Engineering Papers⌕ Search

Engineering topics

Zheng, Tianyue

Publications and source records attributed to Zheng, Tianyue.

At least 19 records

Investigation of SiO x anode fading mechanism with limited capacity cycling

Silicon suboxide (SiO x ) is one of the promising anode materials for the next-generation lithium-ion batteries. However, SiO x has a severe capacity fading problem during cycling. It is thus desired to investigate the detailed fading mechanisms of SiO x anode materials. In this study, limited capacity cycling was employed to examine the electrochemical behaviors of the SiO x anode, and the lithiation/delithiation cycling was limited within a range of 10% theoretical capacity. This strategy minimizes the volume variation of SiO x materials upon charging/discharging, which helps to reveal their decay factors other than volume fluctuation. It is demonstrated that the instability of the SiO x surface during cycling was likely a parallel factor of active material fading, which seems to cause unfavored electrode interface rearrangements with lowered electric conductivity.

electric vehicles↗

Conductive polymer emulsion

The present invention provides for an emulsion comprising solid particles of a single composition, or a mixture thereof, comprising a polymer comprising one monomer of an aryl methacrylate, or a mixture thereof, co-polymerized with a monomer of an alkyl methacrylate, or a mixture thereof; wherein Ar is an aryl group and R is an alkyl group, and n:m has a ratio of from about 0:100 to about 100:0.

Liu, Gao↗

Viscosity Analysis of Battery Electrode Slurry

We report the effects of component ratios and mixing time on electrode slurry viscosity. Three component quantities were varied: active material (graphite), conductive material (carbon black), and polymer binder (carboxymethyl cellulose, CMC). The slurries demonstrated shear-thinning behavior, and suspension properties stabilized after a relatively short mixing duration. However, micrographs of the slurries suggested their internal structures did not stabilize after the same mixing time. Increasing the content of polymer binder CMC caused the greatest viscosity increase compared to that of carbon black and graphite.

25 ENERGY STORAGE↗

Organic Solvent Free Process to Fabricate High Performance Silicon/Graphite Composite Anode

Cycling stability is a key challenge for application of silicon (Si)-based composite anodes as the severe volume fluctuation of Si readily leads to fast capacity fading. The binder is a crucial component of the composite electrodes. Although only occupying a small amount of the total composite mass, the binder has major impact on the long-term electrochemical performance of Si-based anodes. In recent years, water-based binders including styrene-butadiene rubber (SBR) and carboxymethyl cellulose (CMC) have attracted wide research interest as eco-friendly and low-cost alternatives for the conventional poly(vinylidene difluoride) (PVDF) binder in Si anodes. In this study, Si-based composite anodes are fabricated by simple solid mixing of the active materials with subsequent addition of SBR and CMC binders. This approach bypasses the use of toxic and expansive organic solvents. The factors of binder, silicon, and graphite materials have been systematically investigated. It is found that the retained capacities of the anodes are more than 440 mAh/g after 400 cycles. These results indicate that organic solvent free process is a facile strategy for producing high performance silicon/graphite composite anodes.

Fang, Chen (ORCID:0000000321011991)↗

Effects of Intra- and Interchain Interactions on Exciton Dynamics of PTB7 Revealed by Model Oligomers

Recent studies have shown that molecular aggregation structures in precursor solutions of organic photovoltaic (OPV) polymers have substantial influence on polymer film morphology, exciton and charge carrier transport dynamics, and hence, the resultant device performance. To distinguish photophysical impacts due to increasing π-conjugation from chain lengthening and π–π stacking from single/multi chain aggregation in solution and film, we used oligomers of a well-studied charge transfer polymer PTB7 with different lengths as models to reveal intrinsic photophysical properties of a conjugated segment in the absence of inter-segment aggregation. In comparison with previously studied photophysical properties in polymeric PTB7, we found that oligomer dynamics are dominated by a process of planarization of the conjugated backbone into a quinoidal structure that resembles the self-folded polymer and that, when its emission is isolated, this quinoidal excited state resembling the planar polymer chain exhibits substantial charge transfer character via solvent-dependent emission shifts. Furthermore, the oligomers distinctly lack the long-lived charge separated species characteristic of PTB7, suggesting that the progression from charge transfer character in isolated chains to exciton splitting in neat polymer solution is modulated by the interchain interactions enabled by self-folding.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Polaron and Exciton Delocalization in Oligomers of High-Performance Polymer PTB7

