Engineering Papers⌕ Search

Engineering topics

Zhang, He

Publications and source records attributed to Zhang, He.

At least 55 records · Page 3

DECOUPLING AND MATCHING OF ELECTRON COOLING SECTION IN THE MEIC ION COLLIDER RING

To get a luminosity level of 10-33 cm-2sec-1 at all design points of the MEIC, small transverse emittance is necessary in the ion collider ring, which is achieved by an electron cooling. And for the electron cooling, two solenoids are used to create a cooling environment of temperature exchange between electron beam and ion beam. However, the solenoids can also give coupling and matching problem to the optics of the MEIC ion ring lattice. Both of them will have influences on the IP section and other areas, especially for the beam size, Twiss parameters, and nonlinear effects. A symmetric and flexible method is used to deal with these problems. With this method, the electron cooling section is merged into the ion ring lattice elegantly.

Wei, G.H.↗

Development of the electron cooling simulation program for JLEIC

In the JLab Electron Ion Collider (JLEIC) project the traditional electron cooling technique is used to reduce the ion beam emittance at the booster ring, and to compensate the intrabeam scattering effect and maintain the ion beam emittance during collision at the collider ring. A new electron cooling process simulation program has been developed to fulfill the requirements of the JLEIC electron cooler design. The new program allows the users to calculate the electron cooling rate and simulate the cooling process with either DC or bunched electron beam to cool either coasting or bunched ion beam. It has been benchmarked with BETACOOL in aspect of accuracy and efficiency. In typical electron cooling process of JLEIC, the two programs agree very well and we have seen a significant improvement of computational speed using the new one. Being adaptive to the modern multicore hardware makes it possible to further enhance the efficiency for computationally intensive problems. The new program is being actively used in the electron cooling study and cooler design for JLEIC. We will present our models and some simulation results in this paper.

Zhang, He↗

Distinct water activation on polar/non-polar facets of ZnO nanoparticles

ZnO nanoparticles with differing dominant facets were prepared and characterized by a complimentary of techniques such as X-ray diffraction, electron microscopy, temperature programmed desorption of H2O, and Fourier transform infrared spectroscopy analysis of adsorbed D2O. For the first time, water interaction/activation is compared on ZnO polar and non-polar facets. We report that non-polar facets exhibit high activity in water activation, which favors reactions such as ketonization and steam reforming in which dissociated water is involved. The distinct water dissociation on ZnO non-polar facets could be related to its facile formation of oxygen vacancies under realistic reaction conditions.

Environmental Molecular Sciences Laboratory↗

The Differential Algebra Based Multiple Level Fast Multipole Algorithm for 3D Space Charge Field Calculation and Photoemission Simulation

Coulomb interaction between charged particles inside a bunch is one of the most importance collective effects in beam dynamics, becoming even more significant as the energy of the particle beam is lowered to accommodate analytical and low-Z material imaging purposes such as in the time resolved Ultrafast Electron Microscope (UEM) development currently underway at Michigan State University. In addition, space charge effects are the key limiting factor in the development of ultrafast atomic resolution electron imaging and diffraction technologies and are also correlated with an irreversible growth in rms beam emittance due to fluctuating components of the nonlinear electron dynamics. In the short pulse regime used in the UEM, space charge effects also lead to virtual cathode formation in which the negative charge of the electrons emitted at earlier times, combined with the attractive surface field, hinders further emission of particles and causes a degradation of the pulse properties. Space charge and virtual cathode effects and their remediation are core issues for the development of the next generation of high-brightness UEMs. Since the analytical models are only applicable for special cases, numerical simulations, in addition to experiments, are usually necessary to accurately understand the space charge effect. In this paper we will introduce a grid-free differential algebra based multiple level fast multipole algorithm, which calculates the 3D space charge field for n charged particles in arbitrary distribution with an efficiency of O(n), and the implementation of the algorithm to a simulation code for space charge dominated photoemission processes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of Cobalt Particle Size on Acetone Steam Reforming

Abstract Carbon‐supported cobalt nanoparticles with different particle sizes were synthesized and characterized by complementary characterization techniques such as X‐ray diffraction, N 2 sorption, acetone temperature‐programmed desorption, transmission electron microscopy, and CO chemisorption. Using acetone steam reforming reaction as a probe reaction, we revealed a volcano‐shape curve of the intrinsic activity (turnover frequency of acetone) and the CO 2 selectivity as a function of the cobalt particle size with the highest activity and selectivity observed at a particle size of approximately 12.8 nm. Our results indicate that the overall performance of acetone steam reforming is related to a combination of particle‐size‐dependent acetone decomposition, water dissociation, and the oxidation state of the cobalt nanoparticles.

