Batteries & storage — Page 41 | Engineering Papers

NASA NTRS2000

Design of a 10.8 kWh, 28V Ni-MH Battery Using Commercial Ni-MH Cells

This paper describes the design of a 10.8 kWh, 28V, Ni-MH battery using commercial off-the shelf (COTS) 4/3A Ni-MH cells for the X-38 vehicle, an experimental version of the Crew Return Vehicle (CRY). This will be an autonomous vehicle that will enable International Space Station crews to return to earth in the event of a medical, or other, emergency. The X-38 will be powered by 3 batteries: a 32 V primary battery, which will power the vehicle avionics for up to 7 hours for a loiter and de-orbit phase of the descent; a 28 V Ni-MH battery which will take over for the primary battery after de-orbit until landing, and a 270V Ni-Cd battery, which will be used to power electromechanical actuators and the winches controlling a parachute for landing.

Hellen, Robert M.↗

NASA NTRS2014

Battery Cell Balancing System and Method

A battery cell balancing system is operable to utilize a relatively small number of transformers interconnected with a battery having a plurality of battery cells to selectively charge the battery cells. Windings of the transformers are simultaneously driven with a plurality of waveforms whereupon selected battery cells or groups of cells are selected and charged. A transformer drive circuit is operable to selectively vary the waveforms to thereby vary a weighted voltage associated with each of the battery cells.

Davies, Francis J.↗

NASA NTRS2017

Assessment of lnternational Space Station (ISS) Lithium-ion Battery Thermal Runaway (TR)

This task was developed in the wake of the Boeing 787 Dreamliner lithium-ion battery TR incidents of January 2013 and January 2014. The Electrical Power Technical Discipline Team supported the Dreamliner investigations and has followed up by applying lessons learned to conduct an introspective evaluation of NASA's risk of similar incidents in its own lithium-ion battery deployments. This activity has demonstrated that historically NASA, like Boeing and others in the aerospace industry, has emphasized the prevention of TR in a single cell within the battery (e.g., cell screening) but has not considered TR severity-reducing measures in the event of a single-cell TR event. center dotIn the recent update of the battery safety standard (JSC 20793) to address this paradigm shift, the NASA community included requirements for assessing TR severity and identifying simple, low-cost severity reduction measures. This task will serve as a pathfinder for meeting those requirements and will specifically look at a number of different lithium-ion batteries currently in the design pipeline within the ISS Program batteries that, should they fail in a Dreamliner-like incident, could result in catastrophic consequences. This test is an abuse test to understand the heat transfer properties of the cell and ORU in thermal runaway, with radiant barriers in place in a flight like test in on orbit conditions. This includes studying the heat flow and distribution in the ORU. This data will be used to validate the thermal runaway analysis. This test does not cover the ambient pressure case. center dotThere is no pass/ fail criteria for this test.

Graika, Jason↗

NASA NTRS2018

Design and Development of Advanced Air-Cathodes for Li-Air Battery

NASA's future missions demand high energy density batteries. Current state-of-the-art lithium-ion batteries (LIBs) reach the specific energy capacity limits (<250 Wh/kg), thus new electrochemical storage technologies are needed to meet NASA's future mission requirement of >400 Wh/kg. Battery chemistries with higher theoretical energy densities in particular, Li-metal based battery chemistries such as Li-air, are being actively pursued, but there remains a number of issues to be solved. Development of advanced and optimized air cathodes will be crucial for improving capacity retention and cycle life of Li-air battery. The microstructure of carbon substrates and the catalytic oxygen reduction of the air-cathode play critical roles in the electrochemical performance in Li-air batteries. With the development and proper design of air cathodes, the energy efficiency and energy density can be enhanced significantly. In this presentation, the results of advanced permeable air cathodes design with different substrates such as 2D carbon paper or carbon cloth, vs 3D graphene or metal foam, different high surface area carbon materials and incorporation with catalysts on oxygen reduction reactions, different porosity controlling of air cathode as well the additives in electrolyte will be presented. The cycling and rate capability performance of these air-cathodes in the Li-air cells will be discussed as well.

