Engineering Papers⌕ Search

Engineering topics

Zhao, Yuji (ORCID:0000000191994159)

Publications and source records attributed to Zhao, Yuji (ORCID:0000000191994159).

12 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Reduced trap state density in AlGaN/GaN HEMTs with low-temperature CVD-grown BN gate dielectric

In this Letter, low-temperature (400 °C) chemical vapor deposition-grown boron nitride (BN) was investigated as the gate dielectric for AlGaN/GaN metal–insulator–semiconductor high electron mobility transistors (MISHEMTs) on a Si substrate. Comprehensive characterizations using x-ray photoelectron spectroscopy, reflection electron energy loss spectroscopy, atomic force microscope, high-resolution transmission electron microscopy, and time-of-flight secondary ion mass spectrometry were conducted to analyze the deposited BN dielectric. Compared with conventional Schottky-gate HEMTs, the MISHEMTs exhibited significantly enhanced performance with 3 orders of magnitude lower reverse gate leakage current, a lower off-state current of 1 × 10−7 mA/mm, a higher on/off current ratio of 108, and lower on-resistance of 5.40 Ω mm. The frequency-dependent conductance measurement was performed to analyze the BN/HEMT interface, unveiling a low interface trap state density (Dit) on the order of 5 × 1011–6 × 1011 cm−2 eV−1. This work shows the effectiveness of low-temperature BN dielectrics and their potential for advancing GaN MISHEMTs toward high-performance power and RF electronics applications.

Physics↗
DOE OSTI2024

High temperature stability of regrown and alloyed Ohmic contacts to AlGaN/GaN heterostructure up to 500 °C

This Letter reports the stability of regrown and alloyed Ohmic contacts to AlGaN/GaN-on-Si high electron mobility transistors (HEMTs) for high temperature applications up to 500 °C. Transfer length method (TLM) measurements from 25 to 500 °C in air show that the regrown contacts appear to be stable up to 500 °C during short term (approximately 1 h) testing, while alloyed contacts appear to decrease in contact resistance from 300 to 500 °C though increases in the error bounds due to increase sheet resistance make it difficult to conclude definitely. Additionally, longer term testing shows both technologies remain stable at least up to 48 h at 500 °C, after which the large increase in sheet resistance makes the measurement uncertainty too large to conclude definitively. Advanced microscopy images indicate both the regrown and alloyed contact regions remain structurally intact after prolonged high temperature exposure with no visible degradation in crystallinity or metal composition.

Physics↗
DOE OSTI2024

Modulation of dielectric properties of hexagonal/cubic boron nitride composites

In this work, we synthesized mixed-phase hexagonal-boron nitride (h-BN)/cubic-BN (c-BN) composites with varying ratios and investigated their frequency and temperature-dependent dielectric properties. As the ratio of c-BN increased, we observed a corresponding increase in the dielectric constant of the composites. Furthermore, we used spark-plasma sintering (SPS) to treat the mixed-phase composite, which resulted in a phase transformation from mixed phase to pure h-BN phase. Remarkably, the composite exhibited an increase in dielectric constant after the SPS process, which can be attributed to the densification of the composite and the enhancement in grain size. Our approach presents a promising strategy for effectively modulating the dielectric properties of BN, which is crucial for advanced electronics.

Physics↗
DOE OSTI2024

Device and material investigations of GaN enhancement-mode transistors for Venus and harsh environments

This Letter reports the device and material investigations of enhancement-mode p-GaN-gate AlGaN/GaN high electron mobility transistors (HEMTs) for Venus exploration and other harsh environment applications. The GaN transistor in this work was subjected to prolonged exposure (11 days) in a simulated Venus environment (460 °C, 94 bar, complete chemical environment including CO2/N2/SO2). The mechanisms affecting the transistor performance and structural integrity in harsh environment were analyzed using a variety of experimental, simulation, and modeling techniques, including in situ electrical measurement (e.g., burn-in) and advanced microscopy (e.g., structural deformation). Through transistor, Transmission Line Method (TLM), and Hall-effect measurements vs temperature, it is revealed that the mobility decrease is the primary cause of reduction of on-state performance of this GaN transistor at high temperature. Material analysis of the device under test (DUT) confirmed the absence of foreign elements from the Venus atmosphere. No inter-diffusion of the elements (including the gate metal) was observed. The insights of this work are broadly applicable to the future design, fabrication, and deployment of robust III-N devices for harsh environment operation.

Physics↗
DOE OSTI2023

Vertical β -Ga2O3 metal–insulator–semiconductor diodes with an ultrathin boron nitride interlayer

In this work, we demonstrate the high performance of β-Ga2O3 metal–insulator–semiconductor (MIS) diodes. An ultrathin boron nitride (BN) interlayer is directly grown on the Ga2O3 substrate by pulsed laser deposition. X-ray photoelectron spectroscopy, Raman spectroscopy, and high-resolution transmission electron microscopy confirm the existence of a 2.8 nm BN interlayer. Remarkably, with the insertion of the ultrathin BN layer, the breakdown voltage is improved from 732 V for Ga2O3 Schottky barrier diodes to 1035 V for Ga2O3 MIS diodes owing to the passivated surface-related defects and reduced reverse leakage currents. Our approach shows a promising way to improve the breakdown performance of Ga2O3-based devices for next-generation high-power electronics.

