Engineering topics

Materials science

Explore NASA and DOE materials research. Search alloys, composites and material properties, then open the original technical report for test conditions and results.

Follow this topic with RSS

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS1993

An investigation on the rheological behavior of metallic semi-solid slurries of Al-6.5 pct Si and semi-solid composite slurries of SiC particulates in an Al-6.5 pct Si alloy matrix

The rheology of SiC particulate/Al-6.5 pct Si composite slurries was explored. The rheological behavior of the composite slurries shows both thixotropic and pseudoplastic behaviors. Isostructural experiments on the composite slurries revealed a Newtonian behavior beyond a high shear rate limit. The rheology of fully molten composite slurries over the low to high shear rate range indicates the existence of a low shear rate Newtonian region, an intermediate pseudoplastic region and a high shear rate Newtonian region. The isostructural studies indicate that the viscosity of a composite slurry depends upon the shearing history of a given volume of material. An unexpected shear thinning was noted for SiC particulate + alpha slurries as compared to semi-solid metallic slurries at the same fraction solid. The implications of these findings for the processing of slurries into cast components is discussed.

Moon, H.-K.↗

NASA NTRS1999

Effect of a Nonplanar Melt-Solid Interface On Lateral Compositional Distribution During Unidirectional Solidification of a Binary Alloy with a Constant Growth Velocity V: Theory - Pt. 1

Infrared detected materials, such as Hg(1-x)Cd(x)Te, Hg(1-x)Zn(x)Te have energy gaps almost linearly proportional to their composition. Due to the wide separation of liquidus and solidus curves of their phase diagram, there are compositional segregation in both of the axial and radial directions of these crystals grown in the Bridgman system unidirectionally with constant growth rate. It is important to understand the mechanisms, which affect lateral segregation such that large radially uniform composition crystal can be produced. Following Coriel, etc's treatment, we have developed a theory to study the effect of a curved melt-solid interface shape on lateral composition distribution. The model is considered to be a cylindrical system with azimuthal symmetry and a curved melt-solid interface shape which can be expressed as a linear combination of a series of Bessell's functions. The results show that melt-solid interface shape has a dominant effect on the lateral composition distribution of these systems. For small values of beta, the solute concentration at the melt-solid interface scales linearly with interface shape with a proportional constant of the produce of beta and (1 -k), where beta = VR/D, with V as growth velocity, R as the sample radius, D as the diffusion constant and k as the distribution constant. A detailed theory will be presented. A computer code has been developed and simulations have been performed and compared with experimental results. These will be published in another paper.

Wang, Jai-Ching↗

NASA NTRS1999

Effect of a Nonplanar Melt-Solid Interface on Lateral Compositional Distribution during Unidirectional Solidification of a Binary Alloy with a Constant Growth Velocity V: Theory - Part 1

Infrared detector materials, such as Hg(1-x)Cd(x)Te, Hg(1-x)Zn(x)Te have energy gaps almost linearly proportional to its composition. Due to the wide separation of liquidus and solidus curves of their phase diagram, there are compositional segregations in both of axial and radial directions of these crystals grown in the Bridgman system unidirectionally with constant growth rate. It is important to understand the mechanisms which affect lateral segregation such that large uniform radial composition crystal is possible. Following Coriell, etc's treatment, we have developed a theory to study the effect of a curved melt-solid interface shape on the lateral composition distribution. The system is considered to be cylindrical system with azimuthal symmetric with a curved melt-solid interface shape which can be expressed as a linear combination of a series of Bessell's functions. The results show that melt-solid interface shape has a dominate effect on lateral composition distribution of these systems. For small values of b, the solute concentration at the melt-solid interface scales linearly with interface shape with a proportional constant of the product of b and (1 - k), where b = VR/D, with V as growth velocity, R as sample radius, D as diffusion constant and k as distribution constant. A detailed theory will be presented. A computer code has been developed and simulations have been performed and compared with experimental results. These will be published in another paper.

