Engineering Papers⌕ Search

Engineering topics

Zhang, X.

Publications and source records attributed to Zhang, X..

At least 73 records · Page 4

Design of super-strong and thermally stable nanotwinned Al alloys via solute synergy

Al alloys have widespread industrial applications. However, their mechanical strength is often much lower than steels. Here, we investigate the influence of solutes on achieving ultrahigh strength and thermal stability of nanotwinned Al alloys. In situ micropillar compression tests show the addition of a small amount of Ti can significantly increase the mechanical strength of Al–Ni alloys to 2 GPa. Deformation induced detwinning, Ni segregation and grain coarsening as discovered in binary Al–Ni alloys are mostly absent in the ternary Al–Ni–Ti alloys. Moreover, the ternary Al–Ni–Ti alloys have outstanding thermal stability. Density function theory calculations reveal the synergetic pinning effect of Ni–Ti solute pairs on incoherent twin boundaries. This study demonstrates that the proper selection of synergistic solute pairs is critical to improve the thermal stability and mechanical properties of nanotwinned Al alloys.

36 MATERIALS SCIENCE↗

Radiation hardness of the low gain avalanche diodes developed by NDL and IHEP in China

This paper presents a study on the radiation hardness of low gain avalanche detector (LGAD) developed by the Novel Device Laboratory (NDL) in Beijing and the Institute of High Energy Physics (IHEP) of Chinese Academy of Sciences, in the context of an upgrade project of the ATLAS detector for the high luminosity phase of LHC. NDL LGAD sensors with different layouts, epitaxial resistivity and doping profile were irradiated up to 1.02 × 10 15 n eq /cm 2 by 70 MeV protons at Cyclotron and Radioisotope Center (CYRIC). The timing resolution of NDL LGAD sensors reached 50 ps and the collected charge reached 3 - 4 fC after irradiation.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

MMSS Indepent Review Questions and Answers

Program managers' questions and researchers' answers are provided, documenting this review. The technical aims of the project being reviewed were to establish additively manufactured (AM) scintillator metamaterial designs that can perform in nonproliferation applications, to quantify that performance using simulations, and to justify that simulated performance using prototyping.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

FY20 Status Report on Creep Rupture Testing to Support the Development of Alloy 709 Code Case

This report provides an update on the status of the creep rupture testing on the first commercial heat of Alloy 709 in support of the Alloy 709 Code Case development. A creep test laboratory has been set up at ANL that comprises of 15 indirectly loaded test frames capable of testing ASTM-size specimens of the commercial heat of Alloy 709. The systems are equipped with high temperature furnaces capable of operation up to 1000°C in an air environment. During FY18, uniaxial ASTM-sized creep specimens were fabricated from 9 Alloy 709 plates that were processed by AOD, ESR, and ESR-homogenized routes and subsequently solution annealed at 1050, 1100, and 1150°C, and creep-rupture tests were performed at 330MPa and 600°C. The test results led to the down selection of the ESR-1100°C condition to support the code case. In FY19, 15 creep-rupture tests of the ESR-1100°C material, requiring the use of Type K thermocouples, were initiated to support the 100,000-hour Code Case. 8 tests were completed in FY19. In FY20, 6 tests were completed at the time of writing this report. In addition, 1 more test were loaded in FY20, using Type S thermocouples, and was completed. This report presents the data from the completed tests in FY20 and also the microstructural characterization of the fractured specimens. The creep data enabled the preliminary analysis of the creep behavior of this material. The characterization showed that in brittle fractures, the pores were narrow and thin, and elongated in the direction perpendicular to the loading direction, while in ductile fractures, the pores were much rounder. Dense precipitates were observed in all the samples, the size of which grew with test temperature. Some of the precipitates could be identified to be M23C6 based on their cuboid shape.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Report on the FY20 Characterization of Age Hardened Alloy 709 Materials

This report provides the results on microstructural characterization of the first commercial heat of Alloy 709 plate material undergone additional age hardening treatment. In FY19, through thermodynamic-kinetic modeling and microstructural characterization, it is determined that the 775°C/10 h age-hardening treatment can promote desired precipitation on dislocations and has the potential to further improve the mechanical performance of the material. In FY20, the treatment protocol was applied to the ESR-1150°C condition, and the microstructure was then compared with the ESR-1100°C condition. It was found that the 1150°C solution annealing (SA) dramatically reduced the dislocation density compared to the 1100°C SA, resulting a smaller number density of Nb-rich fine precipitates which grow on dislocations during the age hardening treatment. Other features are very similar between the two. The effect of age hardening on creep performance is discussed. In addition, TEM characterization of a creep-ruptured sample (600°C/330 MPa) was performed. Specimens from the grip region and the gauge region was studied. The grip region specimen was effectively aged at 600°C for extended period, while the gauge region specimen was mechanically deformed at 600°C. The microstructures are very different, implying the importance of a dynamical effect on precipitation.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Radiation campaign of HPK prototype LGAD sensors for the High-Granularity Timing Detector (HGTD)

In this work, we report on the results of a radiation campaign with neutrons and protons of Low Gain Avalanche Detectors (LGAD) produced by Hamamatsu (HPK) as prototypes for the High-Granularity Timing Detector (HGTD) in ATLAS. Sensors with an active thickness of were irradiated in steps of roughly 2 up to a fluence of 3. As a function of the fluence, the collected charge and time resolution of the irradiated sensors will be reported for operation at °C.

