Solid-State Battery Cathode Modeling in SABERS
Explore the source record for details and available documents.
Li-S battery↗
Engineering topics
Yi Lin
Publications and source records attributed to Yi Lin.
Characterizing the Structure of Lithium Metal Batteries using Local Ultrasonic Resonance Spectroscopy (LURS)
Safe use of high energy density batteries is critical for electrifying aerospace and other transportation sectors. Nondestructive evaluation (NDE) techniques are being developed for characterizing battery structures throughout their lifetimes so that damage mechanisms can be better understood, and prognostic tools can be developed. In this study Local Ultrasonic Resonance Spectroscopy (LURS) is applied to lithium metal pouch cell batteries of a variety of form-factors that are brought from fabrication to end of life under different charge rates, temperatures, and loading scenarios. LURS data shows improved sensitivity to changes in structure in comparison to amplitude-based methods, allowing differences in damage development to be identified as well as giving opportunities for quality control in manufacturing.
Ultrasound↗
Characterizing the Structure of Lithium Metal Batteries using Local Ultrasonic Resonance Spectroscopy (LURS)
Safe use of high energy density batteries is critical for electrifying aerospace and other transportation sectors. Nondestructive evaluation (NDE) techniques are being developed for characterizing battery structures throughout their lifetimes so that damage mechanisms can be better understood, and prognostic tools can be developed. In this study Local Ultrasonic Resonance Spectroscopy (LURS) is applied to lithium metal pouch cell batteries of a variety of form-factors that are brought from fabrication to end of life under different charge rates, temperatures, and loading scenarios. LURS data shows improved sensitivity to changes in structure in comparison to amplitude-based methods, allowing differences in damage development to be identified as well as giving opportunities for quality control in manufacturing.
Matthew Webster↗
Solid-State Architecture Batteries for Enhanced Rechargeability and Safety (SABERS): Advanced Battery Technology for Sustainable Aviation
All-electric vertical take-off and landing vehicles (eVTOL) for urban air mobility (UAM) concepts face numerous challenging technical barriers before their introduction into the consumer marketplace. The primary barrier to overcome is developing an energy storage system capable of meeting the rigorous aerospace safety and performance criteria. The performance metrics for eVTOL vehicles are at least two times greater than those of electric ground vehicles. Furthermore, inherently non-flammable batteries are essential for safe operation of commercial electric aerovehicles. The SABERS concept proposes a battery that meets the key performance criteria through development of a solid-state architecture battery utilizing high-capacity sulfur-selenium cathode and lithium metal anode. The combination of sulfur and selenium offers a balanced energy-to-power density ratio, which can be tailored to the specific application by altering the stoichiometric ratios of sulfur to selenium. This hybrid cathode will be developed by implementing NASA patented holey graphene technology as a highly conductive, ultra-lightweight electrode scaffold. A solid-state electrolyte will be used as a safe, non-flammable replacement to the highly flammable liquid organic electrolytes currently used in SOA lithium-ion batteries. This solid-state lithium-sulfur/selenium cell will be designed into a serial stacking configuration to enable dense packaging of the battery cells. The serial stacking configuration is termed a bipolar stack, which has the advantages of reducing overall cell weight, simplifying the interfaced connections for the cell, and minimizing the cooling requirements. Lastly, optimization of battery components will occur through a robust and rigorous combination of various computational modeling techniques covering multiple length scales. The expected result will be a fully solid-state battery with operational temperatures up to 150 °C which provides the required energy density, discharge rates, and inherent safety to meet the strict aerospace mission performance criteria. This presentation will demonstrate a feasible path for solid-state cells that possess a specific energy of greater than 400 Wh/kg to enable electric aircraft. The presentation will also explore novel materials and computational models used to achieve all solid-state cells that operate safely at very high temperatures and specific energies. The cells can withstand damage while operating without an increase in temperature or spontaneous ignition.