Wang, Jai-Ching↗

NASA NTRS1974

Composite materials. Volume 3 - Engineering applications of composites. Volume 4 - Metallic matrix composites. Volume 8 - Structural design and analysis, Part 2

This volume discusses a vaety of applications of both low- and high-cost composite materials in a number of selected engineering fields. The text stresses the use of fiber-reinforced composites, along with interesting material systems used in the electrical and nuclear industries. As to technology transfer, a similarity is noted between many of the reasons responsible for the utilization of composites and those problems requiring urgent solution, such as mechanized fabrication processes and design for production. Features topics include road transportation, rail transportation, civil aircraft, space vehicles, builing industry, chemical plants, and appliances and equipment. The laminate orientation code devised by Air Force materials laboratory is included. Individual items are announced in this issue.

Noton, B. R.↗

DOE OSTI2026

Probing multi-dimensional composition spaces in search of strong metallic alloys

Refractory complex concentrated alloys (RCCA) offer exceptionally high-temperature strength compared to pure metals and dilute alloys, but predictive theory for RCCA design is lacking. We present large-scale molecular Dynamics (MD) simulations of crystal plasticity to explore alloy compositions for maximum mechanical strength, focusing on Fe-Ta-W and Nb-Ta-Mo-W alloy families modeled with Embedded Atom Model (EAM) and Spectral Neighbor Analysis Potentials (SNAP). To efficiently guide the search for strong alloy compositions, we employ iterative optimization using Gaussian process regression. Many simulated RCCA compositions exhibit pronounced cocktail strengthening, with strengths surpassing their strongest constituent metal, tungsten. Contrary to expectations, the highest strength is found on binary edges of the RCCA composition space. Detailed analyses of atomistic simulations reveal that, similar to pure BCC metals, plastic response in RCCA is primarily governed by screw dislocations. However, at large strains, dislocation multiplication and interactions (Taylor hardening) become the dominant mechanisms contributing to RCCA strength.

Materials science↗

DOE OSTI2024

Strength-ductility synergy through microstructural and compositional heterogeneity in directed energy deposition additive manufacturing of face-centered cubic materials

Directed energy deposition (DED) is an additive manufacturing (AM) process based on welding technology and offers the advantages of large build volume, high deposition rate, and ability to fabricate multi-material parts. Epitaxial continuous columnar grain growth is a characteristic microstructural feature of DED processed alloys. In this study, a bamboo-like microstructure (periodic alternation of equiaxed and columnar structure) was produced by adopting an intermittent deposition strategy in 316L stainless steel and Inconel 625. The formation of a bamboo-like alternating microstructure was confirmed through electron backscattered diffraction (EBSD) analysis. Hardness mapping showed that the columnar to equiaxed transition (CET) occurred at the region right below the fusion line. A finite element (FE) model was used to investigate the relationship between the temperature gradient (G) and the solidification rate (R). The FE model showed a low G/R ratio at the region right below the interface promoting the CET. The grain size and material-dependent deformation behaviors are analyzed using digital image correlation (DIC). The lower deformation on the fine-grain regions observed in DIC analysis is attributed to a higher strain hardening rate, which is confirmed through dislocation density analysis on a tensile-interrupted specimen. The periodically alternating grain size coupled with the microstructural changes caused by intermittent deposition strategy result in a better strength-ductility synergy in both single-material and bimetallic specimens.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Selective butene formation in direct ethanol-to-C3+-olefin valorization over Zn-Y/Beta and single-atom alloy composite catalysts using in situ generated hydrogen

