Engineering topics
Publications and source records attributed to Yu, Jiaqi.
Single-atom metal embedded in nitrogen-doped carbon show high HER performance, with Co-NAC reaching 200 mA cm −2 at 310 mV overpotential.
Titanium dioxide (TiO 2 ) has long been employed as (photo)electrodes for reactions relevant to energy storage and renewable energy synthesis. Proton-coupled electron transfer (PCET) reactions with equimolar amounts of protons and electrons at the TiO 2 surface or within the bulk structure lie at the center of these reactions. Because a proton and an electron are thermochemically equivalent to an H-atom, these reactions are essentially H-atom transfer reactions. Thermodynamics of H-atom transfer has a complex dependence on the synthetic protocol and chemical history of the electrode, the reaction medium, and many others; together, these complications preclude the understanding of the H-atom transfer thermochemistry with atomic-level structural knowledge. Herein, we report our success in employing open-circuit potential (E OCP ) measurements to quantitatively determine the H-atom transfer thermochemistry at structurally well-defined Ti-oxo clusters within a colloidally stabilized metal–organic framework (MOFs), Ti-MIL-125. The free energy to transfer H-atom, Ti 3+ O–H bond dissociation free energy (BDFE), was measured to be 68(2) kcal mol -1 . To the best of our understanding, this is the first report on using E OCP measurements to quantify thermochemistry on any MOFs. The proton topology, the structural change upon the redox reaction, and BDFE values were further quantitatively corroborated using computational simulations. Furthermore, comparisons of the E OCP -derived BDFEs of Ti-MIL-125 to similar parameters in the literature suggest that E OCP should be the preferred method for quantitatively accurate BDFE calculations. Here, the reported success in employing E OCP for nanosized Ti- MIL-125 should lay the ground for thermochemical measurements of other colloidal systems, which are otherwise challenging. Implications of these measurements on Ti-MIL-125 as an H-atom acceptor in chemical reactions and comparisons with other MOFs/metal oxides are discussed.
Perovskite solar cells have seen impressive progress in performance and stability, yet maintaining efficiency while scaling area remains a challenge. Here we find that additives commonly used to passivate large-area perovskite films often co-precipitate during perovskite crystallization and aggregate at interfaces, contributing to defects and to spatial inhomogeneity. Here we develop design criteria for additives to prevent their evaporative precipitation and enable uniform passivation of defects. We explored liquid crystals with melting point below the perovskite processing temperature, functionalization for defect passivation and hydrophobicity to improve device stability. We find that thermotropic liquid crystals such as 3,4,5-trifluoro-4'-(trans-4-propylcyclohexyl)biphenyl enable large-area perovskite films that are uniform, low in defects and stable against environmental stress factors. We demonstrate modules with a certified stabilized efficiency of 21.1% at an aperture area of 31 cm 2 and enhanced stability under damp-heat conditions (ISOS-D-3, 85% relative humidity, 85 °C) with T 86 (the duration for the efficiency to decay to 86% of the initial value) of 1,200 h, and reverse bias with (ISOS-V-1, negative maximum-power-point voltage) and without bypass diodes.
Balancing kinetics, a crucial priority in catalysis, is frequently achieved by sacrificing activity of elementary steps to suppress side reactions and enhance catalyst stability. Dry reforming of methane (DRM), a process operated at high temperature, usually involves fast C-H activation but sluggish carbon removal, resulting in coke deposition and catalyst deactivation. Studies focused solely on catalyst innovation are insufficient in addressing coke formation efficiently. Herein, we develop coke-free catalysts that balance kinetics of elementary steps for overall thermodynamics optimization. Beginning from a highly active cobalt aluminum oxide (CoAl 2 O 4 ) catalyst that is susceptible to severe coke formation, we substitute aluminum (Al) with gallium (Ga), reporting a CoAl 0.5 Ga 1.5 O 4 -R catalyst that performs DRM stably over 1000 hours without observable coke deposition. We find that Ga enhances DRM stability by suppressing C-H activation to balance carbon removal. A series of coke-free DRM catalysts are developed herein by partially substituting Al from CoAl 2 O 4 with other metals.
