Engineering Papers⌕ Search

Engineering topics

Ye, Yusheng

Publications and source records attributed to Ye, Yusheng.

17 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Deconvoluting Effects of Lithium Morphology and SEI Stability at Moderate Current Density Using Interface Engineering

Lithium (Li)-morphology and solid electrolyte interphase (SEI) are among the most significant performance regulators in Li-metal batteries (LMBs). While both Li-morphology and SEI composition play key roles in the cyclability of LMBs, less is understood about the individual contributions of each factor to overall Li reversibility, particularly at a practical current density (1 mA cm −2 ) at which the kinetics of both factors are not naturally separated. Herein, an interface engineering approach is introduced to deconvolute the impacts of Li-morphology and SEI composition on battery performance. By using interfacial nanofilms with differing resistivity (resistive HfO 2 versus conductive ZnO), the morphology of Li is varied, and by virtue of similar acidic character of the nanofilms, the formation of anion-rich SEIs is maintained. It is established that although the surface acidity of the thin films enables preformation of a more anion-rich SEI, it is not preserved after Li plating. It is further shown that resistance-controlled, low-surface-area Li-morphology exhibits up to threefold increase in stable cycle life when tested in multiple electrolytes. Overall, these findings explain why Li-morphological control is more advantageous for performance improvement than preformed SEI modulation due to the inherent challenges in SEI preservation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Electrified Operando -Freezing of Electrocatalytic CO 2 Reduction Cells for Cryogenic Electron Microscopy

The ability to freeze and stabilize reaction intermediates in their metastable states and obtain their structural and chemical information with high spatial resolution would be very powerful to unravel the fundamentals in many important materials technologies such as catalysis and batteries. Here, we develop an electrified operando-freezing methodology for the first time to preserve these metastable states under electrochemical reaction conditions for cryogenic electron microscopy (cryo-EM) imaging and spectroscopy. Using Cu catalysts for CO 2 reduction as a model system, we observe restructuring of the Cu catalyst in a CO 2 atmosphere while the same catalyst remains intact in an air atmosphere at the nanometer scale. Furthermore, we discover the existence of single valance Cu (1+) state and C-O bonding at the electrified liquid-solid interface of the operando-frozen samples, which are key reaction intermediates that traditional ex situ measurements fail to detect. Finally, this work highlights our novel technique to study the local structure and chemistry of electrified liquid-solid interfaces, which has broad impact for many electrochemical reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Interlayer engineering of Fe 3 GeTe 2 : From 3D superlattice to 2D monolayer

The discoveries of ferromagnetism down to the atomically thin limit in van der Waals (vdW) crystals by mechanical exfoliation have enriched the family of magnetic thin films [C. Gong et al., Nature 546 , 265–269 (2017) and B. Huang et al., Nature 546 , 270–273 (2017)]. However, compared to the study of traditional magnetic thin films by physical deposition methods, the toolbox of the vdW crystals based on mechanical exfoliation and transfer suffers from low yield and ambient corrosion problem and now is facing new challenges to study magnetism. For example, the formation of magnetic superlattice is difficult in vdW crystals, which limits the study of the interlayer interaction in vdW crystals [M. Gibertini, M. Koperski, A. F. Morpurgo, K. S. Novoselov, Nat. Nanotechnol. 14 , 408–419 (2019)]. Here, we report a strategy of interlayer engineering of the magnetic vdW crystal Fe 3 GeTe 2 (FGT) by intercalating quaternary ammonium cations into the vdW spacing. Both three-dimensional (3D) vdW superlattice and two-dimensional (2D) vdW monolayer can be formed by using this method based on the amount of intercalant. On the one hand, the FGT superlattice shows a strong 3D critical behavior with a decreased coercivity and increased domain wall size, attributed to the co-engineering of the anisotropy, exchange interaction, and electron doping by intercalation. On the other hand, the 2D vdW few layers obtained by over-intercalation are capped with organic molecules from the bulk crystal, which not only enhances the ferromagnetic transition temperature ( T C ), but also substantially protects the thin samples from degradation, thus allowing the preparation of large-scale FGT ink in ambient environment.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Electrolytes with moderate lithium polysulfide solubility for high-performance long-calendar-life lithium–sulfur batteries