A key characteristic of organic photovoltaic cells is the efficient charge separation in the active layer. Sufficient delocalization of the positive polaron in organic photovoltaics is considered essential for the effective separation of the opposite charges and the suppression of recombination. Here we use light-induced EPR and ENDOR spectroscopy combined with DFT calculations to determine the electronic structure of the positive polaron in PTB7-type oligomers. Utilizing the superior spectral resolution of high-frequency (130 GHz) D-band EPR, the principal components of the g tensors were determined. Pulsed ENDOR spectroscopy at X-band allowed the measurement of H-1 hyperfine coupling constants. A comparison of g tensors and H-1 hyperfine coupling constants of the PTB7-type oligomers with the high-performance PTB7 polymer revealed a delocalization of the positive polaron in the polymer over about four monomeric units, corresponding to about 45 angstrom in length. Our current study thus not only determines the polaron delocalization length in PTB7 but also validates the approach combining EPR/ENDOR spectroscopy with DFT-calculated magnetic resonance parameters. This is of importance in those cases where oligomers of defined length are not easily obtained. In addition, the delocalization of the neutral triplet exciton was also determined in the oligomers and compared with polymer PTB7. The analysis revealed that the neutral triplet exciton is substantially more delocalized than the positive polaron, exceeding 10 monomeric units.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Highly Graphitized Carbon Coating on SiO with a π–π Stacking Precursor Polymer for High Performance Lithium-Ion Batteries

A highly graphitized carbon on a silicon monoxide (SiO) surface coating at low temperature, based on polymer precursor π–π stacking, was developed. A novel conductive and electrochemically stable carbon coating was rationally designed to modify the SiO anode materials by controlling the sintering of a conductive polymer, a pyrene-based homopolymer poly (1-pyrenemethyl methacrylate; PPy), which achieved high graphitization of the carbon layers at a low temperature and avoided silicon carbide formation and possible SiO material transformation. When evaluated as the anode of a lithium-ion battery (LIB), the carbon-coated SiO composite delivered a high discharge capacity of 2058.6 mAh/g at 0.05 C of the first formation cycle with an initial Coulombic efficiency (ICE) of 62.2%. After 50 cycles at 0.1 C, this electrode capacity was 1090.2 mAh/g (~82% capacity retention, relative to the capacity of the second cycle at 0.1 °C rate), and a specific capacity of 514.7 mAh/g was attained at 0.3 C after 500 cycles. Furthermore, the coin-type full cell composed of the carbon coated SiO composite anode and the Li[Ni0.5Co0.2Mn0.3O2] cathode attained excellent cycling performance. The results show the potential applications for using a π–π stacking polymer precursor to generate a highly graphitize coating for next-generation high-energy-density LIBs.

25 ENERGY STORAGE↗

Molecular Spring Enabled High-Performance Anode for Lithium Ion Batteries

Flexible butyl interconnection segments are synthetically incorporated into an electronically conductive poly(pyrene methacrylate) homopolymer and its copolymer. The insertion of butyl segment makes the pyrene polymer more flexible, and can better accommodate deformation. This new class of flexible and conductive polymers can be used as a polymer binder and adhesive to facilitate the electrochemical performance of a silicon/graphene composite anode material for lithium ion battery application. They act like a “spring” to maintain the electrode mechanical and electrical integrity. High mass loading and high areal capacity, which are critical design requirements of high energy batteries, have been achieved in the electrodes composed of the novel binders and silicon/graphene composite material. A remarkable area capacity of over 5 mAh/cm 2 and volumetric capacity of over 1700 Ah/L have been reached at a high current rate of 333 mA/g.