Sun, Junming↗

Traceless Totally Symmetric Tensor Based Fast Multipole Method for Space Charge Field Calculation

The fast multipole method (FMM) is widely used to calculate the Coulomb interaction between a huge amount of charged particles. The efficiency of FMM scales with $O(N)$ for $N$ particles with any arbitrary distribution. Hence it is apposite for problems with complicated charge distribution or geometry. We developed a new FMM code for Coulomb interaction. In the new code the Coulomb potential is expressed as traceless totally symmetric tensors in Cartesian coordinates, in which the number of independent element is only $2n+1$ for the $n^{\mathrm{th}}$ rank, while it is $3^{n}$ for a general Cartesian tensor. The significant reduce of independent element number in Cartesian tensor helps to achieve high efficiency in the new algorithm. Result of test runs for space charge field calculation and multi-particle tracking using the new algorithm will be presented.

Zhang, He↗

ELECTRON COOLING STUDY FOR MEIC

Electron cooling of the ion beams is one critical R&D to achieve high luminosities in JLab?s MEIC proposal. In the present MEIC design, a multi-staged cooling scheme is adapted, which includes DC electron cooling in the booster ring and bunched beam electron cooling in the collider ring at both the injection energy and the collision energy. We explored the feasibility of using both magnetized and non-magnetized electron beam for cooling, and concluded that a magnetized electron beam is necessary. Electron cooling simulation results for the newly updated MEIC design is also presented.

43 PARTICLE ACCELERATORS↗

Fast Multipole Method for Coulomb Interaction Based on Traceless Totally Symmetric Tensor

The fast multipole method (FMM) is widely used to calculate the Coulomb interaction between a huge amount of charged particles. The efficiency of FMM scales with O(N) for N particles with any arbitrary distribution. Hence it is apposite for problems with complicated charge distribution or geometry. Under the same FMM framework, there are different approaches, such as using spherical harmonic functions or Maxwell Cartesian tensors. Here we will present a version using traceless totally symmetric Maxwell Cartesian tensor. The previous Maxwell Cartesian tensor based FMM uses totally symmetric tensor. There are (n+1)(n+2)/2 independent elements in a rank n totally symmetric tensor. However, there are only 2n+1 independent elements in a rank n traceless totally symmetric tensor, due to which the efficiency of the traceless version is highly improved compared with the old version, especially when high accuracy is needed and high rank tensors are used.

Huang, He↗

Medium Energy Electron Ion Collider at Jefferson Lab

At Jefferson Lab, the conceptual design of a next generation facility, the medium energy electron ion collider (MEIC), to reach the frontier in Quantum Chromodynamics has been carried on for years. The MEIC will provide an electron beam with energy up to 10 GeV, a proton beam with energy up to 100 GeV, and heavy ion beams with corresponding energy per nucleon with the same magnetic rigidity. The center-of-mass energy goes up to 70 GeV. Both the proton beam and the light-ion beams have high polarization above 70%. Two detectors, a primary one with full acceptance and a high-luminosity one with less demanding specification, are proposed. With the implementation of the traditional electron cooling in both the ion booster ring and the ion collider ring, particularly ultrahigh luminosity close to 1034 cm-2s-1 per detector with large acceptance can be achieved. We will present the recent progress in MEIC design.

Zhang, He↗

A GPU Accelerated Simulation Program for Electron Cooling Process

Electron cooling is essential to achieve high luminosity in the medium energy electron ion collider (MIEC) project at Jefferson Lab. Bunched electron beam with energy above 50 MeV is used to cool coasting and/or bunched ion beams. Although the conventional electron cooling technique has been widely used, such an implementation in MEIC is very challenging. We are developing a simulation program for the electron cooling process to fulfill the need of the electron cooling system design for MEIC. The program simulates the evolution of the ion beam under the intrabeam scattering (IBS) effect and the electron cooling effect using Monte Carlo method. To accelerate the calculation, the program is developed on a GPU platform. We will present some preliminary simulation results.