The selective production of C3+ olefins from renewable feedstocks, especially via C1 and C2 platform chemicals, is a critical challenge for obtaining economically viable low-carbon middle distillate transportation fuels (i.e., jet and diesel). Here, we report a multifunctional catalyst system composed of Zn-Y/Beta and “single-atom” alloy (SAA) Pt-Cu/Al2O3 which selectively catalyzes ethanol-to-olefins (C3+, ETO) valorization in the absence of cofed hydrogen, forming butenes as the primary olefin products. Beta zeolites containing predominately isolated Zn and Y metal sites catalyze ethanol upgrading steps (588 K, 3.1 kPa ethanol, ambient pressure) regardless of cofed hydrogen partial pressure (0-98.3 kPa H2), forming butadiene as the primary product (60% selectivity at 87% conversion). The Zn-Y/Beta catalyst possesses site-isolated Zn and Y Lewis acid sites (at ~7 wt% Y) and Brønsted acidic Y sites, the latter of which has been previously uncharacterized. A secondary bed of SAA Pt-Cu/Al2O3 selectively hydrogenates butadiene to butene isomers at a consistent reaction temperature using hydrogen generated in situ from ethanol-to-butadiene (ETB) conversion. This unique hydrogenation reactivity at near-stoichiometric hydrogen and butadiene partial pressures is not observed over monometallic Pt or Cu catalysts, highlighting these operating conditions as a critical SAA catalyst application area for conjugated diene selective hydrogenation at high reaction temperatures (>573 K) and low H2/diene ratios (e.g., 1:1). Single-bed steady state selective hydrogenation rates, associated apparent hydrogen and butadiene reaction orders, and DFT calculations of the Horiuti-Polanyi reaction mechanisms indicate that the unique butadiene selective hydrogenation reactivity over SAA Pt-Cu/Al2O3 reflects lower hydrogen scission barriers relative to monometallic Cu surfaces and limited butene binding energies relative to monometallic Pt surfaces. DFT calculations further indicate the preferential desorption of butene isomers over SAA Pt-Cu(111) and Cu(111) surfaces while Pt(111) surface favors subsequent butene hydrogenation reactions to form butane over butene desorption events. Under operating conditions without of hydrogen cofeeding, this combination of Zn-Y/Beta and SAA Pt-Cu catalysts can selectively form butenes (65% butenes, 78% C3+ selectivity at 94% conversion) and avoid butane formation using only in situ generated hydrogen, avoiding costly hydrogen cofeeding requirements that hinder many renewable energy processes.

Cordon, Michael↗

DOE OSTI2022

Codesigning Alloy Compositions of CdSe y Te 1− y Absorbers and Mg x Zn 1− x O Contacts to Increase Solar Cell Efficiency

Thin‐film solar cells such as CdTe are a major commercial photovoltaic technology, with more than 25 GW installed worldwide and levelized costs of electricity competitive with fossil fuels. Further progress may result from integrating CdSe y Te 1− y absorbers with Mg x Zn 1− x O contacts, but the device efficiency is difficult to maximize due to coupled dependence on chemical composition of both alloys. Herein, a high‐throughput approach is demonstrated to codesign chemical compositions in alloyed Mg x Zn 1− x O/CdSe y Te 1− y thin‐film solar cells, using combinatorial libraries of PV devices with orthogonal composition gradients in CdSe y Te 1− y absorbers and Mg x Zn 1− x O contacts. It is found that the solar cell performance is a strong and coupled function of both elemental compositions, with efficiency up to 17.7% ( V OC = 836 mV, fill factor = 69%, J SC = 30.6 mA cm −2 ) at atomic compositions of Mg/(Mg + Zn) ≈18% and average Se/(Se + Te) ≈4%. These performance trends among >100 devices are explained by >100 ns lifetime of photoexcited charge carriers at the Mg x Zn 1− x O/CdSe y Te 1− y interface where strong Se accumulation is also observed. This study reports the optimal compositions of the commercially relevant Mg x Zn 1− x O/CdSe y Te 1− y solar cells and demonstrates a general approach to codesigning performance of alloyed thin‐film solar cells and other optoelectronic devices.

14 SOLAR ENERGY↗

DOE OSTI2021

Ab Initio Modeling of fcc Fe-Co-Cr-Ni High Entropy Alloys with Full Composition Range

The Fe-Co-Cr-Ni quaternary system has been studied extensively in the past decade, not only because of the superior properties achieved like high tensile ductility and fracture toughness, but also it is the foundation for the development of FeCrCoNi-based HEAs. However, most of the investigations are mainly focusing on the equiatomic and semi-equiatomic compositions. The physical properties of non-equiatomic compositions are barely explored. In the current work, the ab initio approach is adopted to predict the lattice parameter, structure stabilities, elastic properties, and enthalpy of formations of fcc Fe-Cr-Co-Ni HEA single crystals with the special quasirandom structure (SQS) method. To expand the design of Fe-Co-Cr-Ni HEAs into a full composition range, the current simulations cover all the binaries, ternaries, and the whole quaternary system. The 2-D composition-property contour diagrams are created to show the physical properties in the ternary and quaternary systems. Furthermore, our investigation shows that the fcc alloys' lattice parameter increases with the addition of Fe and Cr and decreases with Ni and Co. In addition to the enthalpy of formation at o K, the shape distortion rate is proposed to be another essential parameter to evaluate crystal stability. The results show the addition of Cr would destabilize the fcc lattice and cause symmetry breaking. Finally, the result of Pugh’s ratio shows that most of the fcc alloys show ductile behavior (P > 1.75), especially for the alloys around Fe 3 Ni, FeCo, and Fe 2 NiCo (P > 2.5). The brittle behavior (P < 1.75) is located around Fe 3 Cr and Fe 2 CoCr. Meanwhile, Cr 2 NiCo and Cr 2 FeNiCo are considered promising compositions to be tried and verified experimentally because of the higher bulk modulus and moderate shear modulus.

