Engineering Papers⌕ Search

Engineering topics

Zhang, Jun

Publications and source records attributed to Zhang, Jun.

At least 91 records · Page 5

Influence of Melt Superheating Treatment on Solidification Characteristics and Rupture Life of a Third-Generation Ni-Based Single-Crystal Superalloy

The influence of melt superheating treatment on the melt properties, solidification characteristics, and rupture life of a third-generation Ni-based single-crystal superalloy was investigated to reveal the critical temperature range of melt structure evolution and its effect on rupture life. The results showed that the viscosity of superalloy decreased but the surface tension increased with increasing superheating temperature. Two characteristic temperature points where the melt viscosity and undercooling degree suddenly change were determined to be 1600 °C and 1700 °C, respectively. Similarly, the stability of the solidification interface firstly improved and then weakened with increasing superheating temperature. The dendrite arms were well refined and the segregation was reduced at 1700 °C. In addition, the rupture life obtained at 1100 °C and 137 MPa increased by approximately 30 pct, approaching the rupture life of the corresponding superalloy containing 2 pct Ru, with increasing superheating temperature from 1500 °C to 1700 °C. When the melt was further heated to 1800 °C, the rupture life decreased. The evolutions of solidification characteristics and rupture life with increasing melt superheating temperature were attributed to changes in the melt structure.

36 MATERIALS SCIENCE↗

ST6GAL1 negatively regulates monocyte transendothelial migration and atherosclerosis development

Highlights: • ST6GAL1 expression is inversely related to atherosclerosis development. • Knockdown of ST6GAL1 in vascular endothelial cells directly promotes monocyte transendothelial migration. • ST6GAL1 overexpression inhibits TNFα-induced monocyte transendothelial migration. • β-catenin sialylation level is downregulated in inflammatory endothelial cells. Monocyte transendothelial migration is a critical step in the initial stage of atherosclerosis, in which the involvement of α-2,6 sialyltransferase 1 (ST6GAL1) has been confirmed by increasing evidence. But the direct relationship between ST6GAL1 and atherosclerosis remains incompletely uncertain. In this study, we demonstrated that the expression level of ST6GAL1 in vascular endothelium was significantly decreased in atherosclerosis development process, while obviously recovered after atherosclerosis regression. Further analysis showed that knockdown of ST6GAL1 by RNA interference in vascular endothelial cells EA. hy926 obviously promoted TNFα-triggered monocyte-transendothelial migration, whereas overexpression of ST6GAL1 strongly inhibited monocyte-transendothelial migration. Moreover, we firstly found β-catenin is a sialylated protein and its sialylation level is decreased in TNFα-treated EA. hy926 cells, suggesting that the function of ST6GAL1 in preventing both atherosclerosis development and monocyte transendothelial migration might result from the sialylation of β-catenin of endothelium. Our results suggested ST6GAL1 might be a potential target for atherosclerosis prevention and treatment.

60 APPLIED LIFE SCIENCES↗

Chitosan oligosaccharides enhance lipid droplets via down-regulation of PCSK9 gene expression in HepG2 cells