Urban Air Mobility (UAM) Vehicles↗
Latent Cure Epoxy Resins for Reliable Joints in Secondary-Bonded Composite Structures
In high-performance polymer matrix composite assemblies, adhesive bonding is generally superior to mechanical fastening in structural performance and manufacturing efficiency. However, adhesive bonds are susceptible to minute levels of contamination accumulated during assembly that can lead to unpredictable, weak bonds. Current methods of measuring bond strength are all destructive mechanical tests. To overcome these challenges, redundant load paths (e.g., mechanical fasteners) are often implemented in secondary-bonded, primary-structures, which can greatly reduce structural performance. This study investigated reformulated aerospace epoxy matrix resins with stoichiometric offset to inhibit cure of the matrix resin prior to assembly. Inhibited resins can reflow and mix across the joint interface, which eliminates the material discontinuity and forms a homogenous joint with reliable fracture properties. The goal of this study was to develop and demonstrate secondary composite assemblies that are mechanically and microscopically indistinguishable from a co-cured composite joint. This article describes the development of latent epoxy resins, the fabrication of test articles, and the mechanical properties measured from experimental joints compared with conventional, co-cured laminates. Methods of in-line quality control using and infrared spectroscopy and post-assembly forensics are also described. The final mode-II fracture toughness measured from precracked AERoBOND specimens was similar to that measured from co-cured laminates indicating that later cure epoxy materials could be a suitable replacement for secondary bonding.
Polymer-matrix composites (PMCs)↗
Machine Learning to Predict Joint Performance in Epoxy Composites Based on Process Parameters
Polymer matrix composites are gaining popularity in the aerospace industry due to their high specific strength, fatigue properties, and processability. However, based on current FAA certification guidelines, manufacturers utilizing current state-of-the-art composites made with adhesive bonds commonly install redundant fasteners to guarantee the strength of these adhesively bonded composite parts. The number of fasteners in a single-aisle commercial transport aircraft is typically on the order of 105, which reduces manufacturing rate, increases cost tremendously, and reduces the advantage of the specific strength composites provide. Due to this, the Adhesive Free Bonding of Composites (AERoBOND) project at NASA Langley Research Center has developed a novel assembly process to manufacture complex composite parts without the use of adhesives and fasteners. However, optimization of the process is currently challenging due to the complex and interdependent process parameters. To assist with the optimization, four machine learning algorithms utilizing gradient boosting decision trees were created to provide predictions for the mechanical and characterization properties of the composite parts. Approximately 200 random states from each algorithm were tested, and the models from each state were isolated and analyzed based on their accuracy, a validation process, and their feature importance. This analysis concluded that the models created from the machine learning algorithms could accelerate a parametric study for the AERoBOND process by rapidly optimizing process parameters to achieve desired performance characteristics.
Brennen Michael Middleton↗
Solid-state Architecture Batteries for Enhanced Rechargeability and Safety (SABERS)
All-electric vertical take-off and landing vehicles (eVTOL) for urban air mobility (UAM) concepts face numerous challenging technical barriers before their introduction into the consumer marketplace. The most challenging of these technical barriers to overcome is developing an energy storage system capable of meeting the rigorous aerospace safety and performance criteria. The performance metrics for eVTOL craft, such as specific energy and cycle life, are at least 2 times greater than those of electric automobiles. Furthermore, safety is essential for operation of commercial electric aerovehicles. Preliminary systems level analysis studies have indicated that there are five key properties which must be optimized for successful implementation of battery systems. Those five key criteria are safety, energy density, power, packaging design and scalability. Current state-of-the-art (SOA) lithium-ion batteries meet or exceed the requirements for electric aviation in the areas of power and scalability, yet are insufficient in the key performance criteria of energy, safety and packaging design. The SABERS concept proposes a battery that meets all five key performance criteria through the development of a solid-state architecture cell design utilizing high energy density and power density sulfur-selenium cathode with a lithium metal anode. Data will be presented demonstrating high performing sulfur - selenium cathode that offers a balanced energy to power density ratio, which can be tailored to the specific application by altering the stoichiometric ratios of sulfur to selenium. This cathode is being developed by implementing NASA patented holey graphene technology as a highly conductive, ultra-lightweight electrode scaffold. Novel processing methods allow developing solid-state electrolyte that is a safe, non-flammable replacement to the highly flammable liquid organic electrolytes currently used in SOA lithium-ion batteries. The all solid-state lithium-sulfur-selenium cell design enables the implementation of a bipolar stack configuration, which has the advantages of reducing overall cell weight, reducing the amount of interfaced connections for the cell, and minimizing cooling requirements for the battery. In particular, the solid-state design allows for a serial stacking configuration to enable dense packaging of the cells within the bipolar stack. Lastly, optimization of battery components occurs through a robust and rigorous combination of various computational modeling techniques covering multiple length scales. The expected result will be a solid-state battery with operational temperatures from 0 °C to 150 °C which provides the required energy density, discharge rate, and inherent safety to meet strict aerospace performance criteria.
solid state batteries↗
Lightweight Regenerable CO2-to-Power Conversion (RECOP) System for Safer Manned Missions
Explore the source record for details and available documents.