47 OTHER INSTRUMENTATION↗

Deformation behavior and phase transformation of nanotwinned Al/Ti multilayers

We report nanotwinned Al/Ti multilayers have exhibited size-dependent microstructure evolution and high strength. However, their deformation mechanisms are less well understood. In this work, we investigated the deformation mechanisms of nanotwinned Al/Ti multilayers with FCC/HCP layer interfaces by using in situ micropillar compression tests. Nanotwinned Al/Ti multilayers exhibit compressive strength up to 2.4 GPa and good work hardening capability. Post-compression TEM analyses reveal high-density stacking faults and the HCP-to-FCC phase transformations in Ti. Molecular dynamics simulations elucidate the mechanisms of deformation induced phase transformation in Ti and the influence of collective movement of partial dislocations on the deformability of Al/Ti multilayers.

36 MATERIALS SCIENCE↗

Nonfuel antineutrino contributions in the ORNL High Flux Isotope Reactor (HFIR)

Reactor neutrino experiments have seen major improvements in precision in recent years. With the experimental uncertainties becoming lower than those from theory, carefully considering all sources of $\bar{ν}$ e is important when making theoretical predictions. One source of νe that is often neglected arises from the irradiation of the nonfuel materials in reactors. The $\bar{ν}$ e rates and energies from these sources vary widely based on the reactor type, configuration, and sampling stage during the reactor cycle and have to be carefully considered for each experiment independently. In this article, we present a formalism for selecting the possible $\bar{ν}$ e sources arising from the neutron captures on reactor and target materials. We apply this formalism to the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory, the $\bar{ν}$ e source for the the Precision Reactor Oscillation and Spectrum Measurement (PROSPECT) experiment. Overall, we observe that the nonfuel $\bar{ν}$ e contributions from HFIR to PROSPECT amount to 1% above the inverse beta decay threshold with a maximum contribution of 9% in the 1.8–2.0 MeV range. Nonfuel contributions can be particularly high for research reactors like HFIR because of the choice of structural and reflector material in addition to the intentional irradiation of target material for isotope production. We show that typical commercial pressurized water reactors fueled with low-enriched uranium will have significantly smaller nonfuel $\bar{ν}$ e contribution.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

The radioactive source calibration system of the PROSPECT reactor antineutrino detector

The Precision Reactor Oscillation and Spectrum (PROSPECT) Experiment is a reactor neutrino experiment created to search for sterile neutrinos with a mass on the order of 1 eV/c 2 and to measure the spectrum of electron antineutrinos from a highly-enriched 235 U nuclear reactor. The PROSPECT detector consists of an 11 by 14 array of optical segments in 6 Li-loaded liquid scintillator at the High Flux Isotope Reactor in Oak Ridge National Laboratory. Antineutrino events are identified via inverse beta decay and read out by photomultiplier tubes located at the ends of each segment. The detector response is characterized using a radioactive source calibration system. Here, we describe the design, operation, and performance of the PROSPECT source calibration system.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Impact Behavior of Polyetheretherketone/Nickel Foam Co-continuous Composites

In this study, we prepared eight types of polyetheretherketone/nickel (PEEK/Ni) foam co-continuous phase composites (named “PEEK-Nis”) in which virgin PEEK was infiltrated into homologous hollow Ni structures by using hot pressing. Their Charpy impact behavior was investigated in accordance with ISO: 179-1, and the effect of the structure of the foam Ni on the impact properties of the PEEK-Nis was also studied. Compared with unfilled PEEK, the Ni prisms can effectively disperse, transfer, and absorb the energy of the pendulum, further improve the impact toughness of the PEEK-Nis and eventually lead to different fracture modes. The impact toughness of PEEK-Nis was mainly affected by Ni volume fraction, coating thickness, and pores per inch (PPI) value, which are mutually restricted. When the Ni content was less than 8.5%, the impact toughness of PEEK-Nis increased with an increase in PPI value. When the Ni content was between 8.5 and 18%, the impact toughness of PEEK-Nis increased with the coating thickness. When the Ni content exceeded 18%, the impact toughness decreased dramatically possibly because of the mechanical mismatch of the two-phase materials in PEEK-Nis. For further optimization, PEEK-NiB-2 was fabricated and had the most reasonable structure of the reinforcing phase. Among all PEEK-Nis, PEEK-NiB-2 exhibited the best impact toughness, with a value over two times that of unfilled PEEK.