Highlights: • COS enhance lipid droplets in HepG2 cells. • COS down-regulate the expression of PCSK9 to maintain hepatic LDLR abundance and activity. • COS inhibit HNF1α and SREBP-2 activity leading to down-regulation of PCSK9. Chitosan oligosaccharides (COS), linear polymers of N-acetyl-D-glucosamine and deacetylated glucosamine, exhibit diverse pharmacological effects such as antimicrobial, antitumor, antioxidant and anti-inflammatory activities. Here, we explored their hypocholesterolemic effects in vivo and the molecular mechanisms of COS in hepatic cells. Our in vivo study of dyslipidemic ApoE{sup -/-} male mice showed that COS treatment of 500 mg kg{sup −1} d{sup −1} for 4 weeks clearly reduced the lipid deposits in the aorta and significantly decreased the hepatic proprotein convertase subtilisin/kexin type 9 (PCSK9) protein levels versus HFD groups (p < 0.05). To elucidate the mechanisms behind these effects, the HepG2 cell line was treated with COS. We found that COS (200 μg/ml) increased the amount of cell-surface low-density lipoprotein receptor (LDLR) and enhanced the lipid droplets in HepG2 cells (p < 0.05). The mRNA levels of LDLR and HMG-CoA protein levels were not altered, and the mRNA levels of PCSK9 were down-regulated by COS treatment for 24 h. We also observed that the expression levels of SREBP-2 (125 kD) and HNF-1α were increased in total cell lysates, but nuclear SREBP-2 (nSREBP-2, 68 kD, the active subunit of SREBP-2) levels were decreased and FOXO3a levels increased in nuclear lysates after COS treatment for 24 h. We demonstrated that one of the reasons for regulation of lipid transfer with COS is that FOXO3a levels are up-regulated by COS, leading to a reduction in the PCSK9 promoter binding capacity of HNF-1α and thus suppressing PCSK9 gene expression, up-regulating LDLR levels, and enhancing the lipid droplets in HepG2 cells. In addition, decreased expression of the PCSK9 gene was also contributed to by down-regulation of SREBP-2 by COS. We further confirmed the effect of suppression of PCSK9 expression by COS by utilizing RNA interference to silence HNF-1α and SREBP-2. Finally, to the best of our knowledge, we are the first to demonstrate that PCSK9 expression and LDLR activity are synergistically changed by a combination of HNF-1α and SREBP-2 after COS treatment. Our findings indicate that COS may regulate PCSK9 to modulate hepatic LDLR abundance and activity.

60 APPLIED LIFE SCIENCES↗

Negative influence of rafted γ′ phases on 750 °C/750 MPa creep in a Ni-based single crystal superalloy with 4% Re addition

Highlights: • The negative influence of the rafted γ′ phases on creep was investigated. • The rafted sample exhibited a lower creep rate a shorter rupture life. • Fine γ′ phases impeded first the dislocation movement in γ matrix. • Existed superdislocations and the stress release decreased the creep resistance. • Rafted γ′ phases were more easily cut by superdislocations and stacking faults. - Abstract: Specimens with two different γ′ phase microstructures, named as-heat treated sample with cuboidal γ′ phases and pre-rafted sample with N-type rafted γ′ phases, were compared to investigate the negative influence of the rafted γ′ phases on the creep property in a Ni-based single crystal superalloy with 4% Re addition at 750 °C and 750 MPa condition. The results indicated that the sample with cuboidal γ′ phases exhibited a lower creep rate and a longer rupture life compared to that with rafted γ′ phases. Transmission electron microscope examinations showed that lots of fine γ′ phases impeded first the dislocation movement in the channel of γ matrix in the initial primary creep stage before the cuboidal γ′ phases were cut by stacking faults in as-heat treated sample. However, in pre-rafted sample, some existed superdislocations located in rafted γ′ phases and the mismatch stress release at γ/rafted γ′ interface resulting from pre-rafted treatment not only decreased the creep resistance of rafted γ′ phases, but also weakened the γ/rafted γ′ interface pinning effect for dislocation movement. Therefore, the rafted γ′ phases were easily cut by superdislocations and stacking faults resulting in a higher creep rate and a shorter creep life.