Wu, James J.↗

NASA NTRS2019

Prognostics and Health Monitoring in Li-Ion Batteries and Capacitors Using Physics-Based Modeling Approach

In order to tackle and solve the prediction problem of the lifetime of Li-ion batteries, it is essential to have awareness of the current state and health of the battery pack. To be able to accurately predict the future state of any system, one must possess knowledge of its current and future operations. Using derived models of the current and future system behavior, a model-based prognostics approach can be implemented as a solution to the prediction problem. As more and more autonomous electric vehicles progressively emerge in our daily life, a very critical challenge lies in accurate prediction of remaining useful life of the systems/subsystems. Batteries, power electronics conditioning systems, and motors are integrated to form the powertrain in electric vehicles; one of the most critical systems. In the case of electric aircrafts, computing remaining flying time is critical for safety, since an aircraft that runs out of power (battery charge) while in the air will eventually lose control leading to catastropheThis presentation covers a physics-based modeling approach implemented for case studies in capacitor and battery prognostics which are an integral part of an electrical powertrain system. The general approach of model-based prognostics will be examined as a potential solution for safety critical problems related to battery state of charge and state of health.

Physics based modeling↗

NASA NTRSDate not supplied

Thermal-Fluid Analysis of a Liquid-Cooled Battery Module for Electrified Aircraft

The development of safe, energy-dense batteries is critical to advancing hybrid electric and fully electrified aircraft propulsion. Achieving this capability requires a thermal management system that can maintain battery performance and safety under demanding operational conditions. The objective of this project is to support the maturation of next-generation lithium-ion batteries for electrified aircraft by conducting performance testing on integrated battery modules, specifically a 2-cell series configuration module housed within an aluminum enclosure. Designed to operate at a nominal 7.2 V with discharge rates up to 2.5C, the module will eventually be used to power an electric motor and DC-DC converter, generating substantial thermal loads that must be effectively managed to increase the usable energy and power density of electrified aircraft. To address these thermal challenges, this study presents the development and thermal-fluid analysis of a liquid-cooled thermal management system. While the full aircraft architecture utilizes an eight-string configuration, the present work evaluates a representative single-string water coolant loop to characterize baseline performance. The active cooling loop circulates water through a reservoir, pump, the battery module, and a variable area flow meter. Key performance metrics including component-level temperatures, mass flow rates, and pressure drops are quantified across the loop. Across discharge rates ranging from 0.5C to 2.5C, the active thermal loop consistently and effectively removed heat from the module, validating the design approach and confirming readiness for further development. The validated thermal performance indicates a path toward scalable battery modules that could enable energy and power dense systems for hybrid electric aircraft.

Electrified Aircraft↗

DOE OSTI2020

Protective anode coatings for high energy batteries

Materials for coating a metal anode in a high energy battery, anodes coated with the materials, and batteries incorporating the coated anodes are provided. Also provided are batteries that utilize the materials as electrolytes. The coatings, which are composed of binary, ternary, and higher order metal and/or metalloid oxides, nitrides, fluorides, chlorides, bromides, sulfides, and carbides limit the reactions between the electrolyte and the metal anode in a battery, thereby improving the performance of the battery, relative to a battery that employs a bare anode.

Hegde, Vinay Ishwar↗

DOE OSTI2022

Flow battery cleansing cycle to maintain electrolyte health and system performance

A method of cleansing a redox flow battery system may include operating the redox flow battery system in a charge, discharge, or idle mode, and responsive to a redox flow battery capacity being less than a threshold battery capacity, mixing the positive electrolyte with the negative electrolyte. In this way, battery capacity degradation following cyclic charging and discharging of the redox flow battery system can be substantially reduced.