Physics↗
DOE OSTI2023

Low-frequency noise in β-(Al x Ga1 −x )2O3 Schottky barrier diodes

We report on the low-frequency electronic noise in β-(AlxGa1−x)2O3 Schottky barrier diodes. The noise spectral density reveals 1/f dependence, characteristic of the flicker noise, with superimposed Lorentzian bulges at the intermediate current levels (f is the frequency). The normalized noise spectral density in such diodes was determined to be on the order of 10−12 cm2/Hz (f = 10 Hz) at 1 A/cm2 current density. At the intermediate current regime, we observed the random telegraph signal noise, correlated with the appearance of Lorentzian bulges in the noise spectrum. The random telegraph signal noise was attributed to the defects near the Schottky barrier. The defects can affect the local electric field and the potential barrier and, correspondingly, impact the electric current. The obtained results help in understanding the noise in Schottky barrier diodes made of ultra-wide bandgap semiconductors and can be used for the material and device quality assessment.

Physics↗
DOE OSTI2022

GaN-on-GaN p-i-n diodes with avalanche capability enabled by eliminating surface leakage with hydrogen plasma treatment

Traditional mesa terminations require precise angle design to reduce the electric field at the edge and surface treatment to reduce etch damage. Otherwise, the device usually suffers a premature breakdown. This work proposes the use of easy-to-implement hydrogen plasma treatment to solve the premature breakdown caused by mesa and demonstrates the avalanche capability in GaN-on-GaN p-i-n diodes. The breakdown electric field when the avalanche occurred was ∼2.3 MV/cm at room temperature for a GaN drift layer with a doping concentration of ∼7 × 1015 cm−3, which is consistent with the theoretical value. The temperature coefficient of the avalanche breakdown voltage of the devices was 4.64–4.85 × 10−4 K−1. This work shows a simple and effective approach to achieve avalanche capability in vertical GaN power devices, which can serve as an important reference for the future development of efficient and robust GaN power electronics.

Fu, Kai (ORCID:0000000294057512)↗
DOE OSTI2022

External charge compensation in etched gallium nitride measured by x-ray photoelectron spectroscopy

Electronic states at GaN surfaces and at regrowth and heteroepitaxy interfaces inhibit electronic device performance. Understanding electronic state configuration at the GaN surface is, therefore, crucial for the development of GaN-based devices, which are currently of considerable interest in power electronic applications. GaN and other wurtzite III-nitrides possess large spontaneous polarization along the c-axis, producing a bound sheet charge at the surface, which affects the electronic state configuration through the formation of internal and external compensation charges. Defects induced by conventional plasma-based dry etching methods may inhibit the internal screening of this bound charge and thus increase the concentration of external charged states. The surface band bending of n-type Ga-face GaN (0001) was measured with x-ray photoelectron spectroscopy after inductively coupled plasma etching to investigate the impact of dry etching on external charge compensation. GaN samples were etched using inductively coupled plasma with varying rf power and a novel plasma-enhanced atomic layer etching method using an oxidation, fluorination, and ligand-exchange mechanism. The band bending varied from 0.0 to 0.8 ± 0.1 eV for the samples measured.

Hatch, Kevin A. (ORCID:0000000283118623)↗
DOE OSTI2020

Structural breakdown in high power GaN-on-GaN p-n diode devices stressed to failure

The morphology of GaN-on-GaN vertical p-i-n diode devices after reverse-bias electrical stressing to breakdown has been investigated. All failed devices had irreversible structural damage, showing large surface craters that were ∼15–35 μm deep with lengthy surface cracks. Cross-sectional electron micrographs of failed devices showed substantial concentrations of threading dislocations around the cracks and near the crater surfaces. Progressive ion-milling across damaged devices revealed high densities of threading dislocations and the presence of voids beneath the surface cracks; these features were not observed in any unstressed devices. These results should serve as a useful reference for future reliability studies of vertical high-power GaN devices.

Peri, Prudhvi (ORCID:000000022338441X)↗
DOE OSTI2020

Demonstration of GaN-based metal–insulator–semiconductor junction by hydrogen plasma treatment

We demonstrate a nickel/insulating-GaN (i-GaN)/p-type GaN junction and investigate its electrical properties. The i-GaN is formed by exposure to a low-power hydrogen plasma to passivate the p-GaN layer. Cathodoluminescence spectroscopy of the i-GaN is used to understand the passivation effect of the hydrogen plasma on p-GaN. The junction shows very low leakage (<10−9 A at −50 V), excellent rectifying properties (∼107), high temperature stability, and blue light electroluminescence at forward bias. A bandgap model is proposed to illustrate the electrical properties of hydrogenated p-GaN and to understand the device characteristics.

Yang, Chen (ORCID:0000000230090882)↗