Engineering Papers⌕ Search

Engineering topics

Young, Larry A.

Publications and source records attributed to Young, Larry A..

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Vertical Lift Planetary Aerial Vehicles: Three Planetary Bodies and Four Conceptual Design Cases

NASA Ames Research Center has been studying the feasibility of vertical lift aerial vehicles to support planetary science and exploration missions. Besides Earth, it appears that there are three planetary bodies within our solar system where vertical flight might not only be theoretically feasible, but would also have unique mission capabilities that no other platform (ground-based, aerial, or orbital) could provide. Several vertical lift vehicle configurations might be applicable for planetary science missions. This paper presents a few representative conceptual design cases and the design challenges inherent in their development. Finally, more detailed comments are directed to the issues inherent in developing a NASA Mars Scout mission employing the use of a Martian autonomous rotorcraft.

Young, Larry A.↗
NASA NTRS2001

New Concepts and Perspectives on Micro-Rotorcraft and Small Autonomous Rotary-Wing Vehicles

A key part of the strategic vision for rotorcraft research as identified by senior technologists within the Army/NASA Rotorcraft Division at NASA Ames Research Center is the development and use of small autonomous rotorcraft. Small autonomous rotorcraft are defined for the purposes of this paper to be a class of vehicles that range in size from rotary-wing micro air vehicles (MAVs) to larger, more conventionally sized, rotorcraft uninhabited aerial vehicles (UAVs) - i.e. vehicle gross weights ranging from hundreds of grams to thousands of kilograms. The development of small autonomous rotorcraft represents both a technology challenge and a potential new vehicle class that will have substantial societal impact for: national security, personal transport, planetary science, and public service.

Young, Larry A.↗
NASA NTRS2000

Future Directions in Rotorcraft Technology at Ames Research Center

Members of the NASA and Army rotorcraft research community at Ames Research Center have developed a vision for 'Vertical Flight 2025'. This paper describes the development of that vision and the steps being taken to implement it. In an effort to realize the vision, consistent with both NASA and Army Aviation strategic plans, two specific technology development projects have been identified: (1) one focused on a personal transportation system capable of vertical flight (the 'Roto-Mobile') and (2) the other on small autonomous rotorcraft (which is inclusive of vehicles which range in grams of gross weight for 'MicroRotorcraft' to thousands of kilograms for rotorcraft uninhabited aerial vehicles). The paper provides a status report on these projects as well as a summary of other revolutionary research thrusts being planned and executed at Ames Research Center.

Aiken, Edwin W.↗
NASA NTRS2000

Vertical Lift: Not Just for Terrestrial Flight

Autonomous vertical lift vehicles hold considerable potential for supporting planetary science and exploration missions. This paper discusses several technical aspects of vertical lift planetary aerial vehicles in general, and specifically addresses technical challenges and work to date examining notional vertical lift vehicles for Mars, Titan, and Venus exploration.

Young, Larry A.↗
NASA NTRS1999

Overview of the Testing of a Small-Scale Proprotor

This paper presents an overview of results from the wind tunnel test of a 1/4-scale V-22 proprotor in the Duits-Nederlandse Windtunnel (DNW) in The Netherlands. The small-scale proprotor was tested on the isolated rotor configuration of the Tilt Rotor Aeroacoustic Model (TRAM). The test was conducted by a joint team from NASA Ames, NASA Langley, U.S. Army Aeroflightdynamics Directorate, and The Boeing Company. The objective of the test was to acquire a benchmark database for validating aeroacoustic analyses. Representative examples of airloads, acoustics, structural loads, and performance data are provided and discussed.

Young, Larry A.↗
NASA NTRS1999

Vortex Reconnection or Breakdown Subsequent to Perpendicular Collision With A Solid Body

This paper analytically examines the unsteady fluid dynamics of a vortex filament subsequent to a normal collision of the vortex with a solid body. In particular, the breakdown or reconnection phenomena, post-collision, for a vortex filament is studied. The paper does not investigate the collision dynamics process itself. The derived exact solution is based upon the laminar viscous form of the Helmholtz equations.

