Engineering Papers⌕ Search

Engineering topics

Zlobin, A V

Publications and source records attributed to Zlobin, A V.

At least 19 records

High-Field Combined-Function Magnets for a 1.5 x 1.5 TeV Muon Collider Storage Ring

Designs and parameters of dipoles and combined-function quadrupoles for bending arc lattice of a 1.5x1.5 TeV muon collider with an average luminosity of 4x1034 cm{sup -2}s{sup -1} are presented. The magnets use the Nb{sub 3}Sn superconductor and provide the required gradients and fields with the appropriate operating margins and field quality. The magnet apertures accommodate tungsten liners to minimize the dynamic heat load in the superconducting coils.

43 PARTICLE ACCELERATORS↗

Helical Muon Beam Cooling Channel Engineering Design

The Helical Cooling Channel (HCC), a novel technique for six-dimensional (6D) ionization cooling of muon beams, has shown considerable promise based on analytic and simulation studies. However, the implementation of this revolutionary method of muon cooling requires new techniques for the integration of hydrogen-pressurized, high-power RF cavities into the low-temperature superconducting magnets of the HCC. We present the progress toward a conceptual design for the integration of 805 MHz RF cavities into a 10 T Nb{sub 3}Sn based HCC test section. We include discussions on the pressure and thermal barriers needed within the cryostat to maintain operation of the magnet at 4.2 K while operating the RF and energy absorber at a higher temperature. Additionally, we include progress on the Nb{sub 3}Sn helical solenoid design.

43 PARTICLE ACCELERATORS↗

Development and Fabrication of Nb3Sn Rutherford Cable for the 11 T DS Dipole Demonstration Model

Fermilab and CERN started the development of 11 T 11-m long Nb{sub 3}Sn dipoles to replace few regular LHC NbTi dipoles and free space for cold collimators in LHC DS areas. An important step in the design of these magnets is the development of the high aspect ratio Nb{sub 3}Sn cable to achieve the nominal field of 11 T at the nominal LHC operating current of 11.85 kA with 20% margin. The keystoned cables 14.7 mm wide with and without a stainless steel core were made out of hard Cu wires and Nb{sub 3}Sn RRP strand 0.7 mm nominal diameter. The cable optimization process was aimed at achieving both mechanical stability and minimal damage to the delicate internal architecture of the Restacked-Rod-Process (RRP) Nb{sub 3}Sn strands with 127 restack design to be used in the magnet short models. Each cable was characterized electrically for transport properties degradation at high field and for low field stability, and metallographically for internal damage.

36 MATERIALS SCIENCE↗

Design and Fabrication of a Single-Aperture 11T Nb3Sn Dipole Model for LHC Upgrades

The planned upgrade of the LHC collimation system includes additional collimators to be installed in the dispersion suppressor areas of points 2, 3 and 7. To provide the necessary longitudinal space for the collimators, a replacement of 8.33 T Nb-Ti LHC main dipoles with 11 T dipoles based on Nb{sub 3}Sn superconductor compatible with the LHC lattice and main systems is being considered. To demonstrate this possibility FNAL and CERN have started a joint program to develop a 2 m long single-aperture dipole magnet with the nominal field of 11 T at {approx}11.85 kA current and 60 mm bore. This paper describes the demonstrator magnet magnetic and mechanical designs and analysis, coil fabrication procedure. The Nb{sub 3}Sn strand and cable parameters and test results are also reported.

43 PARTICLE ACCELERATORS↗

Radiation and Thermal Analysis of Superconducting Quadrupoles in the Interaction Region of Linear Collider

Radiation heat deposition in the superconducting magnets of the Interaction Region (IR) of a linear collider can be a serious issue that limits the magnet operating margins and shortens the material lifetime. Radiation and thermal analyses of the IR quadrupoles in the incoming and extraction beam lines of the ILC are performed in order to determine the magnet limits. This paper presents an analysis of the radial, azimuthal and longitudinal distributions of heat deposition in the incoming and disrupted beam doublets. Operation margins of the magnets based on NbTi superconductor are calculated and compared. The radiation and thermal analysis of the ILC IR quadrupoles based on Rutherford type cables was performed. It was found that the peak radiation heat deposition takes place in the second extraction quadrupole QFEX2. The maximum power density in the coil is {approx}17mW/g. This is rather high, comparing to the proton machines (LHC). However, the fast radial decay of the heat deposition together with the high thermal conductivity of the Rutherford type cable limits the coil temperatures to a moderate level. It was determined that both 2-layer and 4-layer QFEX2 magnet designs have thermal margins of a factor of {approx}4 at the nominal gradient of 31.3 T/m. Because of the large margins, these magnets can easily accommodate possible changes in the IR optics and heat deposition levels.

43 PARTICLE ACCELERATORS↗

Test Results of 15 T Nb3Sn Quadrupole Magnet HQ01 with a 120 mm Bore for the LHC Luminosity Upgrade

In support of the luminosity upgrade of the Large Hadron Collider (LHC), the US LHC Accelerator Research Program (LARP) has been developing a 1-meter long, 120 mm bore Nb{sub 3}Sn IR quadrupole magnet (HQ). With a short sample gradient of 219 T/m at 1.9 K and a conductor peak field of 15 T, the magnet will operate under higher forces and stored-energy levels than that of any previous LARP magnet models. In addition, HQ has been designed to incorporate accelerator quality features such as precise coil alignment and adequate cooling. The first 6 coils (out of the 8 fabricated so far) have been assembled and used in two separate tests-HQ01a and HQ01b. This paper presents design parameters, summary of the assemblies, the mechanical behavior as well as the performance of HQ01a and HQ01b.

43 PARTICLE ACCELERATORS↗