Engineering topics

Zhou, Shiyuan

Publications and source records attributed to Zhou, Shiyuan.

8 records

DOE OSTI2024

Tailoring-Orientated Deposition of Li 2 S for Extreme Fast-Charging Lithium–Sulfur Batteries

Precipitation/dissolution of insulating Li 2 S has long been recognized as the rate-determining step in lithium-sulfur (Li-S) batteries, which dramatically undermines sulfur utilization at elevated charging rates. Herein, we present an orientated Li 2 S deposition strategy to achieve extreme fast charging (XFC, ≤15 min) through synergistic control of porosity, electronic conductivity, and anchoring sites of electrode substrate. Via magnesiothermic reduction of a zeolitic imidazolate framework, a nitrogen-doped and hierarchical porous carbon with highly graphitic phase was developed. This design effectively reduces interfacial resistance and ensures efficient sequestration of polysulfides during deposition, leading to (110)-preferred growth of Li 2 S nanocrystalline between (002)-dominated graphitic layers. Our approach directs an alternative Li 2 S deposition pathway to the commonly reported lateral growth and 3D thickening growth mode, ameliorating the electrode passivation. Therefore, a Li-S cell capable of charging/discharging at 5C (12 min) while maintaining excellent cycling stability (82% capacity retention) for 1000 cycles is demonstrated. In conclusion, even under high S loading (8.3 mg cm -2 ) and low electrolyte/sulfur ratio (3.8 mL mg -1 ), the sulfur cathode still delivers a high areal capacity of >7 mAh cm -2 for 80 cycles.

25 ENERGY STORAGE↗

DOE OSTI2024

Polysulfide-incompatible additive suppresses spatial reaction heterogeneity of Li-S batteries

Rational electrolyte engineering for practical pouch cells remains elusive because the correlation between the cathode/solid-electrolyte interphase layer and cell-level reaction behavior is poorly understood. Here, by combining multiscale characterization and computational modeling, we show that—counter to the conventional perception of polysulfide-incompatible additives—the spontaneous reaction of sparingly solvated polysulfides with Lewis acid additives (LAAs) can induce in situ formation of a homogeneous interphase on thick and tortuous S cathode. Multiscale synchrotron X-ray characterization consistently affirms that such interface design could effectively eliminate the notorious problems of polysulfide shuttle and lithium corrosion and, more importantly, provide an interconnected “ion transport highway” to alleviate the uneven ion transport within the tortuous S cathode. Hence, this design dramatically reduces the reaction heterogeneity of lithium-sulfur (Li-S) pouch cells under lean electrolyte conditions. Further, this work resolves controversy around the role of polysulfide-incompatible additives in high-energy Li-S pouch cells and highlights the importance of suppressing reaction heterogeneity for practical batteries.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Sustainable layered cathode with suppressed phase transition for long-life sodium-ion batteries

Sodium-ion batteries are among the most promising alternatives to lithium-based technologies for grid and other energy storage applications due to their cost benefits and sustainable resource supply. For the cathode—the component that largely determines the energy density of a sodium-ion battery cell—one major category of materials is P2-type layered oxides. Unfortunately, at high state-of-charge, such materials tend to undergo a phase transition with a very large volume change and consequent structural degradation during long-term cycling. Here we address this issue by introducing vacancies into the transition metal layer of P2-Na$_{0.7}$Fe$_{0.1}$Mn$_{0.75\square}$$_{0.15}$O2 (‘$_{\square}$’ represents a vacancy). The transition metal vacancy serves to suppress migration of neighbouring Na ions and therefore maintain structural and thermal stability in Na-depleted states. Moreover, the specific Na-O-$_{\square}$ configuration triggers a reversible anionic redox reaction and boosts the energy density. As a result, the cathode design here enables pouch cells with energy densities of 170 Wh kg -1 and 120 Wh kg -1 that can operate for over 600 and 1,000 cycles, respectively. In conclusion, our work not only suggests a feasible strategy for cathode design but also confirms the possibility of developing a battery chemistry that features a reduced need for critical raw materials.

25 ENERGY STORAGE↗

DOE OSTI2024

Achieving a high-performance sodium-ion pouch cell by regulating intergrowth structures in a layered oxide cathode with anionic redox

In P2-type layered transition metal (TM) oxides, which are typical cathode materials for Na-ion batteries, the presence of Li within the TM layer could lead to the formation of specific Na–O–Li configurations that trigger additional oxygen redox at high charging voltages. However, the prismatic-type (P-type) to octahedral-type (O-type) phase transition and irreversible TM migration could be simultaneously aggravated in high state of charge, resulting in structural distortion. Here we demonstrate that excessive desodiation of P2-Na 0.67 Li 0.1 Fe 0.37 Mn 0.53 O 2 (NLFMO) induces the formation of neighbouring O-type stacking faults with an intergrowth structure (that is, interlacing of O- and P-type layers), which leads to out-of-lattice Li migration and irreversible oxygen loss. We show that, by controlling the depth of charge to tailor the intergrowth structure, a P-type stacking state can be uniformly interspersed between the O-type stacking state, thereby avoiding neighbouring O-type stacking faults. Adjusting the O/P intergrowth structure leads to both reversible migration of Li/TM ions and reversible anionic redox in the NLFMO cathode. In conclusion, we thereby achieve a high-performance pouch cell (with an energy density of 165 W h kg −1 based on the entire weight of the cell) with both cationic and anionic redox activities.