36 MATERIALS SCIENCE↗

DOE OSTI2020

The lattice parameter – composition relationship of the body centered cubic uranium-niobium alloys

In this paper, in-situ time-of-flight neutron diffraction experiments were performed on uranium-niobium alloy with 6 wt% Nb to study the lattice parameter-composition relationship for the body centered cubic (bcc) alloys. Based on lattice-parameter measurements of Nb-supersaturated γs phase over the range of 450 – 790 °C, an improved Vegard's-type relationship was established for determination of Nb concentrations at elevated temperatures. Neutron diffraction data were also collected as a function of aging time over the 450 - 600 °C range when γs phase decomposed isothermally into the mixture of orthorhombic α-U and Nb-rich bcc phase, as well as at room-temperature on the alloys aged ex-situ at 500 °C up to five years. From these measurements, the average Nb concentrations in the bcc phase were determined based on the Rietveld refinements of weight fraction and mass conservation relations (lever rule). Over the 15at% – 78at% range of Nb concentrations that correspond to different experimental aging times, the lattice parameters at constant temperatures exhibit a nonlinear S-shaped variation with Nb concentration, and the associated excess volumes of mixing can be described by a subregular solution model of the Redlich–Kister type of polynomial. Over the full range of composition the S-shaped deviation from Vegard's law can be modeled using a combination of an elastic continuum model and a perturbation to the radii of the solute atoms in the solvent, suggesting that electronic interactions between solute and solvent atoms could play an important role in the compositional dependence of lattice parameter for the γ-phase U-Nb alloys. While Vegard's law is a straightforward and reasonably good approximation for the bcc solid solutions in the U-Nb system, the Nb concentrations determined from the weight fraction refinements of diffraction data provide internally consistent, mass-conserving estimates of solute redistribution for the monotectoid reaction.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Transferable predictions of energetic and structural properties for refractory solid solution alloys across chemical compositions

We present a data-efficient approach to train graph neural networks (GNNs) on density functional theory (DFT) data for accurate and transferable predictions of energetic and structural properties of refractory solid solution alloys in the niobium-tantalum-vanadium (Nb-Ta-V) chemical space. We start by training the GNN model only on DFT data that describes refractory binary alloys niobium-tantalum (Nb-Ta), niobium-vanadium (Nb-V), and tantalum-vanadium (Ta-V) to predict formation enthalpy and root mean squared displacement. Once trained, the GNN predictions are tested on DFT data describing refractory ternary alloys Nb-Ta-V. While, unsurprisingly, direct transferability from binary to ternary is not sufficiently accurate, augmenting the training with only 1% of the available ternary data (uniformly distributed across the entire range of chemical compositions) improves significantly the quality of the GNN predictions. For comparison, we assess the transferability in the opposite direction by training GNN models on ternary Nb-Ta-V data and making predictions on binaries Nb-Ta, Nb-V, and Ta-V, which exhibits notably higher predictive errors. The proposed methodology, which favors transferability from lower-component to higher-component alloys, offers an efficient path towards avoiding the curse of dimensionality incurred when collecting DFT data for discovery and design of multi-component disordered alloys.

Density functional theory calculations↗

DOE OSTI2022

Anomalous size effect on yield strength enabled by compositional heterogeneity in high-entropy alloy nanoparticles

High-entropy alloys (HEAs), although often presumed to be random solid solutions, have recently been shown to display nanometer-scale variations in the arrangements of their multiple chemical elements. Here, we study the effects of this compositional heterogeneity in HEAs on their mechanical properties using in situ compression testing in the transmission electron microscope (TEM), combined with molecular dynamics simulations. We report an anomalous size effect on the yield strength in HEAs, arising from such compositional heterogeneity. By progressively reducing the sample size, HEAs initially display the classical “smaller-is-stronger” phenomenon, similar to pure metals and conventional alloys. However, as the sample size is decreased below a critical characteristic length (~180 nm), influenced by the size-scale of compositional heterogeneity, a transition from homogeneous deformation to a heterogeneous distribution of planar slip is observed, coupled with an anomalous “smaller-is-weaker” size effect. Atomic-scale computational modeling shows these observations arise due to compositional fluctuations over a few nanometers. These results demonstrate the efficacy of influencing mechanical properties in HEAs through control of local compositional variations at the nanoscale.