Lithium–sulfur (Li-S) batteries with high energy density and low cost are promising for next-generation energy storage. However, their cycling stability is plagued by the high solubility of lithium polysulfide (LiPS) intermediates, causing fast capacity decay and severe self-discharge. Exploring electrolytes with low LiPS solubility has shown promising results toward addressing these challenges. However, here, we report that electrolytes with moderate LiPS solubility are more effective for simultaneously limiting the shuttling effect and achieving good Li-S reaction kinetics. We explored a range of solubility from 37 to 1,100 mM (based on S atom, [S]) and found that a moderate solubility from 50 to 200 mM [S] performed the best. Using a series of electrolyte solvents with various degrees of fluorination, we formulated the S ingle- S olvent, S ingle- S alt, S tandard S alt concentration with M oderate L i PSs so l ubility E lectrolytes (termed S 6 MILE ) for Li-S batteries. Among the designed electrolytes, Li-S cells using fluorinated-1,2-diethoxyethane S 6 MILE (F4DEE-S 6 MILE) showed the highest capacity of 1,160 mAh g −1 at 0.05 C at room temperature. At 60 °C, fluorinated-1,4-dimethoxybutane S 6 MILE (F4DMB-S 6 MILE) gave the highest capacity of 1,526 mAh g −1 at 0.05 C and an average CE of 99.89% for 150 cycles at 0.2 C under lean electrolyte conditions. This is a fivefold increase in cycle life compared with other conventional ether-based electrolytes. Moreover, we observed a long calendar aging life, with a capacity increase/recovery of 4.3% after resting for 30 d using F4DMB-S 6 MILE. Furthermore, the correlation between LiPS solubility, degree of fluorination of the electrolyte solvent, and battery performance was systematically investigated.

25 ENERGY STORAGE↗
DOE OSTI2023

High-entropy electrolytes for practical lithium metal batteries

Electrolyte engineering is crucial for improving battery performance, particularly for lithium metal batteries. Recent advances in electrolytes have greatly improved cyclability by enhancing electrochemical stability at the electrode interfaces, but concurrently achieving high ionic conductivity has remained challenging. Here we report an electrolyte design strategy for enhanced lithium metal batteries by increasing the molecular diversity in electrolytes, which essentially leads to high entropy electrolytes (HEEs). We find that in weakly solvating electrolytes, the entropy effect reduces ion clustering while preserving the characteristic anion-rich solvation structures, which is characterized by synchrotron-based X-ray scattering and molecular dynamics simulations. Electrolytes with smaller- sized clusters exhibit a 2-fold improvement in ionic conductivity compared to conventional weakly- solvating electrolytes, enabling stable cycling at high current densities up to 2C (6.2 mA cm -2 ) in anode- free LiNi 0.6 Mn 0.2 Co 0.2 (NMC622)||Cu pouch cells. In conclusion, the efficacy of the design strategy is verified by performance improvements in three disparate weakly solvating electrolyte systems.

25 ENERGY STORAGE↗
DOE OSTI2023

Ultrahigh-Loading Manganese-Based Electrodes for Aqueous Batteries via Polymorph Tuning

Manganese-based aqueous batteries utilizing Mn 2+ /MnO 2 redox reactions are promising choices for grid-scale energy storage due to their high theoretical specific capacity, high power capability, low-cost, and intrinsic safety with water-based electrolytes. However, the application of such systems is hindered by the insulating nature of deposited MnO 2 , resulting in low normalized areal loading (0.005–0.05 mAh cm -2 ) during the charge/discharge cycle. Here, in this work, the electrochemical performance of various MnO 2 polymorphs in Mn 2+ /MnO 2 redox reactions is investigated, and ε-MnO 2 with low conductivity is determined to be the primary electrochemically deposited phase in normal acidic aqueous electrolyte. It is found that increasing the temperature can change the deposited phase from ε-MnO 2 with low conductivity to γ-MnO 2 with two order of magnitude increase in conductivity. It is demonstrated that the highly conductive γ-MnO 2 can be effectively exploited for ultrahigh areal loading electrode, and a normalized areal loading of 33 mAh cm -2 is achieved. At a mild temperature of 50 °C, cells are cycled with an ultrahigh areal loading of 20 mAh cm -2 (1–2 orders of magnitude higher than previous studies) for over 200 cycles with only 13% capacity loss.