Zhang, He↗

Synergistic Catalysis between Pd and Fe in Gas Phase Hydrodeoxygenation of m-Cresol

In this work, a series of Pd/Fe2O3 catalysts were synthesized, characterized, and evaluated for the hydrodeoxygenation (HDO) of m-cresol. It was found that the addition of Pd remarkably promotes the catalytic activity of Fe while the product distributions resemble that of monometallic Fe catalyst, showing high selectivity towards the production of toluene (C-O cleavage without saturation of aromatic ring and C-C cleavage). Reduced catalysts featured with Pd patches on the top of reduced Fe nanoparticle surface, and the interaction between Pd and Fe was further confirmed using X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy (STEM) and X-ray absorption near edge fine structure (XANES). A possible mechanism, including Pd assisted H2 dissociation and Pd facilitated stabilization of metallic Fe surface as well as Pd enhanced product desorption, is proposed to be responsible for the high activity and HDO selectivity in Pd-Fe catalysts. The synergic catalysis derived from Pd-Fe interaction found in this work was proved to be applicable to other precious metal promoted Fe catalysts, providing a promising strategy for future design of highly active and selective HDO catalysts.

09 BIOMASS FUELS↗

Enhanced Fe2O3 Reducibility via Surface Modification with Pd: Characterizing the Synergy within Pd/Fe Catalysts for Hydrodeoxygenation Reactions

The synergistic catalysis in the hydrodeoxygenation of phenolic compounds over a Pd/Fe bimetallic surface has been well established. However, the nature of this synergy is still in part a mystery. In this work, we used a combined experimental and theoretical approach to understand a potential function of the surface Pd in the reduction of Pd/Fe2O3. This function of Pd was investigated via the comparison of the reduction properties as well as other physicochemical properties of samples synthesized by the reduction of Fe2O3 nanoparticles with and without surface Pd. Temperature-programmed reduction studies demonstrated the remarkable facilitation of reduction by addition of Pd, evidenced by a 150 degrees C shift toward lower temperature of the reduction peak of Fe3+. From X-ray photoelectron spectroscopy and theoretical calculation results, the interaction between Pd and the Fe2O3 surface occurs through the exchange of electrons with both the surface Fe and O atoms. This bonding between the Pd and surface oxide elements causes the Pd to partially donate electrons to the oxide surface, making the surface electrons more delocalized. This electron delocalization stabilizes the reduced oxide surfaces, as suggested by the TPR results and theoretical prediction. Therefore, the stabilization of the reduced Fe surface as well as the facilitated water formation by introduction of Pd is expected to significantly contribute to the Pd-Fe synergy in hydrodeoxygenation catalysis.

bimetallic catalysts↗

Assembly of three organic–inorganic hybrid supramolecular materials based on reduced molybdenum(V) phosphates

Three supramolecular materials based on (P{sub 4}Mo{sub 6}) polyoxoanions, (Hbbi){sub 2}(H{sub 2}bbi)[Cu{sub 3}Mo{sub 12}{sup V}O{sub 24}(OH){sub 6}(H{sub 2}O){sub 6}(HPO{sub 4}){sub 4}(H{sub 2}PO{sub 4}){sub 2}(PO{sub 4}){sub 2}]·3H{sub 2}O (1), (Hbbi){sub 2}(H{sub 2}bbi)[Ni{sub 3}Mo{sub 12}{sup V}O{sub 24}(OH){sub 6}(H{sub 2}O){sub 2}(HPO{sub 4}){sub 4}(H{sub 2}PO{sub 4}){sub 2}(PO{sub 4}){sub 2}]·9H{sub 2}O (2), (Hbpy)(bpy){sub 3}[Ni{sub 2}(H{sub 2}O){sub 10}Na(PCA){sub 2}][NiMo{sub 12}{sup V}O{sub 24}(OH){sub 6}(H{sub 2}PO{sub 4}){sub 6}(PO{sub 4}){sub 2}]·6H{sub 2}O (3) (bbi=1,1′-(1,4-butanediyl)bis(imidazole), bpy=4,4′-bipyridine, PCA=pyridine-4-carboxylic acid), have been hydrothermally synthesized and structurally characterized by the elemental analysis, TG, IR, UV–vis, PXRD and the single-crystal X-ray diffraction. Compounds 1 and 2 exhibit covalent 1-D chains constructed from M[P{sub 4}Mo{sub 6}]{sub 2} dimeric cluster and (M(H{sub 2}O){sub n}) (M=Cu, n=3 for 1 and M=Ni, n=1 for 2) linker. Compound 3 possesses an unusual POMMOF supramolecular layers based on [Ni(P{sub 4}Mo{sub 6})]{sub 2} dimeric units and 1-D metal–organic strings [Ni(H{sub 2}O){sub 5}Na(PCA)]{sub n}, in which an in situ ligand of PCA from 1,3-bis(4-pyridyl)propane (bpp) precursor was observed. Furthermore, the electrochemical behavior of 1–3-CPE and magnetic properties of 1–3 have been investigated in detail. - Graphical abstract: As new linking unit, Cu(H{sub 2}O){sub 3}, Ni(H{sub 2}O), and (Ni{sub 2}(H{sub 2}O){sub 10}Na(PCA){sub 2}) are introduced into (TM(P{sub 4}Mo{sub 6}){sub 2}) reaction systems to assemble three supramolecular materials under hydrothermal conditions via changing organic ligand and transition metal. - Highlights: • Tree new supramolecular hybrids based on (P{sub 4}Mo{sub 6}) cluster are reported. • Cu(H{sub 2}O){sub 3} and Ni(H{sub 2}O) as linker are introduced into the (TM(P{sub 4}Mo{sub 6}){sub 2}) systems. • 3 shows unusual layers based on [Ni(P{sub 4}Mo{sub 6})]{sub 2} and 1-D chains [Ni(H{sub 2}O){sub 5}Na(PCA)]{sub n}. • An in situ ligand of PCA from bpp precursor was observed in 3. • The electrochemical and magnetic properties of 1–3 have been studied in detail.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Supported metal catalysts for alcohol/sugar alcohol steam reforming