25 ENERGY STORAGE↗

Nucleophilic substitution between polysulfides and binders unexpectedly stabilizing lithium sulfur battery

Polysulfide shuttling has been the primary cause of failure in lithium-sulfur (Li-S) battery cycling. In this paper, we demonstrate an nucleophilic substitution reaction between polysulfides and binder functional groups can unexpectedly immobilizes the polysulfides. The substitution reaction is verified by UV–visible spectra and X-ray photoelectron spectra. The immobilization of polysulfide is in situ monitored by synchrotron based sulfur K-edge X-ray absorption spectra. The resulting electrodes exhibit initial capacity up to 20.4 mAh/cm 2 , corresponding to 1199.1 mAh/g based on a micron-sulfur mass loading of 17.0 mg/cm 2 . The micron size sulfur transformed into nano layer coating on the cathode binder during cycling. Directly usage of nano-size sulfur promotes higher capacity of 33.7 mAh/cm 2 , which is the highest areal capacity reported in Li-S battery. Finally, this enhance performance is due to the reduced shuttle effect by covalently binding of the polysulfide with the polymer binder.

25 ENERGY STORAGE↗

Investigating the Doping Mechanism of Pyrene Based Methacrylate Functional Conductive Binder in Silicon Anodes for Lithium-Ion Batteries

The doping mechanism of poly (1-pyrenemethyl methacrylate) (PPy) is investigated through electrochemical analytical and spectroscopic method. The performance of PPy as a Si materials binder is studied and compared with that of a commercial available lithium polyacrylate (PAALi) binder. The pyrene moiety consumes lithium ions according to the cyclic voltammogram (CV) measurement, as a doping to the PPy binder. Based on the lithium consumption, PPy based Si/graphite electrode doping is quantified at 1.1 electron/pyrene moiety. Lastly, the PPy binder based electrodes surface are uniform and crack free during lithiation/delithiation, which is revealed through Scanning electron microscope (SEM) imaging.

25 ENERGY STORAGE↗

Photophysical and morphological implications of single-strand conjugated polymer folding in solution

Organic semiconductors have garnered substantial interest in optoelectronics, but their device performances exhibit strong dependencies on material crystallinity and packing. In an effort to understand the interactions dictating the morphological and photophysical properties of a high-performing photovoltaic polymer, PTB7, a series of short oligomers and low molecular weight polymers of PTB7 were synthesized. Chain-length dependent optical studies of these oligomers demonstrate that PTB7’s low-energy visible absorption is largely due to self-aggregation-induced ordering, rather than in-chain charge transfer, as previously thought. By examining molecular weight and concentration dependent optical properties, supplemented by molecular dynamics simulations, we attribute polymeric PTB7’s unique midgap fluorescence and concentration independent absorption spectrum to an interplay between low molecular weight unaggregated strands and high-molecular weight self-aggregated (folded) strands. Specifically, we propose that the onset of PTB7 self-folding occurs between 7 and 13 repeat units, but the aggregates characteristic of polymeric PTB7 only develop at lengths of ~30 repeat units. Atomistic molecular dynamics simulations of PTB7 corroborate these conclusions, and a simple relation is proposed which quantifies the free-energy of conjugated polymer folding. Lastly, this study provides detailed guidance in the design of intra- and interchain contributions to the photophysical and morphological properties of polymeric semiconductors.

36 MATERIALS SCIENCE↗

Molecular Structure Controlled Transitions between Free-Charge Generation and Trap Formation in a Conjugated Copolymer Series