25 ENERGY STORAGE↗
DOE OSTI2023

LiH formation and its impact on Li batteries revealed by cryogenic electron microscopy

Little is known about how evolved hydrogen affects the cycling of Li batteries. Hypotheses include the formation of LiH in the solid-electrolyte interphase (SEI) and dendritic growth of LiH. Here, we discover that LiH formation in Li batteries likely follows a different pathway: Hydrogen evolved during cycling reacts to nucleate and grow LiH within already deposited Li metal, consuming active Li. We provide the evidence that LiH formed in Li batteries electrically isolates active Li from the current collector that degrades battery capacity. We detect the coexistence of Li metal and LiH also on graphite and silicon anodes, showing that LiH forms in most Li battery anode chemistries. Last, we find that LiH has its own SEI layer that is chemically and structurally distinct from the SEI on Li metal. Our results highlight the formation mechanism and chemical origins of LiH, providing critical insight into how to prevent its formation.

25 ENERGY STORAGE↗
DOE OSTI2022

Onboard early detection and mitigation of lithium plating in fast-charging batteries

Fast-charging is considered as one of the most desired features needed for lithium-ion batteries to accelerate the mainstream adoption of electric vehicles. However, current battery charging protocols mainly consist of conservative rate steps to avoid potential hazardous lithium plating and its associated parasitic reactions. A highly sensitive onboard detection method could enable battery fast-charging without reaching the lithium plating regime. Here, we demonstrate a novel differential pressure sensing method to precisely detect the lithium plating event. By measuring the real-time change of cell pressure per unit of charge (dP/dQ) and comparing it with the threshold defined by the maximum of dP/dQ during lithium-ion intercalation into the negative electrode, the onset of lithium plating before its extensive growth can be detected with high precision. In addition, we show that by integrating this differential pressure sensing into the battery management system (BMS), a dynamic self-regulated charging protocol can be realized to effectively extinguish the lithium plating triggered by low temperature (0 °C) while the conventional static charging protocol leads to catastrophic lithium plating at the same condition. We propose that differential pressure sensing could serve as an early nondestructive diagnosis method to guide the development of fast-charging battery technologies.

25 ENERGY STORAGE↗
DOE OSTI2022

Cold-Starting All-Solid-State Batteries from Room Temperature by Thermally Modulated Current Collector in Sub-Minute

All-solid-state batteries (ASSBs) show great potential as high-energy and high-power energy storage devices but their attainable energy/power density at room temperature is severely reduced because of the sluggish kinetics of lithium-ion transport. Here we first reported a thermally modulated current collector (TMCC), which can rapidly cold-start ASSBs from room temperature to operating temperatures (70–90 °C) in less than one minute, and simultaneously enhance the transient peak power density by 15-fold compared to one without heating. This TMCC is prepared by integrating a uniform, ultrathin (~200 nm) nickel layer as a thermal modulator within an ultralight polymer-based current collector. By isolating the thermal modulator from the ion/electron pathway of ASSBs, it can provide fast, stable heat control yet does not interfere with regular battery operation. Moreover, this ultrathin (13.2 μm) TMCC effectively shortens the heat transfer pathway, minimizes heat losses, and mitigates the formation of local hot spots. The simulated heating energy consumption can be as low as ~3.94% of total battery energy. This TMCC design with good tunability opens new frontiers towards smart energy storage devices in the future from the current collector perspective.

