Optimization of nonatitanate electrodes for sodium-ion batteries
Explore the source record for details and available documents.
99 GENERAL AND MISCELLANEOUS↗
Engineering topics
Yi, Eongyu
Publications and source records attributed to Yi, Eongyu.
Optimization of Tape Casting for Fabrication of Li 6.25 Al 0.25 La 3 Zr 2 O 12 Sheets
Tape casting is an attractive technology for the scalable manufacturing of thin lithium garnet electrolyte (LLZO) layers for solid state battery applications. Processing of LLZO is complicated by many factors including lithium volatilization, abnormal grain growth, and phase instability, which are exacerbated by high surface area to volume ratios. In this work a sintering protocol for commercially available Li 6.25 Al 0.25 La 3 Zr 2 O 12 Sheets (Al-LLZO) powder was developed that requires no mother-powder covering or externally applied pressure. MgO was investigated as a sintering additive to improve density and ionic conductivity of the Al-LLZO sheets and produce a fine-grained microstructure. Al-LLZO sheets with 5 wt % MgO had densities of > 90% and ionic conductivity > 2 × 10 -4 S/cm. The optimized ceramic composition and sintering protocol were used to compare several tape casting binder systems. A "green"water-based system using methylcellulose as a binder was developed with green and final properties comparable to those obtained with solvent-based systems.
25 ENERGY STORAGE↗
(Invited) All-Solid-State Batteries Using Li 7 La 3 Zr 2 O 12 Garnet Electrolyte Framework
All-solid-state batteries (ASSB) using LLZO (variants of Li 7 La 3 Zr 2 O 12 ) garnet solid electrolyte with lithium metal anode potentially offer higher energy density and improved safety. Rational design of cell architecture as well as manufacturing scalability are key aspects to consider as the technology readiness level advances. A thick composite cathode layer attached to a thin solid electrolyte layer is desirable to obtain superior energy densities. Furthermore, the architecture within the composite cathode may be engineered to contain directional conduction paths of lithium ions or electrons for enhanced rate capabilities. Here, we demonstrate a functioning bulk-type LLZO based all-solid-state battery with a practical form factor incorporating the above described design concepts. Freeze-tape-casting (FTC), a scalable and environmentally friendly ceramic processing method, is used to construct 3D porous LLZO scaffolds composed of vertical arrays of LLZO walls. The thin solid-electrolyte layer is fabricated by tape-casting (TC). By sintering the stacks of FTC and TC green tapes, porous/dense bilayers and porous/dense/porous trilayers of LLZO frameworks are obtained. An ASSB was constructed using a porous/dense bilayer by infiltrating LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode powder and carbon black into the porous layer and adhering lithium metal foil to the dense side. We find it crucial to introduce a plastic crystal based soft solid electrolyte to the porous layer to electrochemically connect all cathode components, obviating the need for co-sintering to establish contact. The soft nature of the plastic crystal based solid-electrolyte may be able to accommodate the volume change of the cathode material as it cycles. In this device, which contained no liquid component, the initial discharge capacities were similar to those observed in a lithium ion battery configuration using the same cathode powder at C/10 rates.
25 ENERGY STORAGE↗
Processing combustion synthesized Mg0.5Zr2(PO4)3 nanopowders to thin films as potential solid electrolytes
Not Available
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Enabling fast charging of lithium-ion batteries through secondary- /dual- pore network: Part I - Analytical diffusion model
Battery performance is strongly correlated with electrode microstructural properties. Enabling fast charging of lithium-ion batteries requires improved through-plane ionic diffusion that can be achieved through, among other strategies, structured electrodes with a secondary- or dual-pore network (SPN). In this work, an analytical model investigates the impact of such an SPN on ionic diffusion with a composite electrode, considering various pore-channel geometries and comparing to standard electrodes with identical gravimetric- and volumetric-specific theoretical capacities. Relevant SPN design parameters and tortuosity coefficients are identified according to three optimization objectives that aim to balance the improved overall through-plane diffusion, thanks to the coarse aligned channels, and degraded in-plane diffusion because of the porous matrix densification required to maintain gravimetric- and volumetric-specific theoretical capacities. The model indicates that a relatively low amount of SPN is required and that electrodes with high through-plane tortuosity and low in-plane tortuosity benefit most from such architecture.
25 ENERGY STORAGE↗
Scalable Freeze-Tape-Casting Fabrication and Pore Structure Analysis of 3D LLZO Solid-State Electrolytes
Nonflammable solid-state electrolytes can potentially address the reliability and energy density limitations of lithium-ion batteries. Garnet-structured oxides such as Li 7 La 3 Zr 2 O 12 (LLZO) are some of the most promising candidates for solid-state devices. Here, three-dimensional (3D) solid-state LLZO frameworks with low tortuosity pore channels are proposed as scaffolds, into which active materials and other components can be infiltrated to make composite electrodes for solid-state batteries. To make the scaffolds, we employed aqueous freeze tape casting (FTC), a scalable and environmentally friendly method to produce porous LLZO structures. Using synchrotron radiation hard X-ray microcomputed tomography, we confirmed that LLZO films with porosities of up to 75% were successfully fabricated from slurries with a relatively wide concentration range. The acicular pore size and shape at different depths of scaffolds were quantified by fitting the pore shapes with ellipses, determining the long and short axes and their ratios, and investigating the equivalent diameter distribution. The results show that relatively homogeneous pore sizes and shapes were sustained over a long range along the thickness of the scaffold. Additionally, these pores had low tortuosity and the wall thickness distributions were found to be highly homogeneous. These are desirable characteristics for 3D solid electrolytes for composite electrodes, in terms of both the ease of active material infiltration and also minimization of Li diffusion distances in electrodes. The advantages of the FTC scaffolds are demonstrated by the improved conductivity of LLZO scaffolds infiltrated with poly(ethylene oxide)/lithium bis(trifluoromethanesulfonyl)imide (PEO/LITFSI) compared to those of PEO/LiTFSI films alone or composites containing LLZO particles.
36 MATERIALS SCIENCE↗
All-Solid-State Batteries Using Rationally Designed Garnet Electrolyte Frameworks
Functioning bulk-type all-solid-state batteries in a practical form factor with composite positive electrodes, using Al-substituted Li 7 La 3 Zr 2 O 12 (LLZO) as the solid electrolyte, have been demonstrated for the first time. The devices incorporate bilayers composed of dense LLZO membranes and porous LLZO scaffolds infiltrated with LiNi 0.6 Mn 0.2 Co 0.2 O 2 and other components as positive electrodes, combined with lithium anodes. The porous scaffolds are prepared using an easily scaled freeze-tape-casting method. The unidirectional pores of the scaffold facilitate infiltration of cathode components and shorten lithium ion diffusion path lengths, while the addition of a soft ionically conductive solid to the scaffold ensures good contact among the components.
25 ENERGY STORAGE↗