Lithium-CO2 batteries↗
Reduced Dependence on Redundant Fasteners in Secondary-Bonded Composite Structures Using Modified Epoxy Matrix Resins
This report describes a sub-set of over 20 experiments conducted to optimize materials and processes to maximize mechanical properties of the assembled joint. Infrared (IR) spectroscopy was used to measure the chemical state of the ER surface after primary cure. Laminates were fabricated with various HR and ER layer thicknesses, inspected using ultrasonic testing, and mechanically tested to measure fracture toughness.
Frank L Palmieri↗
An Ultra-long Life, High-performance, Flexible Li-CO2Battery Based on Multifunctional Carbon Electrocatalysts
Integrating CO2 utilization and renewable energy delivery/storage, the rechargeable Li–CO2 battery has been considered as a promising candidate for next-generation secondary batteries. However, high-performance catalyst(s) for efficient formation and decomposition of the discharge product, Li2CO3, are an imperative part of a Li–CO2 battery. The development of flexible Li–CO2 batteries extends their applications into compliant and wearable devices/systems, but at the same time imposes a big challenge for battery fabrication and lifetime enhancement. In this study, a rechargeable quasi-solidus flexible Li–CO2 battery was designed and fabricated using highly active N,S-doped carbon nanotubes (N,S-doped CNTs) as the cathode catalyst, and a smart polymer gel as the flexible electrolyte. This newly-developed flexible Li–CO2 battery exhibited a capacity as high as 23560 mAh g−1 based on the catalyst mass and an ultra-long lifetime of up to 538 cycles with excellent mechanical flexibility. This work provides a platform for the design and development of high-performance flexible Li–CO2 batteries from low-cost, earth-abundant, carbon-based multifunctional cathode catalysts.
Superior stability↗
Nanomanufacturing of Graphene Nanosheets Through Hole Engineering
Facile and scalable fabrication of highly dense and high quality graphene films and articles is extremely attractive for a range of electronic and mechanical applications. Pristine, high quality graphene with its inherent impermeability poses challenges in fabricating dense films and thick parts with high electrical conductivity due to the difficulty in removing trapped air and/or solvents used in various fabrication methods. To overcome this deficiency, nano-holes were intentionally created in pristine graphene (“holey graphene”) with an average diameter of approximately 15 nm. The holes serve as pathways for the rapid removal of gases or liquids and enable the fabrication of dense holey graphene nanostructures. Subsequently, a high temperature process is applied to effectively repair the nano-holes and recover the high quality graphene conjugated network. Through the creation and repair of the nano-holes, dense graphene articles were created that exhibited an ultrahigh conductivity of 2209 S/cm and a high carrier mobility of 673 cm2V-1s-1. This unique processing methodology enables the facile and scalable fabrication of high quality graphene constructs for a variety of applications.
Yanan Chen↗
Solvent-Free Preparation of High Energy, Binder-Free Electrodes Enabled by Dry Compressible Holey Graphene
Graphene is an atomically thick sheet consisting of a graphitic carbon network with excellent mechanical strength, electrical and thermal conductivity, and chemical stability. Holey graphene, a structural derivative of graphene, has an array of through-the-thickness holes across the lateral surface of the nanosheet. The presence of these holes has minimal detrimental effect on the graphene properties and leads to enhanced performance in applications such as electronics, sensors, and energy storage. For example, these holes allow more facile cross-plane ion and gas transport than intact graphene, making holey graphene an ideal electrode material for electrochemical energy storage. This presentation will focus on the ability of holey graphene to be compression molded into robust articles or architectures under solvent-free conditions without the need for potentially parasitic binders. The unique dry compressibility of holey graphene has enabled facile fabrication of high mass loading electrodes with both high density and high porosity, which have found use in supercapacitors and various high-energy battery systems such as lithium-oxygen, lithium-sulfur, and lithium-selenium batteries.
Yi Lin↗
TPSAS-NF1676L-35028-DND
Explore the source record for details and available documents.
