Engineering Papers⌕ Search

Engineering topics

Zhang, Li

Publications and source records attributed to Zhang, Li.

At least 73 records · Page 4

The ETROC Project: Precision Timing ASIC Development for LGAD-based CMS Endcap Timing Layer (ETL) Upgrade

The ETROC (Endcap Timing Readout Chip) is being developed for the LGAD-based CMS Endcap Timing Layer (ETL) at HL-LHC. The ETL on each side of the interaction region will be instrumented with a two-disk system of MIP-sensitive LGAD silicon devices to be read out by ETROCs for precision timing measurement with down to 30 ps timing resolution. The ETROC is designed to handle a 16 x 16 pixel cell matrix, with each pixel cell being 1.3 mm x 1.3 mm to match the LGAD sensor pixel size. Approximately 15% of the sensors near the highest eta region will experience hadron fluence above 1e15 neq/cm² towards end of operation of HL-LHC, resulting in small signal amplitude with LGAD gain reduced to around 10. For this reason, the front-end design for preamplifier and discriminator has been specifically optimized for the reduced LGAD signals, with enough flexibilities to meet the ETL specific needs for time resolution, power budget and radiation profile.

97 MATHEMATICS AND COMPUTING↗

Stability of Fe-bearing hydrous phases and element partitioning in the system MgO–Al 2 O 3 –Fe 2 O 3 –SiO 2 –H 2 O in Earth’s lowermost mantle

We performed high pressure–temperature ( P-T ) experiments on a model composition of hydrous subducted slabs in the MgO–Al 2 O 3 –Fe 2 O 3 –SiO 2 –H 2 O system using laser-heated diamond anvil cells. The phase assemblages were characterized combining in-situ synchrotron X-ray diffraction and ex-situ transmission electron microscope techniques. The hydrous δ-phase AlOOH–FeOOH–MgSiO 2 (OH) 2 –SiO 2 coexists with bridgmanite (Bdg), post-perovskite (pPv), or both in a broad P-T range of 104–126 GPa and 1750–2500 K. The hydrous pyrite-type FeOOHx phase was observed in-situ over a P-T range of 112–123 GPa and 1750–2300 K, coexisting with the pPv phase. Chemical analysis on recovered samples showed that considerable amount of Fe 2 O 2 (OH) 2 (8–13 mol%) and SiO 2 (9–13 mol%) in the δ-phase does not reduce its thermal stability compared to the Al-endmember, indicating that the Fe-bearing δ-phase can transport water to the lowermost mantle along the mantle geotherm. In this hydrous system, we observed that Al depletion in both the Bdg and pPv phases can significantly reduce the width of the Bdg to pPv transition in contrast to a wide two-phase coexistence region in a dry Al-rich system. Meanwhile, the Fe enrichment in the pPv phase relative to the coexisting Bdg phase lowers the transition pressure to the depth of the D" discontinuity. Accordingly, the depth and thickness of the Bdg to pPv transition in subducted basaltic crustal materials can explain the seismically detected D" discontinuity. Partial melting could be triggered by dehydration of the Fe-bearing hydrous phases due to a steep temperature gradient at the core mantle boundary (CMB), and therefore the ultralow-velocity zones (ULVZs) might be the regions where partial melting occurs at the lowermost mantle.

58 GEOSCIENCES↗

Silver Nanoparticles Induced Cell Apoptosis, Membrane Damage of Azotobacter vinelandii and Nitrosomonas europaea via Generation of Reactive Oxygen Species

Silver nanoparticles (AgNPs) is widely used as an antibacterial agent, but the specific antibacterial mechanism is still conflicting. This study aimed to investigate the size dependent inhibition of AgNPs and the relationship between inhibition and reactive oxygen species (ROS). Azotobactervinelandii and Nitrosomonaseuropaea were exposed to AgNPs with different particles size (10 nm and 50 nm). The ROS production was measured and the results showed that the generation of ROS related to the particle size and concentrations of AgNPs. At 10 mg/L of 10 nm Ag particles, the apoptosis rate of A. vinelandii and N. europaea were 20.23% and 1.87% respectively. Additionally, the necrosis rate of A. vinelandii and N. europaea reached to 15.20% and 42.20% respectively. Furthermore, transmission electron microscopy images also indicated that AgNPs caused severely bacterial cell membrane damage. Together these data suggested that the toxicity of AgNPs depends on its particle size and overproduction of ROS.