Song, Yang↗

DOE OSTI2022

Protective anode coatings for high energy batteries

Materials for coating a metal anode in a high energy battery, anodes coated with the materials, and batteries incorporating the coated anodes are provided. Also provided are batteries that utilize the materials as electrolytes. The coatings, which are composed of binary, ternary, and higher order metal and/or metalloid oxides, nitrides, fluorides, chlorides, bromides, sulfides, and carbides limit the reactions between the electrolyte and the metal anode in a battery, thereby improving the performance of the battery, relative to a battery that employs a bare anode.

Hegde, Vinay Ishwar↗

DOE OSTI2023

State of battery health estimation based on swelling characteristics

There is disclosed an electrical device including a battery, and a battery management system. The battery management system includes a controller in electrical communication with a pressure sensor to monitor the state of health of the battery. The controller applies a method for determining the state of health that uses a non-electrical (mechanical) signal of force measurements combined with incremental capacity analysis to estimate the capacity fading and other health indicators of the battery with better precision than existing methods. The pressure sensor may provide the force measurement signal to the controller, which may determine which incremental capacity curve based on force to use for the particular battery. The controller then executes a program utilizing the data from the pressure sensor and the stored incremental capacity curves based on force to estimate the capacity fading and signal a user with the state of health percentage.

Stefanopoulou, Anna G.↗

DOE OSTI2023

Quinones having high capacity retention for use as electrolytes in aqueous redox flow batteries

We disclose quinone compounds and related species (Formula I) that possess significant advantages when used as a redox active material in a battery, e.g., a redox flow battery. In particular, the compounds provide redox flow batteries (RFBs) with extremely high capacity retention. For example, RFBs of the invention can be cycled for 500 times with negligible loss of capacity, and such batteries could be employed for years of service. Thus, the invention provides a high efficiency, long cycle life redox flow battery with reasonable power cost, low energy cost, and all the energy scaling advantages of a flow battery.

Aziz, Michael J.↗

DOE OSTI2023

Coordinated Wind Power Plant and Battery Control for Active Power Services

This article considers joint active power control of wind turbines and battery storage to follow a plant-level power reference signal. The joint control dynamically curtails the energy from a subset of the wind turbines and stores or withdraws energy from the battery to meet the power reference setpoint while accounting for wind plant aerodynamic interactions, such as wake losses. As a use case, we study the performance of the controller in maintaining a constant power output over hourly periods. A wind plant operating in this way would rely much less on other grid resources to meet its contractual agreements, thereby improving grid reliability, especially in grids with high penetration of wind and solar generation. We compare the operation of the wind plant under joint active power control to standard power-maximizing control with battery support. We present an analysis of the performance of the control system architecture. To study the impact of the battery size on performance, we simulate a 50-MW wind plant supported by batteries ranging from 8 to 64?MWh. We then evaluate the over and undergeneration penalties incurred by the plant during the simulation period.

17 WIND ENERGY↗

DOE OSTI2020

Time-of-Use and Demand Charge Battery Controller Using Stochastic Model Predictive Control

Stationary batteries in residential and commercial buildings are often used to smooth customer load profiles and to lower customer electricity bills. Controllers for these battery systems should account for customer energy consumption, rate structures, and high internal battery temperatures, which can lead to reduced performance over the battery lifetime. It is important to consider the uncertainty in forecasting energy consumption and temperature, especially for customers with highly variable and uncertain loads. We propose a novel battery controller using stochastic model predictive control that accounts for these uncertainties and can handle complex rate structures, including demand charges. We show that the controller performs better than standard model predictive control when there is significant uncertainty in the forecast. We also show improvements in the performance with more accurate forecasts and with a more aggressive control strategy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRSDate not supplied