Catalytic hydrogenolysis of polyolefins into valuable liquid, oil, or wax-like hydrocarbon chains for second-life applications is typically accompanied by the hydrogen-wasting co-formation of low value volatiles, notably methane, that increase greenhouse gas emissions. Catalytic sites confined at the bottom of mesoporous wells, under conditions in which the pore exerts the greatest influence over the mechanism, are capable of producing less gases than unconfined sites. A new architecture was designed to emphasize this pore effect, with the active platinum nanoparticles embedded between linear, hexagonal mesoporous silica and gyroidal cubic MCM-48 silica (mSiO 2 /Pt/MCM-48). This catalyst deconstructs polyolefins selectively into ~C 20 –C 40 paraffins and cleaves C–C bonds at a rate (TOF = 4.2 ± 0.3 s –1 ) exceeding that of materials lacking these combined features while generating negligible volatile side products including methane. The time-independent product distribution is consistent with a processive mechanism for polymer deconstruction. In contrast to time- and polymer length-dependent products obtained from non-porous catalysts, mSiO 2 /Pt/MCM-48 yields a C 28 -centered Gaussian distribution of waxy hydrocarbons from polyolefins of varying molecular weight, composition, and physical properties, including low-density polyethylene, isotactic polypropylene, ultrahigh-molecular-weight polyethylene, and mixtures of multiple, post-industrial polyolefins. Here, coarse-grained simulation reveals that the porous-core architecture enables the paraffins to diffuse away from the active platinum site, preventing secondary reactions that produce gases.
Boron monoxide (BO), prepared by the thermal condensation of tetrahydroxydiboron, was first reported in 1955; however, its structure could not be determined. With the recent attention on boron-based two-dimensional materials, such as borophene and hexagonal boron nitride, there is renewed interest in BO. A large number of stable BO structures have been computationally identified, but none are supported by experiments. The consensus is that the material likely forms a boroxine-based two-dimensional material. Herein, we apply advanced 11 B NMR experiments to determine the relative orientations of B(B)O 2 centers in BO. We find that the material is composed of D 2h -symmetric O 2 B–BO 2 units that organize to form larger B 4 O 2 rings. Further, powder diffraction experiments additionally reveal that these units organize to form two-dimensional layers with a random stacking pattern. This observation is in agreement with earlier density functional theory (DFT) studies that showed B 4 O 2 -based structures to be the most stable.
Explore the source record for details and available documents.
Solid-state nuclear magnetic resonance can be enhanced using unpaired electron spins with a method known as dynamic nuclear polarization (DNP). Fundamentally, DNP involves ensembles of thousands of spins, a scale that is difficult to match computationally. This scale prevents us from gaining a complete understanding of the spin dynamics and applying simulations to design sample formulations. We recently developed an ab initio model capable of calculating DNP enhancements in systems of up to ~1000 nuclei; however, this scale is insufficient to accurately simulate the dependence of DNP enhancements on radical concentration or magic angle spinning (MAS) frequency. We build on this work by using ab initio simulations to train a hybrid model that makes use of a rate matrix to treat nuclear spin diffusion. We show that this model can reproduce the MAS rate and concentration dependence of DNP enhancements and build-up time constants. Finally, we then apply it to predict the DNP enhancements in core–shell metal-organic-framework nanoparticles and reveal new insights into the composition of the particles’ shells.
Metallic nanocrystals (NCs) can be synthesized with tailored nonequilibrium shapes to enhance desired properties, e.g., octahedral fcc metal NCs optimize catalytic activity associated with {111} facets. However, maintenance of optimized properties requires stability against thermal reshaping. Thus, we analyze the reshaping of truncated fcc metal octahedra mediated by surface diffusion using a stochastic atomistic-level model with energetic input parameters for Pd. Furthermore, the model describes NC thermodynamics by an effective nearest-neighbor interaction and includes a realistic treatment of diffusive hopping for undercoordinated surface atoms. Kinetic Monte Carlo simulation reveals that the effective barrier, E eff , for the initial stage of reshaping is strongly tied to the degree of truncation of the vertices in the synthesized initial octahedral shapes. This feature is elucidated via exact analytic determination of the energy variation along the optimal reshaping pathway at low-temperature (T), which involves transfer of atoms from truncated {100} vertex facets to form new layers on {111} side facets. Deviations from predictions of the low-T analysis due to entropic effects are more prominent for higher T and larger NC sizes.