25 ENERGY STORAGE↗
DOE OSTI2022

Scalable, Ultrathin, and High-Temperature-Resistant Solid Polymer Electrolytes for Energy-Dense Lithium Metal Batteries

We report all-solid-state batteries (ASSBs) demonstrate great promise, offering high energy density, good thermal stability, and safe operation compared with traditional Li-ion batteries. Among various solid-state electrolytes (SSEs), solid polymer electrolytes (SPEs) offer an attractive choice due to their thinness, low density, and good manufacturability. However, ultrathin SPEs that work with practical current densities or at high temperatures remain challenging, limiting applicable conditions of SPE-based batteries. Here, the authors report a novel scalable, ultrathin, and high-temperature-resistant SPE for ASSBs. This design includes an electrospun polyacrylonitrile (PAN) matrix and polyethylene oxide (PEO)/Li salt ionic conductor, which offers a stable LiF and Li 3 N containing SSE/Li interface. The unique interface—as well as the good mechanical strength—inhibits lithium dendrites and prevents short circuiting. As a result, symmetrical Li-Li cells deliver more than 300 h cyclability at 0.5 mA cm -2 . ASSBs fabricated with only 5 µm-thickness PAN-PEO/lithium bis(trifluoromethanesulfonyl)imide reach 300 cycles at 0.3 C rate at 60 °C. The excellent thermal stability of PAN also results in safer SPEs at high temperatures. The design extends battery operation up to temperatures of 120 and 150 °C, where it achieves 500 cycles at C/2 rate and 100 cycles at 2C rate, respectively.

25 ENERGY STORAGE↗
DOE OSTI2022

Capturing the swelling of solid-electrolyte interphase in lithium metal batteries

Although liquid-solid interfaces are foundational in broad areas of science, characterizing this delicate interface remains inherently difficult because of shortcomings in existing tools to access liquid and solid phases simultaneously at the nanoscale. This leads to substantial gaps in our understanding of the structure and chemistry of key interfaces in battery systems. We adopt and modify a thin film vitrification method to preserve the sensitive yet critical interfaces in batteries at native liquid electrolyte environments to enable cryo–electron microscopy and spectroscopy. We report substantial swelling of the solid-electrolyte interphase (SEI) on lithium metal anode in various electrolytes. Here, the swelling behavior is dependent on electrolyte chemistry and is highly correlated to battery performance. Higher degrees of SEI swelling tend to exhibit poor electrochemical cycling.

25 ENERGY STORAGE↗
DOE OSTI2021

Coloured low-emissivity films for building envelopes for year-round energy savings

We report that buildings are responsible for over 40% of total US energy use, of which about 40% is directly related to the operation of heating, ventilation and air-conditioning (HVAC) systems. Saving energy to heat and cool buildings would contribute substantially to sustainability. Here we propose a category of coloured low-emissivity films for building walls that constitute the main component of the building thermal envelope. We demonstrate high reflectance (~90%) in infrared wavelength range and selective reflectance in the visible light wavelength range for desired colours. These films can help minimize radiative heat exchange between the indoor and outdoor environments, thus saving energy for all-year cooling and heating while satisfying the required aesthetical effect. Simulations show that these films can help reduce heat gain and loss by up to 257.6 MJ per installation wall area annually. In the case of a typical midrise apartment building, the HVAC system can save up to 124.46 GJ (equal to 9.87% of the building’s HVAC energy consumption). By rough estimation, a global CO 2 emission reduction of 1.14 billion metric tons annually could be achieved. Our work provides insights for innovative energy-saving building envelope materials that can help achieve global carbon neutrality and sustainability.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Dynamic spatial progression of isolated lithium during battery operations

The increasing demand for next-generation energy storage systems necessitates the development of high-performance lithium batteries. Unfortunately, current Li anodes exhibit rapid capacity decay and a short cycle life, owing to the continuous generation of solid electrolyte interface and isolated Li (i-Li). The formation of i-Li during the nonuniform dissolution of Li dendrites leads to a substantial capacity loss in lithium batteries under most testing conditions. Because i-Li loses electrical connection with the current collector, it has been considered electrochemically inactive or ‘dead’ in batteries. In this work, contradicting this commonly accepted presumption, we show that i-Li is highly responsive to battery operations, owing to its dynamic polarization to the electric field in the electrolyte. Simultaneous Li deposition and dissolution occurs on two ends of the i-Li, leading to its spatial progression toward the cathode (anode) during charge (discharge). Revealed by our simulation results, the progression rate of i-Li is mainly affected by its length, orientation and the applied current density. Moreover, we successfully demonstrate the recovery of i-Li in Cu–Li cells with >100% Coulombic efficiency and realize LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC)–Li full cells with extended cycle life.

