Engineering Papers⌕ Search

Engineering topics

Yang, Yang

Publications and source records attributed to Yang, Yang.

At least 217 records · Page 12

Evaluation of Global Simulations of Aerosol Particle and Cloud Condensation Nuclei Number, with Implications for Cloud Droplet Formation

A total of 16 global chemistry transport models and general circulation models have participated in this study; 14 models have been evaluated with regard to their ability to reproduce the near-surface observed number concentration of aerosol particles and cloud condensation nuclei (CCN), as well as derived cloud droplet number concentration (CDNC). Model results for the period 2011-2015 are compared with aerosol measurements (aerosol particle number, CCN and aerosol particle composition in the submicron fraction) from nine surface stations located in Europe and Japan. The evaluation focuses on the ability of models to simulate the average across time state in diverse environments and on the seasonal and short-term variability in the aerosol properties. There is no single model that systematically performs best across all environments represented by the observations. Models tend to underestimate the observed aerosol particle and CCN number concentrations, with average normalized mean bias (NMB) of all models and for all stations, where data are available, of -24% and -35% for particles with dry diameters > 50 and > 120nm, as well as -36% and -34% for CCN at supersaturations of 0.2% and 1.0%, respectively. However, they seem to behave differently for particles activating at very low supersaturations (< 0.1%) than at higher ones. A total of 15 models have been used to produce ensemble annual median distributions of relevant parameters. The model diversity (defined as the ratio of standard deviation to mean) is up to about 3 for simulated N3 (number concentration of particles with dry diameters larger than 3 nm) and up to about 1 for simulated CCN in the extra-polar regions. A global mean reduction of a factor of about 2 is found in the model diversity for CCN at a supersaturation of 0.2% (CCN(0.2)) compared to that for N3, maximizing over regions where new particle formation is important. An additional model has been used to investigate potential causes of model diversity in CCN and bias compared to the observations by performing a perturbed parameter ensemble (PPE) accounting for uncertainties in 26 aerosol-related model input parameters. This PPE suggests that biogenic secondary organic aerosol formation and the hygroscopic properties of the organic material are likely to be the major sources of CCN uncertainty in summer, with dry deposition and cloud processing being dominant in winter. Models capture the relative amplitude of the seasonal variability of the aerosol particle number concentration for all studied particle sizes with available observations (dry diameters larger than 50, 80 and 120nm). The short-term persistence time (on the order of a few days) of CCN concentrations, which is a measure of aerosol dynamic behavior in the models, is underestimated on average by the models by 40% during winter and 20% in summer.

cloud droplets↗

Large plasticity in magnesium mediated by pyramidal dislocations

Lightweight magnesium alloys are attractive as structural materials for improving energy efficiency in applications such as weight reduction of transportation vehicles. One major obstacle for widespread applications is the limited ductility of magnesium, which has been attributed to $\langle$c+a$\rangle$ dislocations failing to accommodate plastic strain. We demonstrate, using in situ transmission electron microscope mechanical testing, that $\langle$c+a$\rangle$ dislocations of various characters can accommodate considerable plasticity through gliding on pyramidal planes. We found that submicrometer-size magnesium samples exhibit high plasticity that is far greater than for their bulk counterparts. Small crystal size usually brings high stress, which in turn activates more $\langle$c+a$\rangle$ dislocations in magnesium to accommodate plasticity, leading to both high strength and good plasticity.

Science & Technology - Other Topics↗

FastProNGS: fast preprocessing of next-generation sequencing reads

Background Next-generation sequencing technology is developing rapidly and the vast amount of data that is generated needs to be preprocessed for downstream analyses. Yet, until now, software that can efficiently make all the quality assessments and filtration of raw data is still lacking. Results We developed FastProNGS to integrate the quality control process with automatic adapter removal. Parallel processing was implemented to speed up the process by allocating multiple threads. Compared with similar up-to-date preprocessing tools, FastProNGS is by far the fastest. Read information before and after filtration can be output in plain-text, JSON, or HTML formats with user-friendly visualization. Conclusions FastProNGS is a rapid, standardized, and user-friendly tool for preprocessing next-generation sequencing data within minutes. It is an all-in-one software that is convenient for bulk data analysis. It is additionally very flexible and can implement different functions using different user-set parameter combinations.

97 MATHEMATICS AND COMPUTING↗

Quantification of Heterogeneous Degradation in Li-Ion Batteries

The multiscale chemomechanical interplay in lithium-ion batteries builds up mechanical stress, provokes morphological breakdown, and leads to state of charge heterogeneity. Quantifying the interplay in complex composite electrodes with multiscale resolution constitutes a frontier challenge in precisely diagnosing the fading mechanism of batteries. In this work, hard X-ray phase contrast tomography, capable of nanoprobing thousands of active particles at once, enables an unprecedented statistical analysis of the chemomechanical transformation of composite electrodes under fast charging conditions. The damage heterogeneity is demonstrated to prevail at all length scales, which stems from the unbalanced electron conduction and ionic diffusion, and collectively leads to the nonuniform utilization of active particles spatially and temporally. This research highlights that the statistical mapping of the chemomechanical transformation offers a diagnostic method for the particles utilization and fading, hence could improve electrode formulation for fast-charging batteries.

