Engineering Papers⌕ Search

Engineering topics

Zhang, L.

Publications and source records attributed to Zhang, L..

At least 73 records · Page 4

Hot Corrosion Performance of Single-Crystal CMSX-4 and CMSX-486 Superalloys in the Mixture of Na{sub 2}SO{sub 4}-NaCl Melts

A modification in the chemistry of single-crystal CMSX-4 to produce CMSX-486 superalloy has been reported in the literature to be accomplished without degradation in high-temperature mechanical performance. However, adequate attention has not yet been focussed on the hot corrosion response of the alloy considering its chemical composition modification. This paper reports for the first time that a considerable degradation in the hot corrosion resistance of CMSX-4 occurs by the modification of its chemistry. Corrosion tests at different salt concentrations and temperatures showed that the hot corrosion resistance of CMSX-486 is worse than the conventional CMSX-4 alloy. The difference in the corrosion resistance characteristics of the two alloys is attributable to the nature of the protective oxide layer formed on the materials during hot corrosion. Characterization using various advanced techniques revealed that the oxide layer formed on CMSX-486 consists of less amount of protective and coherent Al{sub 2}O{sub 3} and Cr{sub 2}O{sub 3} film than CMSX-4, and this is the reason for its poor hot corrosion resistance.

36 MATERIALS SCIENCE↗

Advances in plasma–wall interaction control for H-mode operation over 100 s with ITER-like tungsten divertor on EAST

A total power injection up to 0.3 GJ has been achieved in EAST long pulse H-mode operation of 101.2 s with an ITER-like water-cooled tungsten (W) mono-block divertor, which has steady-state power exhaust capability of 10 MWm –2 . The peak temperature of W target saturated at 12 s to the value T ~ 500 °C with a heat flux ~3.3 MW m –2 being maintained during the discharge. By tailoring the 3D divertor plasma footprint through edge magnetic topology change, the heat load was broadly dispersed and thus peak heat flux and W sputtering were well controlled. Active feedback control of H-mode detachment with D 2 fuelling or divertor impurity seeding has been achieved successfully, with excellent compatibility with the core plasma performance. Active feedback control of radiative power utilizing neon seeding was achieved with f rad = 18%–41% in H-mode operation, exhibiting potential for heat flux reduction with divertor and edge radiation. This has been further demonstrated in DIII-D high β P H-mode scenario within the joint DIII-D/EAST experiment using impurity seeding from the divertor volume. Steady-state particle control and impurity exhaust has been achieved for long pulse H-mode operation over 100 s with the W divertor by leveraging the effect of drifts and optimized divertor configuration, coupled with strong pumping and extensive wall conditioning. Methods toward the reduction of divertor W sourcing, which is of crucial importance for a metal-wall tokamak, are also explored. These advances provide vital experimental information on favourable core-edge integration for high power, long-pulse H-mode operation in EAST, ITER and CFETR.

43 PARTICLE ACCELERATORS↗

Energy occupation of waves and structures in 3D compressive MHD turbulence

Abstract Structures and propagating waves are often observed in solar wind turbulence. Their origins and features remain to be uncovered. In this work, we use 3D driven, compressible MHD turbulence simulations to investigate the global signatures of the driven fluctuations in whole spatial and temporal domain. With four-dimensional spatial-temporal (x, y, z, t) Fourier transformations implemented, we have identified two distinct main populations: waves, which satisfy the $\omega -\boldsymbol {k}$ dispersion relations and are propagating; and structures, which satisfy the polarization relations but non-propagating (ω = 0). Whereas the overall turbulent energy spectrum is still consistent with k−5/3, the contributions from waves and structures show very different behaviour in $\boldsymbol {k}$ space, with structures dominating at small k but waves becomes comparable to structures at large k. Overall, the fluctuations in the directions perpendicular to the large-scale mean field $\boldsymbol {B_0}$ are a manifestation of structures, while along the parallel direction, the fluctuations are dominated by waves. Also, a significant portion of the incompressible structures are the Alfvénic nature, and with imbalanced increased, the waves predominantly propagate in one direction and nearly perpendicular to $\boldsymbol {B_0}$. Differentiating the relative contributions from waves and structures could have important implications for understanding the non-linear cascade processes in the inertial range as well as particle-fluctuation interactions at small scales.