36 MATERIALS SCIENCE↗

Optimal Power Scheduling for a Medium Voltage AC/DC Hybrid Distribution Network

With the great increase of renewable generation as well as the DC loads in the distribution network; DC distribution technology is receiving more attention; since the DC distribution network can improve operating efficiency and power quality by reducing the energy conversion stages. This paper presents a new architecture for the medium voltage AC/DC hybrid distribution network; where the AC and DC subgrids are looped by normally closed AC soft open point (ACSOP) and DC soft open point (DCSOP); respectively. The proposed AC/DC hybrid distribution systems contain renewable generation (i.e., wind power and photovoltaic (PV) generation); energy storage systems (ESSs); soft open points (SOPs); and both AC and DC flexible demands. An energy management strategy for the hybrid system is presented based on the dynamic optimal power flow (DOPF) method. The main objective of the proposed power scheduling strategy is to minimize the operating cost and reduce the curtailment of renewable generation while meeting operational and technical constraints. The proposed approach is verified in five scenarios. The five scenarios are classified as pure AC system; hybrid AC/DC system; hybrid system with interlinking converter; hybrid system with DC flexible demand; and hybrid system with SOPs. Results show that the proposed scheduling method can successfully dispatch the controllable elements; and that the presented architecture for the AC/DC hybrid distribution system is beneficial for reducing operating cost and renewable generation curtailment.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Lixisenatide reduces amyloid plaques, neurofibrillary tangles and neuroinflammation in an APP/PS1/tau mouse model of Alzheimer's disease

Highlights: • Lixisenatide reduced amyloid plaques, neurofibrillary tangles and neuroinflammation. • Activiation of PKA-CREB and inhibition of p38-MAPK were the protective mechanisms. • Lixisenatide might have the potential to be developed as a novel therapy for AD. Type 2 diabetes mellitus (T2DM) has been identified as a high risk factor for Alzheimer's disease (AD). The impairment of insulin signaling has been found in AD brain. Glucagon-like peptide-1 (GLP-1) is an incretin hormone, normalises insulin signaling and acts as a neuroprotective growth factor. We have previously shown that the long-lasting GLP-1 receptor (GLP-1R) agonist lixisenatide plays an important role in memory formation, synaptic plasticity and cell proliferation of rats. In the follow-up study, we analysed the neuroprotective effect and mechanism of lixisenatide, injected for 60 days at 10 nmol/kg i.p. once daily in APP/PS1/tau female mice and C57BL/6J female mice (as control) aged 12 month. The results showed that lixisenatide could reduce amyloid plaques, neurofibrillary tangles and neuroinflammation in the hippocampi of 12-month-old APP/PS1/tau female mice; activation of PKA-CREB signaling pathway and inhibition of p38-MAPK might be the important mechanisms in the neuroprotective function of lixisenatide. The study demonstrated that GLP-1R agonists such as lixisenatide might have the potential to be developed as a novel therapy for AD.

60 APPLIED LIFE SCIENCES↗

Submicron silica as high−capacity lithium storage material with superior cycling performance

Highlights: • The electrochemical performance of SiO{sub 2} is strongly associated with ball milling. • Submicron silica show superior cycling performance for lithium storage. • Mechanism of electrochemical performance of SiO{sub 2} depended on milling was discussed. - Abstract: Submicron silica (SiO{sub 2}) is prepared via directly milling bulk SiO{sub 2}, which is the major constituent of the abundant sand on the earth. The electrochemical lithium storage performance of SiO{sub 2} is found to be strongly associated with the ball milling treatment. The reversible capacity of SiO{sub 2} gradually increases from 163 to 803 mAh g{sup −1} as the milling time is extended from 0 to 72 h. For the SiO{sub 2} milled for 24 h, it exhibits excellent cycling performance with a discharge capacity of 602 mAh g{sup −1} over 150 cycles, corresponding to the capacity retention of 99.8% relative to the 2nd cycle. The different particle sizes distribution and electrochemical activity of SiO{sub 2} are responsible for the effect of ball milling on its electrochemical lithium storage performance such as reversible capacity, cycling stability, electrode polarization and initial Coulombic efficiency.

36 MATERIALS SCIENCE↗

Block-induced Complex Structures Building the Flare-productive Solar Active Region 12673