36 MATERIALS SCIENCE↗

FY19 Status Report on Creep Test Data on Commercial Heat of Alloy 790

This report provides an update on the status of the creep rupture testing on the first commercial heat of Alloy 709 in support of the Alloy 709 Code Case development. The report is a Level 3 deliverable in FY19 (M3AT-19AN020502041), under the Work Package AT19AN0205204, “A709 Code Case Testing” performed by Argonne National Laboratory (ANL), as part of the Advanced Reactor Technologies Program. A creep test laboratory has been set up at ANL that comprises of 15 indirectly loaded test frames capable of testing ASTM standard-size specimens of the commercial heat of Alloy 709. The systems are equipped with high temperature furnaces capable of operation up to 1000°C in an air environment. In FY19, 15 creep-rupture tests of the ESR-1100°C solution annealed material, requiring the use of Type K thermocouples, were initiated to support the 100,000-hour Code Case. At the time of writing this report, eight tests were completed. This report presents the data from those completed tests and also microstructural characterization of the fractured specimens. During FY19, efforts were being made to add Type S thermocouples to five of the creep test frames, for performing longer term tests at higher temperatures.

36 MATERIALS SCIENCE↗

Microstructural Characterization of Alloy 709 Plate Materials with Additional Heat Treatment Protocol

This report provides the results on microstructural characterization of the first commercial heat of Alloy 709 plate material which has undergone additional heat treatment protocol. The report is a Level 4 deliverable in FY19 (M4AT-19AN020502012), under the Work Package AT19AN0205201, “A709 Development – ANL.” The study involves thermodynamic-kinetic modeling, heat treating of materials, microhardness testing, x-ray diffraction (XRD) study, scanning electron microscopy (SEM), and transmission electron microscopy (TEM) study. Through thermodynamic-kinetic modeling, it is determined that after an 1100°C solutionizing treatment, heat treating of Alloy 709 at 775°C for 10 hours or at 900°C for 10 hours are candidate recipes for promoting desired microstructural features. Both heat treatments were executed on small samples of the AOD-1100°C condition of the commercial heat of Alloy 709. Micro-hardness tests showed that both treatments increases the hardness of the material. XRD showed that both treatments brings out M23C6 and MX phases, though the 775°C/10h-treatment has more profound effect. The TEM study revealed that similar for both conditions, M23C6 precipitated on grain boundaries and within grain interior. In contrast, after the 775°C/10h treatment, the dislocations are decorated with MX nano particles, while after the 900°C/10h treatment, most of the dislocations are free of MX particles. It is thus determined that the 775°C/10h treatment has a better potential to provide enhanced creep properties by pinning the dislocations with nano particles. Following this study, the 775°C/10h treatment was carried out on a large ESR-1100°C plate at Idaho National Laboratory. Hardness testing and microstructural characterization were performed and compared between the two materials being heated treated under the same protocol. The implication on mechanical properties was briefly discussed.

36 MATERIALS SCIENCE↗

Measurement of the Antineutrino Spectrum from U 235 Fission at HFIR with PROSPECT

This Letter reports the first measurement of the 235 U ν¯ e energy spectrum by PROSPECT, the Precision Reactor Oscillation and Spectrum experiment, operating 7.9m from the 85MW th highly-enriched uranium (HEU) High Flux Isotope Reactor. With a surface-based, segmented detector, PROSPECT has observed 31678 ± 304 (stat.) ν¯ e -induced inverse beta decays (IBD), the largest sample from HEU fission to date, 99% of which are attributed to 235 U. Despite broad agreement, comparison of the Huber 235 U model to the measured spectrum produces a χ 2 /ndf = 51.4/31, driven primarily by deviations in two localized energy regions. As a result, the measured 235 U spectrum shape is consistent with a deviation relative to prediction equal in size to that observed at low-enriched uranium power reactors in the ν¯ e energy region of 5-7MeV.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

The Evolution of a Pitch-Angle "Bite-Out" Scattering Signature Caused by EMIC Wave Activity: A Case Study

Electromagnetic ion cyclotron (EMIC) waves are understood to be one of the dominant drivers of relativistic electron loss from Earth's radiation belts. Theory predicts that the associated gyroresonant wave‐particle interaction results in a distinct energy‐dependent “bite‐out” signature in the normalized flux distribution of electrons as they are scattered into the loss cone. We identify such signatures along with the responsible EMIC waves captured in situ by the Van Allen Probes on 15–16 February 2017. Using the cold plasma approximation, we predict the pitch‐angle cutoffs for the scattering signature for the captured EMIC wave and find it in good agreement with the observed electron bite‐out scattering signature. Employing the close conjunction between the Van Allen Probes and THEMIS during this time, we explore the temporal and spatial evolution of the scattering signature, as well as the surrounding wave activity, and find that the scattering signature formed during continued wave activity over a period less than a day. These results are consistent with wave‐particle interaction theory and support the hypothesis that EMIC waves are an important mechanism for rapid relativistic electron loss from the radiation belts.

Bingley, L.↗