Yang, L. P.↗

Promising High-Confinement Regime for Steady-State Fusion

A reproducible stationary high-confinement regime with small “edge-localized modes” (ELMs) has been achieved recently in the Experimental Advanced Superconducting Tokamak, which has a metal wall and low plasma rotation as projected for a fusion reactor. Here, we have uncovered that this small ELM regime is enabled by a wide edge transport barrier (pedestal) with a low density gradient and a high density ratio between the pedestal foot and top. Nonlinear simulations reveal, for the first time, that the underlying mechanism for the observed small ELM crashes is the upper movement of the peeling boundary induced by an initial radially localized collapse in the pedestal, which stops the growth of instabilities and further collapse of the pedestal, thus providing a physics basis for mitigating ELMs in future steady-state fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Magnetic transition and defect characteristics of multiferroic CuFe1-xGaxO2 studied by positron annihilation spectra

Highlights: • A systematic investigation of the effect of Ga doping on the structural and magnetic properties of CuFeO{sub 2}. • Crystal defects are determined by positron annihilation spectroscopy. • There is a good correlation between antiferromagnetic stability and lattice distortion. • Crystal defects and interlayer ions in polycrystalline samples influence the magnetic properties. - Abstract: The structure, crystal defects and magnetic properties of multiferroic CuFe{sub 1-x}Ga{sub x}O{sub 2} (CFGO; x = 0–0.07) ceramics are studied systemically. Substitution of Ga{sup 3+} for Fe{sup 3+} shrinks the CFO lattice, decreases the particle size, and causes small liquid phase formation. Positron annihilation spectroscopy demonstrates that all samples contain a considerable number of vacancy defects. The overall defect environment is virtually unaffected by Ga{sup 3+} doping, but the open-volume of the defects is redistributed. Magnetic susceptibility measurements show that Ga doping enhances the strength of the antiferromagnetic interaction between high-spin Fe{sup 3+} ions as a result of reduced magnetic correlation length, but decrease the stability of the antiferromagnetic phase. The antiferromagnetic transition temperature, T{sub N2}, decreases from 11 K for x = 0 to 8 K for x = 0.07, and this destabilization of the antiferromagnetic phase is closely related to the crystal structure and defects, which are discussed in detail in this work.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Results from an improved flowing liquid lithium limiter with increased flow uniformity in high power plasmas in EAST

Significant engineering and physic progress was made by the upgrade of a flowing liquid lithium limiter (FLiLi) inserted into EAST H-mode discharges in 2016. The progress includes an improvement of liquid Li coverage uniformity, no macroscopic surface erosion by plasma materials interaction, effective removal of 55% of the discharge heat flux using high pressure He cooling during ohmic discharges, and the demonstrated ability to restart Li flow for a second experiment performed a week after the first. With increasing Li flow rate, fuel particle recycling and Fe impurity radiation gradually decreased, and plasma performance slightly improved, but there was no impact on the edge tungsten influx. No obvious Li bursts appeared during operation with up to about 4.5 MW auxiliary heating power with peak heat flux reaching ~4 MW m –2 on FLiLi. In addition, a gradual mitigation of edge localized mode (ELM) activity was observed with FLiLi operation. Lastly, short-lived ELM-free phases were observed for the first time in EAST during FLiLi insertion, with increasing τ E and transient H 98(y, 2) < 2.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Real-time reduction of tungsten impurity influx using lithium powder injection in EAST

We report the first successful use of solid material injection, in powder form, to reduce core tungsten impurities in EAST discharges with tungsten divertor plasma-facing components. Tungsten is the leading plasma-facing material for use in ITER as well as future fusion devices. However, tungsten sometimes accumulates in the plasma core of fusion devices, which is an impediment to the achievement of high-power, long-pulse H-modes. In this work, tungsten impurity influx from the tungsten divertor was reduced by real-time injection of lithium powder into EAST discharges. An increase in stored energy and confinement accompanied the sharp reduction of core tungsten with real-time lithium powder injection in L-mode discharges. In H-mode discharges, real-time lithium powder injection reduced the tungsten core impurity emission while also mitigating ELMs. During powder injection, the divertor electron temperature was reduced, which reduced the tungsten source. In conclusion, the tungsten impurity emission remained low in discharges even after active lithium injection was terminated, a signature of improved and lasting wall conditioning in the tungsten divertor.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