Young, Larry A.↗
NASA NTRS1999

Overview of the Testing of a Small-Scale Proprotor

This paper presents an overview of results from the wind tunnel test of a 1/4-scale V-22 proprotor in the Duits-Nederlandse Windtunnel (DNW) in The Netherlands. The small-scale proprotor was tested on the isolated rotor configuration of the Tilt Rotor Aeroacoustic Model (TRAM). The test was conducted by a joint team from NASA Ames, NASA Langley, U.S. Army Aeroflightdynamics Directorate, and The Boeing Company. The objective of the test was to acquire a benchmark database for validating aeroacoustic analyses. Representative examples of airloads, acoustics, structural loads, and performance data are provided and discussed.

Young, Larry A.↗
NASA NTRS1998

Technology Investigations With the Tilt Rotor Aeroacoustic Model (TRAM)

This paper introduces the Tilt Rotor Aeroacoustic Model (TRAM) project. The TRAM project is a key infrastructure investment for NASA tiltrotor research. The TRAM project consists of the development and testing of two modular, hardware-compatible, test stands: an isolated rotor configuration and a fullspan model (dual rotors with a complete airframe representation). These two test stands are inclusively called the Tilt Rotor Aeroacoustic Model (TRAM). The baseline proprotors and airframe of the TRAM test stands are nominally 1/4-scale representative of the V-22 Osprey aircraft. The research objectives of the project, the TRAM hardware design features and capabilities, illustrative examples of the type and quality of data that can be acquired with the TRAM, and the current status of the overall project will be discussed in this paper.

Young, Larry A.↗
NASA NTRS1997

Rotor Vortex Filaments: Living on the Slipstream's Edge

The purpose of this paper is to gain a better understanding of rotor wake evolution in hover and axial flow by deriving an analytical solution for the time dependent behavior of vortex filament circulation and core size. This solution is applicable only for vortex filaments in the rotor far-wake. A primarily inviscid vortex/shear layer interaction (where the slipstream boundary is modeled as a shear layer) has been identified in this analytical treatment. This vortex/shear layer interaction results in decreasing, vortex filament circulation and core size with time. The inviscid vortex/shear layer interaction is shown, in a first-order treatment, to be of greater magnitude than viscous diffusion effects. The rate of contraction, and ultimate collapse, of the vortex filament core is found to be directly proportional to the rotor inflow velocity. This new insight into vortex filament decay promises to help reconcile several disparate observations made in the literature and will, hopefully, promote new advances in theoretical modeling of rotor wakes.

Young, Larry A.↗
NASA NTRS1997

Vortex Core Size in the Rotor Near-Wake

Using a kinetic energy conservation approach, a number of simple analytic expressions are derived for estimating core size of tip vortices in the near-wake of rotors in hover or axial-flight (climb). The influence of thrust, axial-flight advance ratio, blade count, blade aspect ratio, nonuniform disk loading, and vortex structure on rotor vortex core size is assessed. Vortex core size is found to be directly proportional to rotor thrust and inversely proportional to axial-flight advance ratio. Further, it is found that the more efficient the rotor is with respect to factors that affect induced power, the smaller the vortex core size. In particular, uniformity of the rotor disk loading clearly has the greatest influence on vortex core size of the parameters studied in this paper.

Young, Larry A.↗
NASA NTRS1992

Aerodynamic Spring and Damping of Free-Pitching Tips on a Semispan Wing

A test was conducted in the NASA Ames 7- by 10-Foot Wind Tunnel to derive aerodynamic spring and damping estimates for free-pitching tips on a semispan wing. The test model was a rectangular planform semispan wing with wing tips that had a single rigid-body pitch degree of freedom with respect to the inboard wing. A number of different tip planform geometries were tested, incorporating a range of quarter-chord sweep angles and taper ratios. The wing-tip dynamic response characteristics were measured at several wing angles of attack and tunnel dynamic pressures. The tip oscillations were initiated by releasing the tips from prescribed angles of attack. A new method to isolate Coulomb damping from aerodynamic damping from these tip-motion time histories is developed and applied. Correlations were performed between the experimentally derived wing-tip aerodynamic spring and damping values and predictions from a semiempirical analysis based on steady-state tip aerodynamic loads.

