Engineering Papers⌕ Search

Engineering topics

deVelder, Nathaniel

Publications and source records attributed to deVelder, Nathaniel.

9 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Design of a Preliminary Family of Airfoils for High Reynolds Number Wind Turbine Applications

For the past 30 years, offshore wind turbines exhibited a continual pattern of growth that is expected to continue as the industry pushes for higher efficiency. Current designs for the next generation of wind turbines are so large that the chordwise Reynolds number of the blades is well beyond the design range of existing open-source airfoil families. This paper presents a preliminary family of new airfoils designed specifically for the needs of these next-generation offshore turbines, ranging from 21% thick to 30% thick with operating Reynolds numbers between 12 million and 18 million. These airfoils are intended to be alternative to the FFA airfoils that are commonly used on reference turbines such as the IEA 15MW and 22MW designs. In this work, airfoil performance metrics and design targets are developed, the design process is outlined, an optimization scheme is presented, and finally the airfoils and their simulated performance are compared to existing baselines. Lift to drag ratios in a clean condition were improved by up to 49.3% from the baseline FFA airfoil, and rough condition lift to drag ratio was improved by up to 9.3%. It is estimated that the cumulative improvements provided by this airfoil family would result in an approximately 1% increase of Annual Expected Power (AEP) for the 22 MW turbine compared to the current baseline.

airfoils↗
DOE OSTI2024

Modification of wind turbine wakes by large-scale, convective atmospheric boundary layer structures

In this study, we consider the impact of large-scale, convective structures in an unstable atmospheric boundary layer on wind turbine wakes. Simulation data from a high-fidelity large-eddy simulation (LES) of the AWAKEN wind farm site matching unstable atmospheric conditions were analyzed, and both turbine performance and wake behavior were affected based on their location relative to the convective structures. Turbines located in updraft regions of the flow experienced lower inflow velocity and generated less power, but their wakes were observed to recover faster and saw greater turbulent kinetic energy mixing higher in the boundary layer. The opposite effect was found for turbines in the downdraft regions of the convective structures. A simplified model of this wake behavior was also developed based on a two-dimensional k–ε Reynolds-Averaged Navier–Stokes formulation. This simplified model included the effects of vertical transport, but could be efficiently solved as a parabolic system, and was found to capture similar wake modifications observed in the high-fidelity LES computations.

16 TIDAL AND WAVE POWER↗
DOE OSTI2024

A Green's Function Wind Turbine Induction Model That Incorporates Complex Inflow Conditions

ABSTRACT In this work, we develop a new analytical turbine induction model that can incorporate complex inflow conditions including cases where the wind velocity and temperature profiles can vary as functions of height. This induction model is derived from the linearized Navier–Stokes and leads to a second‐order ODE that can be solved using a Green's function formulation. The corresponding Green's function for several configurations are found including the infinite domain, semi‐infinite domain with ground plane, and a power law velocity inflow profile. The results of this approach are then compared with simulations of the turbine induction field using the AMR‐Wind CFD solver with a uniformly loaded actuator disk model. These comparisons show that the Green's function approach captures the centerline blockage, three‐dimensional blockage flow field, and streamwise velocity slow down, with very good agreement for lower thrust conditions and at larger distances away from rotor disk. The effects of shear on the turbine blockage were also compared using a power law inflow profile, and we show that this approach matches the CFD predictions for the cases considered.

17 WIND ENERGY↗
DOE OSTI2024

One-to-one aeroservoelastic validation of operational loads and performance of a 2.8 MW wind turbine model in OpenFAST

Abstract. This article presents a validation study of the popular aeroservoelastic code suite OpenFAST leveraging weeks of measurements obtained during normal operation of a 2.8 MW land-based wind turbine. Measured wind conditions were used to generate one-to-one turbulent flow fields (i.e., comparing simulation to measurement in 10 min increments, or bins) through unconstrained and constrained assimilation methods using the kinematic turbulence generators TurbSim and PyConTurb. A total of 253 bins of 10 min of normal turbine operation were selected for analysis, and a statistical comparison in terms of performance and loads is presented. We show that successful validation of the model was not strongly dependent on the type of inflow assimilation method used for mean quantities of interest, which had median modeling errors per wind-speed interval generally within 5 %–10 % of the measurement. The type of inflow assimilation method did have a larger effect on the fatigue predictions for blade-root flapwise and tower-base fore–aft quantities, which surprisingly saw larger errors from the assumed higher-fidelity assimilation methods. Avenues for further work are discussed and include possible improvements to the aerodynamic, structural, and controller modeling that may offer insight on the origin of the up to ∼ 40 % median overprediction of fatigue for these quantities.

17 WIND ENERGY↗
DOE OSTI2024

Enabling "Fuel" Switching through On-Demand Wind Control

This work demonstrates that classical shear-flow stability theory can be successfully applied to modify wind turbine wakes and also explains the success of several emerging, empirically-arrived control methods (i.e., dynamic induction and helix control). Linear stability theory predictions are extended to include the effects of non-axisymmetric inflow profiles, such as wind shear, which is shown to not strongly affect the primary forcing frequency. The predictions, as well as idealized large-eddy simulations using actuator-line representation of the turbine blades, agree that the n = 0 and ±1 modes have faster initial growth rates than higher-order modes, suggesting the lower-order modes are more appropriate for wake control. Exciting the lower-order modes with periodic pitching of the blades produces higher entrainment into the wake and consequently faster wake recovery.

17 WIND ENERGY↗