25 ENERGY STORAGE↗
DOE OSTI2021

All-Solid-State Lithium–Sulfur Batteries Enhanced by Redox Mediators

We report redox mediators (RMs) play a vital role in some liquid electrolyte-based electrochemical energy storage systems. However, the concept of redox mediator in solid-state batteries remains unexplored. Here, we selected a group of RM candidates and investigated their behaviors and roles in all-solid-state lithium-sulfur batteries (ASSLSBs). The soluble-type quinone-based RM (AQT) shows the most favorable redox potential and the best redox reversibility that functions well for lithium sulfide (Li 2 S) oxidation in solid polymer electrolytes. Accordingly, Li 2 S cathodes with AQT RMs present a significantly reduced energy barrier (average oxidation potential of 2.4 V) during initial charging at 0.1 C at 60 °C and the following discharge capacity of 1133 mAh g s -1 . Using operando sulfur K-edge X-ray absorption spectroscopy, we directly tracked the sulfur speciation in ASSLSBs and proved that the solid-polysulfide-solid reaction of Li 2 S cathodes with RMs facilitated Li 2 S oxidation. In contrast, for bare Li 2 S cathodes, the solid-solid Li 2 S-sulfur direct conversion in the first charge cycle results in a high energy barrier for activation (charge to ~4 V) and low sulfur utilization. The Li 2 S@AQT cell demonstrates superior cycling stability (average Coulombic efficiency 98.9% for 150 cycles) and rate capability owing to the effective AQT-enhanced Li-S reaction kinetics. This work reveals the evolution of sulfur species in ASSLSBs and realizes the fast Li-S reaction kinetics by designing an effective sulfur speciation pathway

25 ENERGY STORAGE↗
DOE OSTI2021

A Morphologically Stable Li/Electrolyte Interface for All-Solid-State Batteries Enabled by 3D-Micropatterned Garnet

Morphological degradation at the Li/solid-state electrolyte (SSE) interface is a prevalent issue causing performance fading of all-solid-state batteries (ASSBs). To maintain the interfacial integrity, most ASSBs are operated under low current density with considerable stack pressure, which significantly limits their widespread usage. In this work, a novel 3D-micropatterned SSE (3D-SSE) that can stabilize the morphology of the Li/SSE interface even under relatively high current density and limited stack pressure is reported. Under the pressure of 1.0 MPa, the Li symmetric cell using a garnet-type 3D-SSE fabricated by laser machining shows a high critical current density of 0.7 mA cm –2 and stable cycling over 500 h under 0.5 mA cm –2 . This excellent performance is attributed to the reduced local current density and amplified mechanical stress at the Li/3D-SSE interface. These two effects can benefit the flux balance between Li stripping and creep at the interface, thereby pre-venting interfacial degradation such as void formation and dendrite growth.

3D-micropatterned garnet↗
DOE OSTI2021

Oxygen-deficient ammonium vanadate for flexible aqueous zinc batteries with high energy density and rate capability at -30 °C

Aqueous zinc batteries (AZBs) have received significant attention owing to environmental friendliness, high energy density and inherent safety. However, lack of high-performance cathodes has become the main bottleneck of AZBs development. Here, oxygen-deficient NH 4 V 4 O 10–x ·nH 2 O (NVOH) microspheres are synthesized and used as cathodes for AZBs. The experimental test and theoretical calculations demonstrate that the oxygen vacancies in the lattice lower the Zn 2+ diffusion energy barrier, which enables fast Zn 2+ diffusion and good electrochemical performance in a wide temperature range. The suppressed side reactions also can help to improve the low temperature performance. NVOH shows a high energy density of 372.4 Wh kg –1 and 296 Wh kg –1 at room temperature and –30 °C, respectively. Moreover, NVOH maintains a 100% capacity retention after 100 cycles at 0.1 A g –1 and ~94% capacity retention after 2600 cycles at 2 A g –1 and –30 °C. Investigation into the mechanism of the process reveals that the capacity contribution of surface capacitive behaviors is dominant and capacity attenuation is mainly caused by the decay of diffusion-controlled capacity. As a result, flexible AZBs can steadily power portable electronics under different bending states, demonstrating its great potential in wide-temperature wearable device.

25 ENERGY STORAGE↗