36 MATERIALS SCIENCE↗

NASA NTRS1989

Measurement Of Composition In Transparent Model Alloy

Variation of FTIR technique developed to enable study of growth of cells of different solid phase in unidirectional solidification of these organic mixtures, which serve as transparent anologs of opaque monotectic metal alloys. Study of organic analogs expected to contribute to understanding of formation of aligned rods and particles in directional solidification of metal alloys. Advantage of technique is redistribution of material caused by solidification determined after fact, to very fine scale.

Kaukler, William F.↗

NASA NTRS1996

Smart Material Demonstrators Based on Shape Memory Alloys and Electroceramics

This paper describes the development and characterization of two technology demonstrators that were produced under the auspices of an ARPA sponsored smart materials synthesis and processing effort. The ARPA Smart Materials and Synthesis (SMS) Program was a 2 year, $10M partnership led by Martin Marietta Laboratories - Baltimore and included Lockheed Missiles & Space Co., NRL, AVX Corp., Martin Marietta Astronautics Groups, BDM Federal, Inc., Virginia Tech, Clemson, University of Maryland, Denver University, and The Johns Hopkins University. In order to demonstrate the usefulness of magnetron sputtered shape memory foil and the manufacturability of reliable, reproducible electrostrictive actuators, the team designed a broadband active vibration cancellation device for suppressing the vibration load on delicate instruments and precision pointing devices mounted on orbiting satellites and spacecraft. The results of extensive device characterization and bench testing are discussed. Initial simulation results show excellent control authority and amplitude attenuation over the range of anticipated disturbance frequencies. The SMS Team has also developed an active 1-3 composite comprising micro-electrostrictive actuators embedded in a polymeric matrix suitable for underwater applications such as sonar quieting and listening arrays, and for medical imaging. Follow-on programs employing these technologies are also described.

Cooke, Arther V.↗

DOE OSTI2020

Rapid assessment of structural and compositional changes during early stages of zirconium alloy oxidation

A multimodal chemical imaging approach has been developed and applied to detail the dynamic, atomic-scale changes associated with oxidation of a zirconium alloy (Zircaloy-4). Scanning transmission electron microscopy, a gas-phase reactor chamber attached to an atom probe tomography instrument, and synchrotron-based X-ray absorption near-edge spectroscopy were employed to reveal morphology, composition, crystal, and electronic structure changes that occur during initial stages of oxidation at 300 °C. Oxidation was carried out in 10 mbar O 2 gas for short exposure times of 1 and 5 min. A multilayered oxide film with a cubic ZrO adjacent to the oxide/metal interface, a nanoscopic transition region with a graded composition of ZrO 2-x (where 0 < x < 1), and tetragonal ZrO 2 in the outermost oxide were formed. Partitioning of the major alloying element (tin) to the oxide/metal interface and heterogeneously within the oxide accompanied the development of the layered oxide. Our work provides a rapid, high-throughput approach for detailed characterisation of initial stages of zirconium alloy oxidation at an accelerated time scale, with implications for several other alloy systems.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Chemical composition of material extractives influences microbial growth and dynamics on wetted wood materials

The impact of material chemical composition on microbial growth on building materials remains relatively poorly understood. We investigate the influence of the chemical composition of material extractives on microbial growth and community dynamics on 30 different wood species that were naturally inoculated, wetted, and held at high humidity for several weeks. Microbial growth was assessed by visual assessment and molecular sequencing. Unwetted material powders and microbial swab samples were analyzed using reverse phase liquid chromatography with tandem mass spectrometry. Different wood species demonstrated varying susceptibility to microbial growth after 3 weeks and visible coverage and fungal qPCR concentrations were correlated (R 2 = 0.55). Aspergillaceae was most abundant across all samples; Meruliaceae was more prevalent on 8 materials with the highest visible microbial growth. A larger and more diverse set of compounds was detected from the wood shavings compared to the microbial swabs, indicating a complex and heterogeneous chemical composition within wood types. Several individual compounds putatively identified in wood samples showed statistically significant, near-monotonic associations with microbial growth, including C 11 H 16 O 4 , C 18 H 34 O 4 , and C 6 H 15 NO. A pilot experiment confirmed the inhibitory effects of dosing a sample of wood materials with varying concentrations of liquid C 6 H 15 NO (assuming it presented as Diethylethanolamine).

