Engineering Papers⌕ Search

Engineering topics

Ye, B.

Publications and source records attributed to Ye, B..

Contributions to the mechanistic understanding of the microstructural evolution in irradiated U-Mo dispersion fuel

Here, advanced microstructural characterization techniques, such as scanning electron microscopy (SEM) and scanning transmission electron microscopy - energy dispersive x-ray spectroscopy (STEM-EDS), were used to interpret the fuel microstructure evolution and fission products behavior in U-Mo dispersion fuel irradiated in the Advanced Test Reactor (ATR) as part of the European Mini-Plate Irradiation Experiment (EMPIrE) test. The larger as-fabricated fuel grain size achieved by heat-treating the U-Mo powder resulted in slower high burnup structure (HBS) development and reduced fission gas porosity. Slower HBS kinetics was observed at the fuel kernels’ periphery, which contained smaller and less fission gas bubbles at all fission densities (FDs) investigated and was attributed to a locally reduced damage density and fission products concentration, as corroborated with Monte Carlo simulations. The non-refined grains at the fuel kernel periphery hosted a perfectly ordered fission Gas Bubble Superlattice (GBS) up to 6.3 × 10 21 fissions/cm 3 . Nano-scale STEM-EDS analysis presented in this study provided useful information on the GBS characteristic morphology and evolution in U-Mo fuel. The concentration of fission gas in the GBS progressively increased with FD, pointing to an evolution of the nanobubble pressure status with irradiation. A possible connection between the GBS collapse and HBS onset is proposed for which there exists a threshold in the misorientation of the refined sub-grains above which the GBS stability during irradiation is no longer preserved, resulting in the GBS collapse.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

ZrN coating as diffusion barrier in U(Mo) dispersion fuel systems

The control of the interaction between the U(Mo) fuel phase and the Al matrix is one of the challenges of dispersion fuel plate development for research reactors. Given the specific properties of this interaction layer, larger amounts of it in the meat could lead to a reduction of the plate mechanical integrity and thermal conductivity, eventually leading to pillowing. The SELENIUM project showed that by depositing a ZrN coating on the surface of the U(Mo) fuel particles, the amount of formed U(Mo)-Al interaction layer is limited but still present. Microstructural analysis performed on the as fabricated coating and fresh fuel plates containing ZrN coated U(Mo) dispersed in an Al matrix, revealed that the coating gets damaged during plate production. The post irradiation examinations (PIE) of the ZrN coated U(Mo) fuel plates, from the SELENIUM and SEMPER FIDELIS experiments, show how the U(Mo)-Al interaction layer is formed -only at those locations where the coating is missing or damaged -and the evolution of coating microstructure during irradiation. Finally, as a remedy, to further reduce the amount of interaction layer formed, the use of an Al-Si matrix was proposed based on the higher affinity of Si for U compared to the affinity of Al for U. PIE of a fuel plate consisting of ZrN coated U(Mo) dispersed in an Al-Si matrix irradiated in the SEMPER FIDELIS experiment, clearly demonstrates the benefit of adding Si to the matrix.