Solar active region (AR) 12673 produced 4 X-class, 27 M-class, and numerous lower-class flares during its passage across the visible solar disk in 2017 September. Our study is to answer the questions why this AR was so flare-productive and how the X9.3 flare, the largest one of the past decade, took place. We find that there was a sunspot in the initial several days, and then two bipolar regions emerged nearby it successively. Due to the standing of the pre-existing sunspot, the movement of the bipoles was blocked, while the pre-existing sunspot maintained its quasi-circular shaped umbra only with the disappearance of a part of penumbra. Thus, the bipolar patches were significantly distorted, and the opposite polarities formed two semi-circular shaped structures. After that, two sequences of new bipolar regions emerged within the narrow semi-circular zone, and the bipolar patches separated along the curved channel. The new bipoles sheared and interacted with the previous ones, forming a complex topological system, during which numerous flares occurred. At the highly sheared region, a great deal of free energy was accumulated. On September 6, one negative patch near the polarity inversion line began to rapidly rotate and shear with the surrounding positive fields, and consequently the X9.3 flare erupted. Our results reveal that the block-induced complex structures built the flare-productive AR and the X9.3 flare was triggered by an erupting filament due to the kink instability. To better illustrate this process, a block-induced eruption model is proposed for the first time.

79 ASTRONOMY AND ASTROPHYSICS↗

Low-Frequency Shear and Layer-Breathing Modes in Raman Scattering of Two-Dimensional Materials

Ever since the isolation of single-layer graphene in 2004, two-dimensional layered structures have been among the most extensively studied classes of materials. To date, the pool of two-dimensional materials (2DMs) continues to grow at an accelerated pace and already covers an extensive range of fascinating and technologically relevant properties. An array of experimental techniques have been developed and used to fully characterize and understand these properties. In particular, Raman spectroscopy has proven to be a key experimental technique, thanks to its capability to identify minute structural and electronic effects in nondestructive measurements. While high-frequency (HF) intralayer Raman modes have been extensively employed for 2DMs, recent experimental and theoretical progress has demonstrated that low-frequency (LF) interlayer Raman modes are more effective at determining layer numbers and stacking configurations, and provide a unique opportunity to study interlayer coupling. These advantages are due to 2DMs’ unique interlayer vibration patterns where each layer behaves as an almost rigidly moving object with restoring forces corresponding to weak interlayer interactions. Compared to HF Raman modes, the relatively small attention originally devoted to LF Raman modes is largely due to their weaker signal and their proximity to the strong Rayleigh line background, which previously made their detection challenging. Recent progress in Raman spectroscopy with technical and hardware upgrades now makes it possible to probe LF modes with a standard single-stage Raman system and has proven crucial to characterize and understand properties of 2DMs. Here, we present a comprehensive and forward-looking review on the current status of exploiting LF Raman modes of 2DMs from both experimental and theoretical perspectives, revealing the fundamental physics and technological significance of LF Raman modes in advancing the field of 2DMs. We review a broad array of materials, with varying thickness and stacking configurations, discuss the effect of in-plane anisotropy, and present a generalized linear chain model and interlayer bond polarizability model to rationalize the experimental findings. We also discuss the instrumental improvements of Raman spectroscopy to enhance and separate LF Raman signals from the Rayleigh line. Lastly, we highlight the opportunities and challenges ahead in this fast-developing field.

36 MATERIALS SCIENCE↗

Flare Ribbons Approach Observed by the Interface Region Imaging Spectrograph and the Solar Dynamics Observatory

We report flare ribbons approach (FRA) during a multiple-ribbon M-class flare on 2015 November 4 in NOAA AR 12443, obtained by the Interface Region Imaging Spectrograph and the Solar Dynamics Observatory. The flare consisted of a pair of main ribbons and two pairs of secondary ribbons. The two pairs of secondary ribbons were formed later than the appearance of the main ribbons, with respective time delays of 15 and 19 minutes. The negative-polarity main ribbon spread outward faster than the first secondary ribbon with the same polarity in front of it, and thus the FRA was generated. Just before their encounter, the main ribbon was darkening drastically and its intensity decreased by about 70% in 2 minutes, implying the suppression of main-phase reconnection that produced two main ribbons. The FRA caused the deflection of the main ribbon to the direction of secondary ribbon with a deflection angle of about 60°. A post-approach arcade was formed about 2 minutes later and the downflows were detected along the new arcade with velocities of 35–40 km s{sup −1}, indicative of the magnetic restructuring during the process of FRA. We suggest that there are three topological domains with footpoints outlined by the three pairs of ribbons. Close proximity of these domains leads to deflection of the ribbons, which is in agreement with the magnetic field topology.