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2022

Corresponding Standard Reference Material Data used in Partial Least Squares Regression Models for Sugar Composition Estimates in Biomass in: Economic Impact of Yield and Composition Variation in Bioenergy Crops: Populus trichocarpa

Corresponding Standard Reference Material Data used in Partial Least Squares Regression Models for Sugar Composition Estimates in Biomass in: Economic Impact of Yield and Composition Variation in Bioenergy Crops: Populus trichocarpa (for corresponding manuscript: DOI: 10.1002/bbb.2148) PDF Files: Images of 1H NMR spectra for neutralized 2-stage acid hydrolysates of 4 NIST Standard Reference Material biomass samples (Monterey Pine 8493, Sugarcane Bagasse 8491, Wheat Straw 8494, and Eastern Cottonwood/Poplar 8492) and 2 Center for Bioenergy Innovation reference biomass samples (Poplar - Populus trichocarpa and Switchgrass - Panicum Virgatum). Suppression of the water peak was achieved using a NOESY-1D with presaturation, a recycle delay of 5 s, and a total of 64 scans. Spectra were acquired at 298 K and processed with automatic phase correction, baseline correction, and chemical shift referencing to TSP-d4. Images show all 1H data from 10 to 1ppm with inset spectra of region of interest (4.0 to 3.1 ppm). Text Files: Spectra for neutralized 2-stage acid hydrolysates of 4 NIST Standard Reference Material biomass samples (Monterey Pine 8493, Sugarcane Bagasse 8491, Wheat Straw 8494, and Eastern Cottonwood/Poplar 8492) and 2 Center for Bioenergy Innovation reference biomass samples (Poplar - Populus trichocarpa and Switchgrass - Panicum Virgatum) were converted into text files for plotting. Files contain 8192 points of raw spectral data from 12.23 to -2.78 ppm. The text file contains 4 columns of data and includes: Point number, Intensity, Hz, and ppm. Xcel Spreadsheet: HPLC measured monomeric sugar concentrations and bucketed 1H NMR data used to build monomeric sugar composition prediction models. Sugar composition in biomass determined from HPLC analyses are given in mg sugar/mg of biomass. Spectral bucketing was performed using Bruker’s AMIX software. Spectra were divided into 0.005 ppm buckets in the region of 3.10– 4.15 ppm for a total of 210 buckets. Headers for the bucketed data are the chemical shift in ppm of the center of the bucket. Bucketed data was used to build partial least squares models for subsequent predictions in The Unscrambler v. 10.5(CAMO A/S, Trondheim, Norway). The formation of methanol during hydrolysis interferes with the quantitative NMR analysis of sugars, so the methanol peak centered at 3.37 ppm and spanning four buckets (3.2925 – 3.2775 ppm) was set to zero for all spectra.

09 BIOMASS FUELS↗

NASA NTRS1980

Composite materials research and education program: The NASA-Virginia Tech composites program

Major areas of study include: (1) edge effects in finite width laminated composites subjected to mechanical, thermal and hygroscopic loading with temperature dependent material properties and the influence of edge effects on the initiation of failure; (2) shear and compression testing of composite materials at room and elevated temperatures; (3) optical techniques for precise measurement of coefficients of thermal expansion of composites; (4) models for the nonlinear behavior of composites including material nonlinearity and damage accumulation and verification of the models under biaxial loading; (5) compressive failure of graphite/epoxy plates with circular holes and the buckling of composite cylinders under combined compression and torsion; (6) nonlinear mechanical properties of borsic/aluminum, graphite/polyimide and boron/aluminum; (7) the strength characteristics of spliced sandwich panels; and (8) curved graphite/epoxy panels subjected to internal pressure.

Herakovich, C. T.↗