36 MATERIALS SCIENCE↗

Temperature Effects on Interdiffusion of Al and U-Mo under Irradiation

A high-energy Xe ion irradiation experiment was conducted to investigate the temperature dependence of interdiffusion in bilayer Al-UMo samples under irradiation. The amount of interdiffusion achieved at a fixed dose with the increase of temperature showed a clear transition at 175 degrees C (with an estimated error in the range of ± 10 degrees C) from temperature-independent to temperature-dependent behavior. The activation energy derived from the curve of interdiffusion quantity vs. irradiation temperature is 0.77 ± 0.16 eV. This information has been utilized to understand the temperature effect on the interdiffusion process that occurred at the interfaces of U-Mo particles and the Al matrix in U-Mo/Al dispersion fuels, whose magnitude significantly impacts the fuel's performance. Although this temperature effect was deemed important, it cannot be examined directly using in-pile irradiation data, as fuel temperatures cannot be measured in reactor irradiation and are highly correlated with fission rate and thermal conductivity evolution. To connect the knowledge accumulated from ion irradiation with in-pile irradiation data, simulation of a full-sized U-Mo/Al dispersion fuel plate irradiated in the FUTURE test in the BR2 reactor was performed with the Dispersion Analysis Research Tool (DART), a dispersion fuel performance code. DART is equipped with an interaction or interdiffusion layer (IL) growth correlation formulated to describe the temperature dependence of ion mixing results. The agreement between calculated and measured fuel meat constituent volume fractions and swelling data demonstrated that the temperature effect on in-pile Al-UMo interdiffusion is well captured with the correlation. In this case, the fitted activation energy is 0.70 eV. Considering the uncertainties associated with the ion irradiation data, the activation energy obtained from in-pile data fitting is in accord with that from ion irradiation results.

36 MATERIALS SCIENCE↗

Effectiveness of the metal coating on U–7Mo dispersion fuel in Al during irradiation

The effectiveness of a transition metal coating layer as a diffusion barrier between the UMo and matrix Al was examined. The samples were cut from KAERI-made U-Mo/Al dispersion miniplates containing 8 gU/cm 3 fuel meat. Mo, W and Zr were included as coating candidates. A physical vapor deposition (PVD) method was used to produce about a 0.2-mu m thick coating layer on the UMo. An Al protection coating layer was subsequently applied to protect the main coating layer. The samples were irradiated at the ATLAS facility in Argonne National laboratory with 84-MeV Xe 26+ ions, with the beam current of 200 particles nano ampere (pnA), to achieve a final dose of 2.7x10 17 ions/cm 2 . Post-irradiation examinations included focused ion beam (FIB), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). Furthermore, among the coating metals, Mo showed the highest survival during the fuel plate fabrication and endurance during irradiation, which was consistent with the pre-irradiation thermodynamics evaluation. This result also emphasized the importance of the Al protection layer.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A REPORT: “HIGH-DENSITY U-MO/AL AND U3SI2/AL DISPERSION FUELS FOR HIGH-POWER RESEARCH REACTORS”

An introduction to a new report on high-density U-Mo/Al and U3Si2/Al dispersion fuels for high power research reactors that ANL is drafting is given in this paper. The main objective of this report is to produce a stand-alone data compilation that can be used by fuel designers, fuel performance analyzers, and fuel safety evaluators, as well as reactor operators. It is also intended to build a foundation for an eventual U-Mo/Al dispersion fuel qualification report that supports the licensing of this fuel for high-power research reactors. U-silicide dispersion fuel is also included in the report for potential applications beyond the ranges of the fuel licensed in NUREG-1313 (Safety Evaluation Report for U3Si2/Al). The contents and framework of the dispersion fuel report is described. A gap analysis provides a summary of the areas where sufficient data and information are not currently available.

Research reactor fuel, U-Si, U-Mo↗

Cross section TEM characterization of high-energy-Xe-irradiated U-Mo

U-Mo alloys irradiated with 84 MeV Xe ions to various doses were characterized with transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM) techniques. The TEM thin foils were prepared perpendicular to the irradiated surface to allow a direct observation of the entire region modified by ions. Furthermore, depth-selective microstructural information was revealed. Varied irradiation-induced phenomena such as gas bubble formation, phase reversal, and recrystallization were observed at different ion penetration depths in U-Mo.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fission gas swelling in U{sub 3}Si{sub 2} at LWR conditions