TES X-ray Spectrometer at SLAC LCLS-II

We are building a transition edge sensor (TES) X-ray spectrometer for the Linac Coherent Light Source (LCLS-II) at SLAC National Accelerator Laboratory (SLAC) to coincide with new upgrades for this free electron laser facility. This new X-ray spectrometer will have 1000 TES pixels with 0.5 eV energy resolution for soft X-rays below 1 keV. Multiplexing will be done with microwave SQUID resonators and new specialized electronic hardware developed at SLAC. This spectrometer will use a dilution refrigerator to achieve lower operating temperatures than previous TES spectrometers and will be coupled to the liquid jet endstation at LCLS-II. The spectrometer is designed to operate at much higher count rates than previous TES X-ray spectrometers to take advantage of the high repetition rate of the LCLS-II. Science applications will utilize the high photon collection efficiency and throughput, high energy resolution, as well as its ability to simultaneously measure its full calibrated energy range.

47 OTHER INSTRUMENTATION↗

The beamline ID32 at the ESRF for soft X-ray high energy resolution resonant inelastic X-ray scattering and polarisation dependent X-ray absorption spectroscopy

Here, the ID32 Soft X-ray Beamline line is an ESRF upgrade beamline for X-ray absorption (XAS) and Resonant Inelastic X-ray Scattering (RIXS) spectroscopic studies. It was opened to Users in October 2014 and provides polarised soft X-rays in the 400–1600 eV energy range. It has two branches: One branch has been designed for X-ray magnetic dichroism experiments, both linear (XMLD) and circular (XMCD), with high sensitivity, reproducibility, flexibility, user friendliness and the capability for fast energy scanning. The X-ray beam is available in two experimental areas, one with a dedicated superconducting high field magnet and a sample preparation facility, the second area being open for User instruments. The other branch is dedicated to very high energy resolution Resonant Inelastic X-ray Scattering experiments with a combined resolving power up to 30 000 around 930 eV. A scattering arm which is continuously variable under UHV vacuum over 100 degrees and a four-circle sample goniometer allows accurate positioning of the sample to enable 3D mapping of q space. Combined with the possibility of polarisation analysis of the outgoing photons the beamline provides a state-of-the-art soft X-ray RIXS facility.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Activation of ultrathin SrTiO 3 with subsurface SrRuO 3 for the oxygen evolution reaction

Here, water electrolysis occurs via the oxygen/hydrogen evolution reactions. Achieving sufficiently high oxygen evolution reaction (OER) activity while maintaining stability of the active catalyst surface is a primary challenge of designing OER catalysts. Often high electrocatalytic activity is accompanied by structural instability. This is the case for the metallic perovskite oxide SrRuO 3 (SRO), which exhibits rapid dissolution under OER conditions, both as thin-films and as nanoparticles. On the other hand, large band-gap perovskite oxides such as SrTiO 3 (STO) are inactive for OER in the dark but are stable. In this work, we demonstrate that burying as little as one unit cell of SRO beneath an ultrathin STO capping layer activates the otherwise inert electrocatalyst and gives excellent stability. Using density functional theory (DFT) calculations, we find that such a chemical modification of STO by sub-surface SRO introduces new 4d electronic states including Ru states within the STO band gap, raising the energy level of the electrons, changing the electronic hybridization, and facilitating an easy transfer to the adsorbed intermediates. We validate this hypothesis experimentally using atomically precise heteroepitaxial deposition. We find that a single-unit-cell layer of SRO is sufficient to activate the topmost STO layer towards OER; burying SRO underneath two unit cells of STO protects the inherently unstable SRO against corrosion during OER. Generally, our layered heterostructures are model systems of oxide core–shell structures, where an unstable catalyst (core) is protected against degradation and electronically activates the otherwise inactive shell. As demonstrated in this work, the growth of ultrathin heterostructures establishes a rigorous platform for screening core/shell nanoparticle combinations/thicknesses, and elucidates sub-surface activation mechanism for achieving stable and active oxide electrocatalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Unfolding neutron spectrum with Markov Chain Monte Carlo at MIT research Reactor with He-3 Neutral Current Detectors [Measuring neutron spectrum at MIT research reactor utilizing He-3 Bonner Cylinder Approach with an unfolding analysis]