25 ENERGY STORAGE↗

DOE OSTI2023

Visualizing interfacial collective reaction behaviour of Li–S batteries

Benefiting from high energy density (2,600 Wh kg -1 )) and low cost, lithium-sulfur (Li-S) batteries are considered promising candidates for advanced energy-storage systems. Despite tremendous efforts in suppressing the long-standing shuttle effect of lithium polysulfides, understanding of the interfacial reactions of lithium polysulfides at the nanoscale remains elusive. This is mainly because of the limitations of in situ characterization tools in tracing the liquid-solid conversion of unstable lithium polysulfides at high temporal-spatial resolution. There is an urgent need to understand the coupled phenomena inside Li-S batteries, specifically, the dynamic distribution, aggregation, deposition and dissolution of lithium polysulfides. Here, by using in situ liquid-cell electrochemical transmission electron microscopy, we directly visualized the transformation of lithium polysulfides over electrode surfaces at the atomic scale. Notably, an unexpected gathering-induced collective charge transfer of lithium polysulfides was captured on the nanocluster active-centre-immobilized surface. It further induced an instantaneous deposition of nonequilibrium Li2S nanocrystals from the dense liquid phase of lithium polysulfides. Without mediation of active centres, the reactions followed a classical single-molecule pathway, lithium polysulfides transforming into Li 2 S 2 and Li 2 S step by step. Molecular dynamics simulations indicated that the long-range electrostatic interaction between active centres and lithium polysulfides promoted the formation of a dense phase consisting of Li + and S n 2- (2 < n ≤ 6), and the collective charge transfer in the dense phase was further verified by ab initio molecular dynamics simulations. Finally, the collective interfacial reaction pathway unveils a new transformation mechanism and deepens the fundamental understanding of Li-S batteries.

25 ENERGY STORAGE↗

DOE OSTI2023

Observing ion diffusion and reciprocating hopping motion in water

When an ionic crystal dissolves in solvent, the positive and negative ions associated with solvent molecules release from the crystal. However, the existing form, interaction, and dynamics of ions in real solution are poorly understood because of the substantial experimental challenge. We observed the diffusion and aggregation of polyoxometalate (POM) ions in water by using liquid phase transmission electron microscopy. Real-time observation reveals an unexpected local reciprocating hopping motion of the ions in water, which may be caused by the short-range polymerized bridge of water molecules. We find that ion oligomers, existing as highly active clusters, undergo frequent splitting, aggregation, and rearrangement in dilute solution. The formation and dissociation of ion oligomers indicate a weak counterion-mediated interaction. Furthermore, POM ions with tetrahedral geometry show directional interaction compared with spherical ions, which presents structure-dependent dynamics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Stabilizing Liquids Using Interfacial Supramolecular Assemblies

Abstract Stabilizing liquids based on supramolecular assembly (non‐covalent intermolecular interactions) has attracted significant interest, due to the increasing demand for soft, liquid‐based devices where the shape of the liquid is far from the equilibrium spherical shape. The components comprising these interfacial assemblies must have sufficient binding energies to the interface to prevent their ejection from the interface when the assemblies are compressed. Here, we highlight recent advances in structuring liquids based on non‐covalent intermolecular interactions. We describe some of the progress made that reveals structure–property relationships. In addition to treating advances, we discuss some of the limitations and provide a perspective on future directions to inspire further studies on structured liquids based on supramolecular assembly.

Gu, Peiyang↗

DOE OSTI2023

Stabilizing Liquids Using Interfacial Supramolecular Assemblies

Stabilizing liquids based on supramolecular assembly (non-covalent intermolecular interactions) has attracted significant interest, due to the increasing demand for soft, liquid-based devices where the shape of the liquid is far from the equilibrium spherical shape. The components comprising these interfacial assemblies must have sufficient binding energies to the interface to prevent their ejection from the interface when the assemblies are compressed. In this report we highlight recent advances in structuring liquids based on non-covalent intermolecular interactions. We describe some of the progress made that reveals structure–property relationships. In addition to treating advances, we discuss some of the limitations and provide a perspective on future directions to inspire further studies on structured liquids based on supramolecular assembly.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