Young, Larry A.↗
NASA NTRS1990

Improved Hub Fairings For Helicopters

Wind-tunnel experiments show new generic configuration for fairing for helicopter rotor hub reduces contribution of hub to overall aerodynamic drag. New generic fairing has flat bottom, which eliminates converging/diverging boundary by straightening surfaces facing each other. Reduces interference drag, similarly to reduction of interference drag by flattening of facing surfaces of two side-by-side airfoils.

Stroub, Robert H.↗
NASA NTRS1987

Investigation of generic hub fairing and pylon shapes to reduce hub drag

Reported are investigations of fairing configurations pointed toward substantially reducing hub drag. Experimental investigations have shown the importance of hub-fairing camber, lower-surface curvature, and relative size of the drag. The significance of pylon and hub fairings in combination have also been shown. Model test data presented here documented these findings, and also showed the effect of gaps and hub-fairing inclination angle on drag. From a drag standpoint, the best hub fairing had a circular arc, upper-surface curvature, a flat bottom surface, and 8.75% camber.

Stroub, Robert H.↗
NASA NTRS1987

Investigation of generic hub fairing and pylon shapes to reduce hub drag

This paper reports investigations of fairing configurations pointed toward substantially reducing hub drag. Experimental investigations have shown the importance of hub-fairing camber,lower-surface curvature, and relative size on the drag. The significance of pylon and hub fairings in combination have also been shown. Model test data presented here documented these findings, and also showed the effect of gaps and hub-fairing inclination angle on drag. From a drag standpoint, the best hub fairing had a circular arc, upper-surface curvature, a flat bottom surface, and 8.75 percent camber.

Stroub, Robert H.↗
NASA NTRS1987

Performance and loads data from a hover test of a 0.658-scale V-22 rotor and wing

A hover test of a 0.658-scale model of a V-22 rotor and wing was conducted at the Outdoor Aerodynamic Research Facility at Ames Research Center. The primary objectives of the test were to obtain accurate measurements of the hover performance of the rotor system, and to measure the aerodynamic interactions between the rotor and wing. Data were acquired for rotor tip Mach numbers ranging from 0.1 to 0.73. This report presents data on rotor performance, rotor-wake downwash velocities, rotor system loads, wing forces and moments, and wing surface pressures.

Felker, Fort F.↗
NASA NTRS1987

Reduction of hub- and pylon-fairing drag

A wind tunnel test was conducted to obtain data on several drag reduction methods for rotorcraft hubs. The objective of the test was to use small-scale models to develop the technology to substantially reduce hub drag. A helicopter test model, which did not incorporate a rotor, was used to study single-rotor fairing configurations. The rotor shaft assembly was modeled with nonrotating hardware. Drag trend data was obtained for the following fairing configuration changes: hub-fairing camber, hub-fairing thickness ratio, hub-fairing surface curvature, hub-fairing height with respect to the fuselage, inclusion of blade shanks in the hub fairings, hub- and pylon-fairing gaps, pylon-fairing cross-sectional geometry, pylon-fairing thickness ratio and camber. Substantial drag reductions could potentially result from application of the test results to helicopter hub- and pylon-fairing design.

Young, Larry A.↗
NASA NTRS1986

Performance and loads data from a hover test of a full-scale advanced technology XV-15 rotor

A hover test of a full-scale, composite, advanced technology XV-15 rotor was conducted at the Outdoor Aerodynamic Research Facility at Ames Research Center. The primary objective of the test was to obtain accurate measurements of the hover performance of this rotor system. Data were acquired for rotor tip Mach numbers ranging from 0.35 to 0.73. The rotor was tested with several alternate blade root and blade-tip configurations. Data are presented on rotor performance, rotor-wake downwash velocities, and rotor system loads.

Felker, Fort F.↗