Charge transfer copolymers, where each repeating unit has at least one “donor” and one “acceptor” block, have played important roles in recent advances in organic photovoltaic (OPV) devices, however design criteria for these materials are still not completely clear. Here we show that the well-recognized LUMO-LUMO energy off-set design criterion for OPV materials using a fullerene acceptor is challenged in a series of copolymers, PTRn (n = 3, 5, 7 and 9), where n is the number of fused aromatic rings in the “donor” block and thienothiophene is the “acceptor” block in each repeating unit. Photoexcitation dynamics of PTRn copolymers in solution and BHJ (bulk heterojunction) films demonstrated that local push-pull interactions between the “donor” block and the “acceptor” block weakens with increasing n, whereas the LUMO-LUMO off-set between the polymer and PC71BM (Phenyl-C71-butyric acid methyl ester) increases. Such a counter intuitive trend can be explained by local energetics of each repeating unit as a function of n. The energetic changes transform the copolymer with strong local charge transfer character for efficient hole-electron separation to localized hole-electron pairs with low mobility, despite the apparent increase of the polymer/PC71BM LUMO-LUMO off-set. This suggests the importance of local charge transfer character in these copolymers in the initial exciton splitting dynamics, which could ultimately be reflected in the device performance.

36 MATERIALS SCIENCE↗

Electron Acceptors Based on α-Substituted Perylene Diimide (PDI) for Organic Solar Cells

The ortho-position functionalized perylene diimide derivatives (αPPID, αPBDT) were synthesized and used as the electron acceptors in nonfullerene organic photovoltaics. Due to the good planarity of ortho-position functionalized PDI, the αPPID and αPBDT show strong tendency to form aggregate because of their enhanced intermolecular pie-pie interaction. Moreover, they maintain the pure domains and the same packing order as in the pure film if they are blended with PBT7-TH and the SCLC measurement also shows the high electron mobility. The inverted OPVs employing αPDI-based compounds as acceptor and PBT7-TH as the donor give the highest PCE of 4.92 % for αPBDT based device and 3.61 % for αPPID based device, which is 39 % and 4 % higher than that for their counterpart βPBDT and βPPID. The charge separation study shows the more efficient exciton dissociation at interfaces between PDI based compounds and PBT7-TH. In conclusion, the results suggest that compared to beta-substituted ones, alpha-substituted PDI derivatives are more promising electron acceptors for OPV.

14 SOLAR ENERGY↗

Wide bandgap OPV polymers based on pyridinonedithiophene unit with efficiency >5%

We report the properties of a new series of wide band gap photovoltaic polymers based on the N -alkyl 2-pyridone dithiophene (PDT) unit. These polymers are effective bulk heterojunction solar cell materials when blended with phenyl-C 71 -butyric acid methyl ester (PC 71 BM). They achieve power conversion efficiencies (up to 5.33%) high for polymers having such large bandgaps, ca. 2.0 eV (optical) and 2.5 eV (electrochemical). As a result, grazing incidence wide-angle X-ray scattering (GIWAXS) reveals strong correlations between π–π stacking distance and regularity, polymer backbone planarity, optical absorption maximum energy, and photovoltaic efficiency.

14 SOLAR ENERGY↗

Optical, Electrical, and Magnetic Studies of Organic Solar Cells Based on Low Bandgap Copolymer with Spin ½ Radical Additives

The charge photogeneration and recombination processes in organic photovoltaic solar cells based on blend of the low bandgap copolymer, PTB7 (fluorinated poly‐thienothiophene‐benzodithiophene) with C60‐PCBM using optical, electrical, and magnetic measurements in thin films and devices is studied. A variety of steady state optical and magneto‐optical techniques were employed, such as photoinduced absorption (PA), magneto‐PA, doping‐induced absorption, and PA‐detected magnetic resonance (PADMR); as well as picosecond time‐resolved PA. The charge polarons and triplet exciton dynamics in films of pristine PTB7, PTB7/fullerene donor–acceptor (D–A) blend is followed. It is found that a major loss mechanism that limits the power conversion efficiency (PCE) of PTB7‐based solar cell devices is the “back reaction” that leads to triplet exciton formation in the polymer donor from the photogenerated charge‐transfer excitons at the D–A interfaces. A method of suppressing this “back reaction” by adding spin½ radicals Galvinoxyl to the D–A blend is presented; this enhances the cell PCE by ≈30%. The same method is not effective for cells based on PTB7/C70‐PCBM blend, where high PCE is reached even without Galvinoxyl radical additives.

Basel, Tek↗