Here, the Ricochet experiment seeks to measure Coherent (neutral-current) Elastic Neutrino-Nucleus Scattering (CEνNS) using dark-matter-style detectors with sub-keV thresholds placed near a neutrino source, such as the MIT (research) Reactor (MITR), which operates at 5.5 MW generating approximately 2.2 × 10 18 ν/second in its core. Currently, Ricochet is characterizing the backgrounds at MITR, the main component of which comes in the form of neutrons emitted from the core simultaneous with the neutrino signal. To characterize this background, we wrapped Bonner cylinders around a 3 2 He thermal neutron detector, whose data was then unfolded via a Markov Chain Monte Carlo (MCMC) to produce a neutron energy spectrum across several orders of magnitude. We discuss the resulting spectrum and its implications for deploying Ricochet at the MITR site as well as the feasibility of reducing this background level via the addition of polyethylene shielding around the detector setup.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

First-Principles Investigation of Equiatomic Quaternary Heusler Alloys NbVMnAl and NbFeCrAl and a Discussion of the Generalized Electron-Filling Rule

Plane-wave pseudo-potential methods based on density functional theory are used to study the electronic structures, magnetic, and half-metallic properties of the equiatomic quaternary Heusler alloys NbVMnAl and NbFeCrAl. Calculated results reveal that NbVMnAl and NbFeCrAl alloys are newly designed half-metallic ferrimagnets with a total magnetic moment (M{sub t}) of 2 μ{sub B}. We found that the Slater-Pauling rule, i.e., the relationship between the M{sub t} and the total number of valence electrons (Z{sub t}) of these two alloys was different. For NbVMnAl alloy, it obeys the M{sub t} = |Z{sub t} − 18| rule. For NbFeCrAl, it satisfies the M{sub t} = |Z{sub t} − 24| rule. Also, we observed that the half-metallic band gap (HM-BG) of these two alloys was different. Namely, for one material (NbFeCrAl), it is located in the spin-up channel, and in the other (NbVMnAl), it is located in the spin-down channel. To explain these phenomena, in this work, the generalized electron-filling rule was investigated, and the origin of the HM-BG of NbVMnAl and NbFeCrAl was studied. We hope that our work may provide theoretical guidance in searching for Nb-based equiatomic quaternary Heusler half-metals in the future.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Continuing Efforts on Efficiency and Performance Improvement of mdtmFTP

mdtmFTP is a high-performance data transfer tool: • Pipelined I/O-centric design to streamline data transfer • Multicore-aware data transfer middleware (MDTM) optimizes use of underlying multicore system • Extremely efficient in transferring of Lots Of Small Files • Various optimization mechanisms including Asynchronous I/O and Batch processing. • Sponsored by DOE/SC/ASCR. http://mdtm.fnal.gov $\bullet$Continuing efforts on efficiency and Performance Improvement: • Refactoring event queue mechanism • I/O optimization • Scalability evaluation

Zhang, L.↗

Quality Assurance on Undoped CsI Crystals for the Mu2e Experiment

The Mu2e experiment is constructing a calorimeter consisting of 1,348 undoped CsI crystals in two disks. Each crystal has a dimension of 34 x 34 x 200 mm 3 , and is readout by a large area silicon PMT array. A series of technical specifications was defined according to physics requirements. Preproduction CsI crystals were procured from three firms: Amcrys, Saint-Gobain and Shanghai Institute of Ceramics. We report the quality assurance on crystal's scintillation properties and their radiation hardness against ionization dose and neutrons. With a fast decay time of 30 ns and a light output of more than 100 p.e./MeV measured with a bi-alkali PMT, undoped CsI crystals provide a cost-effective solution for the Mu2e experiment.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