54 ENVIRONMENTAL SCIENCES↗

Crystal Structure of the Ergothioneine Sulfoxide Synthase from Candidatus Chloracidobacterium thermophilum and Structure-Guided Engineering To Modulate Its Substrate Selectivity

Ergothioneine is a thiohistidine derivative with potential benefits on many aging-related diseases. The central step of aerobic ergothioneine biosynthesis is the oxidative C–S bond formation reaction catalyzed by mononuclear nonheme iron sulfoxide synthases (EgtB and Egt1). Thus far, only the Mycobacterium thermoresistibile EgtB (EgtB Mth ) crystal structure is available, while the structural information for the more industrially attractive Egt1 enzyme is not. In this paper, we reported the crystal structure of the ergothioneine sulfoxide synthase (EgtB Cth ) from Candidatus Chloracidobacterium thermophilum . EgtB Cth has both EgtB- and Egt1-type of activities. Guided by the structural information, we conducted Rosetta Enzyme Design calculations, and we biochemically demonstrated that EgtB Cth can be engineered more toward Egt1-type of activity. This study provides information regarding the factors governing the substrate selectivity in Egt1- and EgtB-catalysis and lays the groundwork for future sulfoxide synthase engineering toward the development of an effective ergothioneine process through a synthetic biology approach.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

QTL × environment interactions underlie adaptive divergence in switchgrass across a large latitudinal gradient

Local adaptation is the process by which natural selection drives adaptive phenotypic divergence across environmental gradients. Theory suggests that local adaptation results from genetic trade-offs at individual genetic loci, where adaptation to one set of environmental conditions results in a cost to fitness in alternative environments. However, the degree to which there are costs associated with local adaptation is poorly understood because most of these experiments rely on two-site reciprocal transplant experiments. Here, we quantify the benefits and costs of locally adaptive loci across 17° of latitude in a four-grandparent outbred mapping population in outcrossing switchgrass ( Panicum virgatum L.), an emerging biofuel crop and dominant tallgrass species. We conducted quantitative trait locus (QTL) mapping across 10 sites, ranging from Texas to South Dakota. This analysis revealed that beneficial biomass (fitness) QTL generally incur minimal costs when transplanted to other field sites distributed over a large climatic gradient over the 2 y of our study. Therefore, locally advantageous alleles could potentially be combined across multiple loci through breeding to create high-yielding regionally adapted cultivars.

59 BASIC BIOLOGICAL SCIENCES↗

Active and stable Pt-Ceria nanowires@silica shell catalyst: Design, formation mechanism and total oxidation of CO and toluene

Cerium oxide is one of the most important rare earth metal oxides in catalysis, however, the sintering problem of noble metals and CeO 2 at higher temperature (e.g., >700 °C) is still unresolved. Herein, Pt nanoparticles self-assembled on ultra-thin CeO 2 nanowires (NWs) and then confined inside a thermally robust porous silica shell (Pt-CeO2NW@SiO 2 ) were introduced. The thickness of CeO 2 NWs was just ~2.0 nm. Moreover, Pt-CeO 2 NW@SiO 2 showed significantly enhanced catalytic performances for total oxidation of CO and toluene. The increased catalytic properties are attributed to the strong metal-support interaction effect between Pt and CeO 2 NWs at sub-nanoscale. Most importantly, the special core-shell structure also affords excellent sintering resistance retention up to 700 °C for 100 h, due to the guarding effect of porous silica shell. Finally, the formation mechanism of Pt-CeO 2 NW@SiO 2 was investigated in detail. Current strategy should inspire many rational designs of rare-earth metal-based nanocatalysts for real-world catalysts.