Christian O Plaza-Rivera↗
Ultrahigh Mass Loading Batteries with Holey Graphene-Enabled Dry-Pressed Cathode Architectures
Holey graphene is a structural derivative of graphene with arrays of nanometer-sized, through-thickness holes across the lateral surface of the atomically thin nanosheet. It has been widely acknowledged that the presence of holes improves ion transport through the graphene planes, making holey graphene an ideal electrode material for electrochemical energy storage. We recently discovered another unique attribute of holey graphene in that it can be directly compressed from powder into electrode in a single step without the use of solvent or binder. In addition to neat holey graphene electrodes, composite electrodes with holey graphene as an ultralightweight scaffold host filled with various active materials can also be readily prepared in a similar solvent-free and binder-free fashion. The active materials can be metal-containing catalysts for lithium-oxygen batteries, lithium-ion battery electrode materials, or high energy density components such as sulfur. Compared to the conventional slurry-based process, the dry-press method is comparably much more suitable toward the facile and scalable preparation of ultrahigh mass loading electrodes with ultrahigh areal capacities.
holey graphene, cathode scaffold, lithium metal, h↗
Layered Electrode Architectures Enabled by Holey Graphene Hosts
Battery electrodes are typically prepared using a slurry-based method, where high boiling point organic solvents are typically used with a polymer binder to disperse active electrode materials and conductive carbon additives followed by casting into current collector sheets. In this process, the use of organic solvents are environmentally hazardous, energy intensive, and time-consuming, while polymeric binders add weight and can undergo parasitic reactions during battery cycling. Here we discuss the use of a unique conductive carbon nanomaterial, namely holey graphene, as a multifunctional host that can be processed via a facile, solvent-free, binder-free, cold pressing method to prepare electrodes with unique architectures. This approach can accommodate a broad range of battery chemistries, such as lithium oxygen/carbon dioxide (Li-O2/CO2), lithium sulfur/selenium (Li-S/Se), and various lithium ion chemistries. The successful use of dry, cold compression allows the convenient modification of electrode mass loading with unique architectures containing active materials randomly mixed or layered with single or multiple layers of one or more active materials. In the conventional slurry-based electrode fabrication method, it is difficult, if not impossible, to achieve such layered architectures. In particular, the layered electrode architectures from the dry, cold press approach are easy to fabricate without significantly sacrificing device performance, and are amenable to continuous roll-to-roll dry processing. In addition, these architectures offer unprecedented perspectives on the battery material loading vs. utilization efficiency, as well as enabling unique characterization opportunities to advance mechanistic understanding of various battery chemistries. Potential applications of this unique electrode fabrication approach for solid-state batteries will also be discussed.
holey graphene, batteries, electrode architecture,↗
Modified Epoxy Matrix Resins for Reduced Dependence on Redundant Fasteners in Secondary-Bonded Composite Structures
In structural bonds, the interface between adherend and adhesive is nearly two-dimensional making it susceptible to minute quantities of contamination that can lead to weak bonds. No methods currently exist to measure the strength of an adhesive bond nondestructively. For these reasons, regulating organizations such as the Federal Aviation Administration (FAA) often require redundant load paths in secondary-bonded, primary-structures to achieve certification for civil transport aircraft. To meet this requirement, manufacturers commonly install redundant fasteners (~105 fasteners in a twin-aisle airframe with composite fuselage and wings), which add tremendous complexity, time and cost, and significantly reduce performance of the airframe. Under NASA’s Convergent Aeronautics Solutions (CAS) Program, the Adhesive Free Bonding of Composites (AERoBOND) project is investigating reformulated aerospace epoxy matrix resins to enable reflow and diffusion of the resin at the interface during a secondary bonding/cure process. The mixing process eliminates the material discontinuity at the interface, thereby removing the dependence of bond performance on adhesion across a nearly two-dimensional boundary. The AERoBOND interface is similar to the interlaminar region formed during a co-cure process, so joint performance depends on the cohesive properties of the matrix resin, which can be measured, inspected non-destructively, and certified for flight with fewer redundant fasteners. This presentation describes the ongoing development of stoichiometrically-offset epoxy resins to control the degree of cure in composite joints and enable interfacial mixing during secondary bonding/curing. Details on the resin formulation, laminate fabrication, and mechanical testing will also be presented. The precracked mode-II fracture toughness measured from preliminary AERoBOND joints was similar for joints fabricated with conventional epoxy matrix materials.
thermoset, hardener, prepreg, assembly↗
Effect of Holey Graphene Chemistry on Li – S/Se Battery Cathode Performance
Explore the source record for details and available documents.
lithium-sulfur batteries, holey graphene, high mas↗