In order to evaluate the feasibility of replacing uranium dioxide fuel with U{sub 3}Si{sub 2} fuel, it is crucial to examine the fuel performance of the silicide fuel under typical LWR conditions. At this early stage of U{sub 3}Si{sub 2} fuel development, before undertaking costly in-pile irradiation experiments and corresponding post-irradiation examinations, it is appropriate to utilize modeling tools to estimate the behavior of U{sub 3}Si{sub 2} in LWRs based on available in-pile irradiation experiments as well as the state-of-the-art calculation capabilities provided by density functional theory (DFT). Therefore, a comprehensive investigation of the fission gas swelling behavior of U{sub 3}Si{sub 2} at LWR conditions is reported here. The modeling efforts in this study are based on the Gas Release and Swelling Subroutine for Steady-State and Transient (GRASS-SST) rate theory (RT) model of fission gas bubble evolution that has been successfully applied to a variety of fuel materials in numerous types of reactors. Both existing in-pile irradiation data and DFT-based calculations were used for the optimized parametrization of the RT model. In addition, the fuel-cladding interaction was captured by coupling the RT model with simplified mechanical correlations. Both the swelling behavior and the fission gas bubble size distribution were predicted by the rate theory model. At LWR conditions, the RT model predicts that intragranular bubbles dominate the gaseous swelling behavior and that the evolution of intergranular bubbles and corresponding gas release are suppressed, confirming the qualification of U{sub 3}Si{sub 2} as a LWR fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High-energy synchrotron study of in-pile-irradiated U–Mo fuels

Here synchrotron scattering analysis results on U–7wt.%Mo fuel specimens irradiated in the Advanced Test Reactor to three burnup levels (3.0, 5.2, and 6.3 × 1021 fission/cm3) are reported. Mature fission gas bubble superlattice was observed to form at intermediate burnup. The superlattice constant was determined to be 11.7 and 12.0 nm by wide-angle and small-angle scattering respectively. Grain sub-division takes place throughout the irradiation and causes the collapse of the superlattice at high burnup. The bubble superlattice expands the U–Mo lattice and acts as strong sink for radiation-induced defects. The evolution of dislocation loops was, therefore, suppressed until the bubble superlattice collapsed.

metallic nuclear fuel↗

Multiscale Multiphysics Developments for Accident Tolerant Fuel Concepts

U 3 Si 2 and iron-chromium-aluminum (Fe-Cr-Al) alloys are two of many proposed accident-tolerant fuel concepts for the fuel and cladding, respectively. The behavior of these materials under normal operating and accident reactor conditions is not well known. As part of the Department of Energy’s Accident Tolerant Fuel High Impact Problem program significant work has been conducted to investigate the U 3 Si 2 and FeCrAl behavior under reactor conditions. This report presents the multiscale and multiphysics effort completed in fiscal year 2015. The report is split into four major categories including Density Functional Theory Developments, Molecular Dynamics Developments, Mesoscale Developments, and Engineering Scale Developments. The work shown here is a compilation of a collaborative effort between Idaho National Laboratory, Los Alamos National Laboratory, Argonne National Laboratory and Anatech Corp.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Dependence of Cumulus Anvil Radiative Properties on Environmental Conditions in the Tropical West Pacific

Areally extensive, optically thick anvil clouds associated with mesoscale convective clusters dominate the shortwave cloud forcing in the tropics and provide longwave forcing comparable to that of thin cirrus. Changes in the cover and optical thickness of tropical anvils as climate warms can regulate the sign of cloud feedback. As a prelude to the study of MMCR data from the ARM TWP sites, we analyze ISCCP-derived radiative characteristics of anvils observed in the tropical west Pacific during the TOGA-COARE IOP. Anvils with radius greater than 100 km were identified and tracked from inception to decay using the Machado-Rossow algorithm. Corresponding environmental conditions just prior to the start of the convectove event were diagnosed using the Lin-Johnson objective analysis product. Small clusters (100-200 km radius) are observed to have a broad range of optical thicknesses (10-50), while intermediate optical thickness clusters are observed to range in size from 100 km to almost 1000 km. Large-size clusters appear to be favored by strong pre-storm large scale upward motion throughout the troposphere, moist low-to-midlevel relative humidities, environments with slightly higher CAPE than those for smaller clusters, and strong front-to-rear flow. Optically thick anvils are favored in situations of strong low-level moisture convergence and strong upper-level shear.

Ye, B.↗