Practical Battery Thermal Modeling Techniques

Lithium-ion batteries are thermo-electrochemical devices, whereby nearly every facet of their functionality and performance are thermally driven. As a result, it is important to have thermal modeling techniques that effectively capture the intricacies of both the electrochemical nature of the battery and also the complex thermal network that typically results from the design of the battery thermal management system. Here we present a thermal modeling workflow and a set of general assumptions for how to construct a thermal model of a Li-ion battery pack. We use a 14-cell bank of 18650-format Li-ion cells, loosely based on a proposed alternative battery design for Orion, as the example. Although the workflow is performed with Thermal Desktop and related utilities, the focus of this presentation is less about software specific techniques, but rather is focused on the assumptions and conditions that should be used in a model (regardless of the tool used to build the model). Example cases and results will be presented for charge, discharge, and thermal runaway.

lithium-ion battery↗

NASA NTRSDate not supplied

Thermal Data-driven Model Reduction for Enhanced Battery Health Monitoring

Electric aviation faces a major challenge of avoiding potentially catastrophic consequences of the battery’s thermal runaway while keeping the weight of the battery low. Detection of early warning signals of battery failures requires accurate monitoring of the battery’s health throughout its lifespan. However, identifying the parameters of the battery from field data is notoriously difficult. We investigate this problem within the framework of modeling the temperature dynamics of a Li-ion cell during tests simulating loading in electric aircraft flights. It is found that the parameters of a higher-fidelity physics-based thermal model cannot be identified from the simulated flight data. To resolve this issue, we reduce the higher-fidelity thermal model to a model with fewer parameters. The resulting reduced-order model can predict temperature dynamics accurately and is identifiable throughout the cell’s lifespan which allows using the model’s parameters to monitor the state-of-health of the aging cell and detect anomalies in thermal behavior.

Li ion batteries↗

DOE OSTI2020

Time-of-Use and Demand Charge Battery Controller Using Stochastic Model Predictive Control: Preprint

Stationary batteries in residential and commercial buildings are often used to smooth customer load profiles and to lower customer electricity bills. Controllers for these battery systems should account for customer energy consumption, rate structures, and high internal battery temperatures, which can lead to reduced performance over the battery lifetime. It is important to consider the uncertainty in forecasting energy consumption and temperature, especially for customers with highly variable and uncertain loads. We propose a novel battery controller using stochastic model predictive control that accounts for these uncertainties and can handle complex rate structures, including demand charges. We show that the controller performs better than standard model predictive control when there is significant uncertainty in the forecast. We also show improvements in the performance with more accurate forecasts and with a more aggressive control strategy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Battery Control Using Stochastic Model Predictive Control

Stationary batteries in residential and commercial buildings are often used to smooth customer load profiles and to lower customer electricity bills. Controllers for these battery systems should account for customer energy consumption, rate structures, and high internal battery temperatures, which can lead to reduced performance over the battery lifetime. It is important to consider the uncertainty in forecasting energy consumption and temperature, especially for customers with highly variable and uncertain loads. We propose a novel battery controller using stochastic model predictive control that accounts for these uncertainties and can handle complex rate structures, including demand charges. We show that the controller performs better than standard model predictive control when there is significant uncertainty in the forecast. We also show improvements in the performance with more accurate forecasts and with a more aggressive control strategy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Heuristic Dispatch Based on Price Signals for Behind-the-Meter PV-Battery Systems in the System Advisor Model

The economic potential of a behind-the-meter (BTM) PV-battery system depends greatly on how the battery is dispatched. Different utility rates, system sizes, generation and load profiles can all require different dispatch strategies. This paper presents price signals dispatch, a new algorithm for automated economic dispatch of BTM PV-battery systems, which utilizes 24-hour PV and load forecasts, degradation data, and utility rates. The algorithm is integrated with the System Advisor Model (SAM) tool and is tested with a nonlinear generic electrochemical battery model. Price signals dispatch outperforms SAM’s existing algorithms in cases requiring a balance between demand charge management and energy arbitrage, and in cases where battery degradation imposes a significant cost.

41 EE - Solar Energy Technologies Office (EE-4S)↗