36 MATERIALS SCIENCE↗

The Impact of Radiotherapy on Reoperation Rates in Patients Undergoing Mastectomy and Breast Reconstruction

Objective: The aim of this study was to determine the impact of postmastectomy radiotherapy (PMRT) on reoperation rates in women with breast cancer undergoing mastectomy and breast reconstruction. Methods: Between June 2001 and December 2015, 832 breast cancer patients treated with mastectomy and breast reconstruction with (n = 159) or without (n = 673) PMRT were analyzed retrospectively. Reoperations following breast reconstruction were categorized into the following three types: anticipated, unanticipated, and others. Multivariable logistic regression models were used to evaluate the impact of PMRT on overall and unanticipated reoperations according to different breast reconstruction types after adjusting for relevant covariates. Results: With a median follow-up of 58.5 months, a total of 1298 operations were performed in 832 breast cancer patients. The rates of overall and unanticipated reoperations were 46.2% and 7.7%, respectively. Multivariable analysis showed that PMRT was not associated with overall reoperations in either implant-based reconstruction patients (odds ratio [OR] 1.00, 95% confidence interval [CI] 0.43–2.37, p = 0.995) or autologous reconstruction patients (OR 0.85, 95% CI 0.52–1.40, p = 0.533); however, the impact of PMRT on unanticipated reoperations differed by reconstruction type. In patients who received implant-based reconstructions, PMRT was associated with a 3.05-fold (95% CI 1.20–7.75, p = 0.019) higher odds of unanticipated reoperations, while there was no difference in patients who underwent autologous reconstruction (OR 1.17, 95% CI 0.51–2.66, p = 0.713). Delayed reconstruction or delayed–immediate reconstructions were associated with an increased risk of both overall and unanticipated reoperations in both reconstruction cohorts. Conclusions: PMRT appears to be associated with an increased risk of unanticipated reoperations among patients receiving implant-based reconstruction, but not among those receiving autologous reconstruction. The risk of reoperation should be taken into consideration when selecting the appropriate breast reconstruction type when PMRT is planned.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Development of High-Pressure Multigrain X-Ray Diffraction for Exploring the Earth’s Interior

The lower mantle comprises >55% by volume of our planet and enigmatic seismic features in the deep lower mantle call for interperations from high pressure-temperature (P-T) petrological experiments. Studying phase changes in a realistic bulk composition or with addition of volatiles requires in situ phase identification and structure analysis in a multiphase assemblage under corresponding high P-T conditions. In a powder X-ray diffraction (XRD) pattern, however, peaks of new structures and minor phases are often overshadowed by the diffraction of coexisting major phases. In the past 5 years, we have overcome the difficulties and successfully studied new structures and minor phases in great detail in situ under deep lower manlte conditions applying the multigrain XRD technique that treats each individual 100-500 nm-size grains as a single-crystal in a sample consisting of multiple phases and multiple crystals. This paper summarized the advantages of the multigrain XRD technique and provided an example of identification of hydrous phases with average ~100 nm grain size in a multiphase assemblage through combination of in situ phase identification and ex situ microscopic analysis.

58 GEOSCIENCES↗

Complex interactions between day length and diurnal patterns of gene expression drive photoperiodic responses in a perennial C 4 grass

Abstract Photoperiod is a key environmental cue affecting flowering and biomass traits in plants. Key components of the photoperiodic flowering pathway have been identified in many species, but surprisingly few studies have globally examined the diurnal rhythm of gene expression with changes in day length. Using a cost‐effective 3′‐Tag RNA sequencing strategy, we characterize 9,010 photoperiod responsive genes with strict statistical testing across a diurnal time series in the C 4 perennial grass, Panicum hallii . We show that the vast majority of photoperiod responses are driven by complex interactions between day length and sampling periods. A fine‐scale contrast analysis at each sampling time revealed a detailed picture of the temporal reprogramming of cis ‐regulatory elements and biological processes under short‐ and long‐day conditions. Phase shift analysis reveals quantitative variation among genes with photoperiod‐dependent diurnal patterns. In addition, we identify three photoperiod enriched transcription factor families with key genes involved in photoperiod flowering regulatory networks. Finally, coexpression networks analysis of GIGANTEA homolog predicted 1,668 potential coincidence partners, including five well‐known GI‐interacting proteins. Our results not only provide a resource for understanding the mechanisms of photoperiod regulation in perennial grasses but also lay a foundation to increase biomass yield in biofuel crops.

