mixtures with Mo, Ta, Nb, and W, the molybdenum-based TZM, Niobium-based C103, and Tantalum-based T111 and Ta-10 W, as well as hypothetical refractory ternary alloys. Findings strongly validate Kou’s Crack Susceptibility Index (CSI) against Varestraint test data for Nb- and Ta-based alloys, establishing CSI thresholds where refractory alloys with CSI < 15,000 K are likely weldable, CSI > 15,000 K are prone to cracking, and CSI > 25,000 K are likely unweldable (or unprintable). Furthermore, interstitial elements C, N, and O significantly increase crack susceptibility, with some existing material specifications coinciding with peak cracking susceptibility concentrations. Finally, machine learning-derived elemental potency factors enable rapid prediction of CSI from alloy chemistry for C103, TZM, Ta-10 W, and T-111 alloys. These results provide practical guidance for feedstock selection, powder reuse limits, and alloy specification amendments for welding and additive manufacturing applications.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Bismuth in Lead–Tin Alloy Perovskites: Effect on Material Properties and Photovoltaic Device Performance

Metal halide perovskites (MHPs) have a strong potential for optoelectronic applications, especially photovoltaics. A significant advantage offered by MHPs is their bandgap tunability via chemical substitution and alloying, with lead–tin alloys producing the narrowest reported bandgaps of ~1.2 eV. Efforts to further narrow the bandgap of MHPs by alloying in other elements, such as bismuth, have largely been unsuccessful due to the introduction of defective electronic states, which severely diminish electronic quality. Here, in this study, we examine the effects of bismuth on a lead–tin alloyed MHP, motivated by the narrow bandgap of alloyed lead–tin MHPs. We find that the defect screening observed in lead–tin MHPs is not sufficient to screen the defect level introduced by bismuth, as evidenced by quenched photoluminescence, decreased mobility, and severely reduced performance in a photovoltaic device. Density functional theory calculations suggest that midgap states are introduced by bismuth addition over a range of chemical and compositional conditions. We further observe through wavelength-dependent photoconductivity that free carriers are generated out to ~0.9 eV in bismuth-containing samples, which could be of potential interest for NIR photodetection.

14 SOLAR ENERGY↗

DOE OSTI2024

Advanced Manufacturing Techniques and Compositions of High Entropy Alloys for Nuclear Applications

In line with the objectives of the Department of Energy, Office of Nuclear Energy, Advanced Materials and Manufacturing Technologies (AMMT) program, this work focuses on new materials development and qualification research and development for next-generation, high-temperature nuclear reactors. High entropy alloys (HEAs) have the potential to serve in these extreme environments of next-generation nuclear reactors because of their unique phase transformation pathways and nanoscale and mesoscale microstructures. The current work focuses on understanding such nuclear-energy-relevant HEAs through a detailed literature survey, selected experimental work, and developing a decision matrix with criteria for the identification of HEAs that may have the most impact and value for further examination.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Processability and Material Behavior of NiTi Shape Memory Alloys Using Wire Laser-Directed Energy Deposition (WL-DED)

Utilizing additive manufacturing (AM) techniques with shape memory alloys (SMAs) like NiTi shows great promise for fabricating highly flexible and functionally superior 3D metallic structures. Compared to methods relying on powder feedstocks, wire-based additive manufacturing processes provide a viable alternative, addressing challenges such as chemical composition instability, material availability, higher feedstock costs, and limitations on part size while simplifying process development. This study presented a novel approach by thoroughly assessing the printability of Ni-rich Ni55.94Ti (Wt. %) SMA using the wire laser-directed energy deposition (WL-DED) technique, addressing the existing knowledge gap regarding the laser wire-feed metal additive manufacturing of NiTi alloys. For the first time, the impact of processing parameters—specifically laser power (400–1000 W) and transverse speed (300–900 mm/min)—on single-track fabrication using NiTi wires in the WL-DED process was examined. An optimal range of process parameters was determined to achieve high-quality prints with minimal defects, such as wire dripping, stubbing, and overfilling. Building upon these findings, we printed five distinct cubes, demonstrating the feasibility of producing nearly porosity-free specimens. Notably, this study investigated the effect of energy density on the printed part density, impurity pick-up, transformation temperature, and hardness of the manufactured NiTi cubes. The results from the cube study demonstrated that varying energy densities (46.66–70 J/mm3) significantly affected the quality of the deposits. Lower to intermediate energy densities achieved high relative densities (>99%) and favorable phase transformation temperatures. In contrast, higher energy densities led to instability in melt pool shape, increased porosity, and discrepancies in phase transformation temperatures. These findings highlighted the critical role of precise parameter control in achieving functional NiTi parts and offer valuable insights for advancing AM techniques in fabricating larger high-quality NiTi components. Additionally, our research highlighted important considerations for civil engineering applications, particularly in the development of seismic dampers for energy dissipation in structures, offering a promising solution for enhancing structural performance and energy management in critical infrastructure.

Dabbaghi, Hediyeh↗