Despite extensive studies on hydrogen production via steam reforming of alcohols and sugar alcohols, catalysts typically suffer a variety of issues from poor hydrogen selectivity to rapid deactivation. Here, we summarize recent advances in fundamental understanding of functionality and structure of catalysts for alcohol/sugar alcohol steam reforming, and provide perspectives on further development required to design highly efficient steam reforming catalysts.

metal catalysts↗

Cavity morphology in a Ni based superalloy under heavy ion irradiation with cold pre-injected helium. I

In order to understand radiation damage in the nickel based superalloy Inconel X-750 in thermal reactors, where (n, α) transmutation reaction also occurred in addition to fast neutron induced atomic displacement, heavy ion (1 MeV Kr{sup 2+}) irradiation with pre-injected helium was performed under in-situ observations of an intermediate voltage electron microscope at Argonne National Laboratory. By comparing to our previous studies using 1 MeV Kr{sup 2+} irradiation solely, the pre-injected helium was found to be essential in cavity nucleation. Cavities started to be visible after Kr{sup 2+} irradiation to 2.7 dpa at ≥200 °C in samples containing 200 appm, 1000 appm, and 5000 appm helium, respectively, but not at lower temperatures. The cavity growth was observed during the continuous irradiation. Cavity formation appeared along with a reduced number density of stacking fault tetrahedra, vacancy type defects. With higher pre-injected helium amount, a higher density of smaller cavities was observed. This is considered to be the result of local trapping effect of helium which disperses vacancies. The average cavity size increases with increasing irradiation temperatures; the density reduced; and the distribution of cavities became heterogeneous at elevated temperatures. In contrast to previous characterization of in-reactor neutron irradiated Inconel X-750, no obvious cavity sink to grain boundaries and phase boundaries was found even at high doses and elevated temperatures. MC-type carbides were observed as strong sources for agglomeration of cavities due to their enhanced trapping strength of helium and vacancies.

36 MATERIALS SCIENCE↗

Cavity morphology in a Ni based superalloy under heavy ion irradiation with hot pre-injected helium. II

In the current investigation, TEM in-situ heavy ion (1 MeV Kr{sup 2+}) irradiation with helium pre-injected at elevated temperature (400 °C) was conducted to simulate in-reactor neutron irradiation induced damage in CANDU spacer material Inconel X-750, in an effort to understand the effects of helium on irradiation induced cavity microstructures. Three different quantities of helium, 400 appm, 1000 appm, and 5000 appm, were pre-injected directly into TEM foils at 400 °C. The samples containing helium were then irradiated in-situ with 1 MeV Kr{sup 2+} at 400 °C to a final dose of 5.4 dpa (displacement per atom). Cavities were formed from the helium injection solely and the cavity density and size increased with increasing helium dosage. In contrast to previous heavy ion irradiations with cold pre-injected helium, heterogeneous nucleation of cavities was observed. During the ensuing heavy ion irradiation, dynamical observation showed noticeable size increase in cavities which nucleated close to the grain boundaries. A “bubble-void” transformation was observed after Kr{sup 2+} irradiation to high dose (5.4 dpa) in samples containing 1000 appm and 5000 appm helium. Cavity distribution was found to be consistent with in-reactor neutron irradiation induced cavity microstructures. This implies that the distribution of helium is greatly dependent on the injection temperature, and helium pre-injection at high temperature is preferred for simulating the migration of the transmutation produced helium.

36 MATERIALS SCIENCE↗