79 ASTRONOMY AND ASTROPHYSICS↗

Simultaneous Observations of p-mode Light Walls and Magnetic Reconnection Ejections above Sunspot Light Bridges

Recent high-resolution observations from the Interface Region Imaging Spectrograph reveal bright wall-shaped structures in active regions (ARs), especially above sunspot light bridges. Their most prominent feature is the bright oscillating front in the 1400/1330 Å channel. These structures are named light walls and are often interpreted to be driven by p-mode waves. Above the light bridge of AR 12222 on 2014 December 06, we observed intermittent ejections superimposed on an oscillating light wall in the 1400 Å passband. At the base location of each ejection, the emission enhancement was detected in the Solar Dynamics Observatory 1600 Å channel. Thus, we suggest that in wall bases (light bridges), in addition to the leaked p-mode waves consistently driving the oscillating light wall, magnetic reconnection could happen intermittently at some locations and eject the heated plasma upward. Similarly, in the second event occurring in AR 12371 on 2015 June 16, a jet was simultaneously detected in addition to the light wall with a wave-shaped bright front above the light bridge. At the footpoint of this jet, lasting brightening was observed, implying magnetic reconnection at the base. We propose that in these events, two mechanisms, p-mode waves and magnetic reconnection, simultaneously play roles in the light bridge, and lead to the distinct kinetic features of the light walls and the ejection-like activities, respectively. To illustrate the two mechanisms and their resulting activities above light bridges, in this study we present a cartoon model.

79 ASTRONOMY AND ASTROPHYSICS↗

Distributed Electrical Energy Systems: Needs, Concepts, Approaches and Vision

Intelligent distributed electrical energy systems (IDEES) are featured by vast system components, diversifled component types, and difficulties in operation and management, which results in that the traditional centralized power system management approach no longer flts the operation. Thus, it is believed that the blockchain technology is one of the important feasible technical paths for building future large-scale distributed electrical energy systems. An IDEES is inherently with both social and technical characteristics, as a result, a distributed electrical energy system needs to be divided into multiple layers, and at each layer, a blockchain is utilized to model and manage its logic and physical functionalities. The blockchains at difierent layers coordinate with each other and achieve successful operation of the IDEES. Speciflcally, the multi-layer blockchains, named 'blockchain group', consist of distributed data access and service blockchain, intelligent property management blockchain, power system analysis blockchain, intelligent contract operation blockchain, and intelligent electricity trading blockchain. It is expected that the blockchain group can be self-organized into a complex, autonomous and distributed IDEES. In this complex system, frequent and in-depth interactions and computing will derive intelligence, and it is expected that such intelligence can bring stable, reliable and efficient electrical energy production, transmission and consumption.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Weak-lensing Power Spectrum Reconstruction by Counting Galaxies. I. The ABS Method

We propose an analytical method of blind separation (ABS) of cosmic magnification from the intrinsic fluctuations of galaxy number density in the observed galaxy number density distribution. The ABS method utilizes the different dependences of the signal (cosmic magnification) and contamination (galaxy intrinsic clustering) on galaxy flux to separate the two. It works directly on the measured cross-galaxy angular power spectra between different flux bins. It determines/reconstructs the lensing power spectrum analytically, without assumptions of galaxy intrinsic clustering and cosmology. It is unbiased in the limit of an infinite number of galaxies. In reality, the lensing reconstruction accuracy depends on survey configurations, galaxy biases, and other complexities due to a finite number of galaxies and the resulting shot noise fluctuations in the cross-galaxy power spectra. We estimate its performance (systematic and statistical errors) in various cases. We find that stage IV dark energy surveys such as Square Kilometre Array and Large Synoptic Survey Telescope are capable of reconstructing the lensing power spectrum at z≃1 and ℓ≲5000 accurately. This lensing reconstruction only requires counting galaxies and is therefore highly complementary to cosmic shear measurement by the same surveys.

79 ASTRONOMY AND ASTROPHYSICS↗