Weng, Xiaoyu↗

Climatic impact, future biomass production, and local adaptation of four switchgrass cultivars

Abstract Previous studies have shown that switchgrass has a wide range of genetic variation and that productivity is linked to local adaptation to the location of origin for many cultivars. In this meta‐analysis, we compiled and analyzed 900 observations associated with 41 field trials for four switchgrass cultivars (two lowlands, Alamo and Kanlow, and two uplands, Cave‐In‐Rock and Shelter). This extensive dataset and machine learning were used to identify the most influential variables impacting switchgrass productivity, to search for evidence of local adaptation to each cultivar's location of origin, and to predict change in productivity under future climate for each cultivar. In general, variables associated with climate and management are more important predictors of productivity relative to soil variables. Three climatic variables, annual mean temperature, annual precipitation, and precipitation in the wettest month, are identified as key environmental variables for productivity of all cultivars. Productivity under future climate (2041–2060) is predicted to stay stable for all cultivars relative to the prediction under current climate (1986–2005) across all trial locations and over a 20‐year simulation period. However, the productivity of each cultivar varies from location to location and from year to year, although productivity varies more between locations than between years. Additionally, we observe shifts in the most productive cultivar at the local field scale depending on the combination of management practice and climates. The shape of the relationship between productivity and the annual mean temperature relative to the cultivar's location of origin is a bell‐shaped curve for Kanlow, Cave‐in‐Rock, and Shelter, indicative of local adaptation. Identifying influential environmental variables and their relationships to productivity with respect to cultivar's location of origin help predicting productivity on the local field scale, and will help with the biofuel production planning through the selection of suitable cultivars for different locations under climate changes.

59 BASIC BIOLOGICAL SCIENCES↗

Corrosion Resistance of Cu-Ni-Si Alloy Under High-Temperature, High-Pressure H{sub 2}S and Cl{sup −} Environments

In this study, Cu-Ni-Si alloy was subjected to corrosion resistance tests under simulated high-temperature, high-pressure H{sub 2}S and Cl{sup −} environments. The corrosion rates, electrochemical performance, surface morphologies, and chemical compositions of the Cu-Ni-Si alloy after corrosion were analyzed by the mass loss method, electrochemical impedance spectroscopy, scanning electron microscopy, energy-dispersive x-ray spectrometry, and x-ray diffraction. The results showed that, at the initial stage of corrosion, because of the loose corrosion product layer initially formed on the surface, a high corrosion rate was observed for the Cu-Ni-Si alloy under high-temperature, high-pressure environments. With the progress of corrosion, the corrosion rate gradually decreased and reached a steady state. Because at the later stage, a passive film was formed on the alloy surface, further inhibiting the corrosion of the alloy and improved its corrosion resistance. The Cu-Ni-Si alloy exhibited good corrosion resistance under high-temperature, high-pressure H{sub 2}S and Cl{sup −} environments.

36 MATERIALS SCIENCE↗

Dual-Channel Enzymatic Inhibition Measurement (DEIM) Coupling Isotope Substrate via Matrix-Assisted Laser Desorption/Ionization Time of Flight Mass Spectrometry

A novel dual-channel enzymatic inhibition measurement (DEIM) method was developed to improve the repeatability with light/heavy isotope substrates, producing reliable relative standard deviations (< 3%) by employing acetylcholinesterase (AChE) as the model enzyme. The matrix-assisted laser desorption/ionization time of flight mass spectrometry (MALDI-TOF MS) was adapted for enzyme-inhibited method due to its good salt-tolerance and high throughput; meanwhile, dual-channel enzymatic reactions were performed to improve the repeatability of each well. The acetylcholinesterase inhibition measurement was conducted by mixing the quenched enzyme reaction solution of blank group (with heavy isotope as substrate) and experimental group (with light isotope as substrate), of which the inhibition rate might be affected by isotope effects. Hence, inverse study and Km measurement were implemented to validate the method. The inverse study shows similar inhibition rate (68.9 and 70.3%) and the Km of isotope substrates are analogous (0.139 and 0.135 mM), which demonstrated that the novel method is feasible to AChE inhibition measurement. Finally, the method was applied to herb extracts, half of which exhibit inhibition to AChE. The precise dual-channel enzymatic inhibition measurement (DEIM) method could be regarded as a promising approach to potential enzyme inhibitor screening. .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Intraspecific Trait Variation and Phenotypic Plasticity Mediate Alpine Plant Species Response to Climate Change

In a rapidly changing climate, alpine plants may persist by adapting to new conditions. However, the rate at which the climate is changing might exceed the rate of adaptation through evolutionary processes in long-lived plants. Persistence may depend on phenotypic plasticity in morphology and physiology. Here we investigated patterns of leaf trait variation including leaf area, leaf thickness, specific leaf area, leaf dry matter content, leaf nutrients (C, N, P) and isotopes (δ 13C and δ 15N) across an elevation gradient on Gongga Mountain, Sichuan Province, China. We quantified inter- and intra-specific trait variation and the plasticity in leaf traits of selected species to experimental warming and cooling by using a reciprocal transplantation approach. We found substantial phenotypic plasticity in most functional traits where δ 15N, leaf area, and leaf P showed greatest plasticity. These traits did not correspond with traits with the largest amount of intraspecific variation. Plasticity in leaf functional traits tended to enable plant populations to shift their trait values toward the mean values of a transplanted plants’ destination community, but only if that population started with very different trait values. These results suggest that leaf trait plasticity is an important mechanism for enabling plants to persist within communities and to better tolerate changing environmental conditions under climate change.

54 ENVIRONMENTAL SCIENCES↗

Effect of Ti on structure and soft magnetic properties of Si-rich Finemet-type nanocrystalline Fe73.5Cu1Nb3-xSi17.5B5Tix alloys

Highlights: • Substitution of Nb by Ti can reduce the T{sub x1} and enlarge the ΔT{sub x}. • Fe{sub 73.5}Cu{sub 1}Nb{sub 2}Si{sub 17.5}B{sub 5}Ti{sub 1} alloy exhibits high μ{sub i} of 18,000 and low H{sub c} of 0.54 Oe. • Magnetic properties were analysed in terms of the relationship between H{sub c} and μ{sub i}. • Soft magnetic properties will deteriorate when Nb is completely replaced by Ti. • The reasons of variation of permeability at high temperature were analyzed. - Abstract: Fe{sub 73.5}Cu{sub 1}Nb{sub 3-x}Si{sub 17.5}B{sub 5}Ti{sub x} (x = 0, 1, 2, 3) amorphous alloys were prepared by the single roller melt spinning method. The effects of Ti substitution for Nb on the crystallization behavior, microstructure and soft magnetic properties were investigated. Compared to the previously reported Finemet alloy, the onset primary crystallization temperature T{sub x1} becomes lower which has dropped from 803K to 758K. The crystallization temperature interval ΔT{sub x} increases from 468K to 488K as the x increases from 0 to 3. However, the Curie temperature of amorphous phase shows a downward tendency with the increase of Ti content. Compared to the previously reported Finemet alloy, the μ{sub i} increases obviously to more than 18,000 at x = 1, the H{sub c} decreases from 0.59 Oe to 0.54 Oe. When Ti replaces Nb completely, the optimum annealing temperature range for precipitating single soft magnetic phase is enlarged, but the permeability at room- and high-temperature is deteriorated, the reason of which was also analysed.

77 NANOSCIENCE AND NANOTECHNOLOGY↗