25 ENERGY STORAGE↗

Enhancing the applicability of multicomponent time-dependent density functional theory

The multicomponent extension of time-dependent density functional theory (TDDFT) within the nuclear-electronic orbital (NEO) framework enables the calculation of both electronic and vibrational excitations simultaneously. In this NEO-TDDFT approach, all electrons and select nuclei, typically protons, are treated quantum mechanically on the same level. Herein, the dependence of the proton vibrational excitation energies on the nuclear and electronic basis sets is examined. Protonic basis sets that include f basis functions in conjunction with substantial electronic basis sets for the quantum hydrogen are found to produce accurate proton vibrational excitation energies that are mostly within ~30 cm -1 of reference values for the molecules studied. The NEO-TDDFT approach is shown to be effective for open-shell as well as closed-shell systems. Additionally, an approach for computing and visualizing the nuclear transition densities associated with the proton vibrational excitations is implemented. These nuclear transition densities are important for characterizing the proton vibrational excitations and determining the spatial orientations of the corresponding vibrational modes. These capabilities are essential for a variety of applications, including the incorporation of anharmonic effects into molecular vibrational frequency calculations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Alloying and embedding of Cu-core/Ag-shell nanowires for ultrastable stretchable and transparent electrodes

In this paper, transparent electrodes with dense Cu@Ag alloy nanowires embedded in stretchable substrates are successfully fabricated by a high-intensity pulsed light (HIPL) technique within one step. The intense light energy not only induces rapid mutual dissolution between the Cu core and the Ag shell to form dense Cu@Ag alloy nanowires but also embeds the newly formed alloy nanowires into the stretchable substrates. The synergetic effects of alloy nanowires and embedded structures greatly improve the thermal stability of the transparent electrodes that keep high conductivity unchanged in both high temperature (140 °C) and high humidity (85 °C, 85% RH) for at least 500 h, which is much better than previous reports. The transparent electrodes also exhibit high electro-mechanical stability due to the strong adhesion between alloy nanowires and substrates, which remain stable after 1000 stretching-relaxation cycles at 30% strain. Stretchable and transparent heaters based on the alloyed and embedded electrodes have a wide outputting temperature range (up to 130 °C) and show excellent thermal stability as well as stretchability (up to 60% strain) due to the alloy nanowires and embedded structures. To sum up, this study proposes the synergetic effects of alloying and embedded structures to greatly improve the stability of Cu nanowirebased stretchable transparent electrodes, showing a huge application prospect in the field of stretchable and wearable electronics.

Zhang, Bowen↗

Heterogeneous damage in Li-ion batteries: Experimental analysis and theoretical modeling

We assess the heterogeneous electrochemistry and mechanics in a composite electrode of commercial batteries using synchrotron X-ray tomography analysis and microstructure-resolved computational modeling. We visualize the morphological defects at multi-scales ranging from the macroscopic composite, particle ensembles, to individual single particles. Particle fracture and interfacial debonding are identified in a large set of tomographic data of active particles. Mechanical failure in the regime near the separator is more severe than toward the current collector. The active particles close to the separator experience deeper charge and discharge over cycles and thus are more mechanically loaded. The difference in the Li activity originates from the polarization of the electrolyte potential and the non-uniform distribution of the activation energy for the charge transfer reaction. We model the kinetics of intergranular fracture and interfacial degradation to confirm that the various Li activities are the major cause of the heterogeneous damage. The interfacial failure may reconstruct the conductive network and redistribute the electrochemical activities that render a dynamic nature of electrochemistry and mechanics evolving over time in the composite electrode. We further quantify the influence of the mechanical damage on the metrics of battery performance. We simulate the electrochemical impedance profile to build a relationship between the interfacial debonding and the impedance of electron transport and surface charge transfer. Lastly, the mechanical failure disrupts the conduction path of electrons and results in significant polarization and capacity loss in batteries.

25 ENERGY STORAGE↗

Stretchable Mould Interconnect Optimization: Peeling Automation and Carrierless Techniques

The primary bottleneck of the stretchable mold interconnect (SMI) technology is its reliance on carrier boards. These are necessary to handle the meandered circuit during production and to ensure dimensional stability of the flexible circuit board before encapsulation. However, for all the problems it solves, it also introduces a new major problem by requiring a peeling step – which is difficult to automate. This manuscript aims to present some of the work that went into eliminating this problem, discussing both unsuccessful and functioning methods to tackle this conundrum and some of the experimental work that went into verifying these techniques. First, alterations to the design to simplify peeling are considered, followed by adhesivebased peeling processes and mechanical pin-based systems. Next, masking and structuring of the carrier board adhesive are considered. Finally, two carrierless methods which circumvent the problems are discussed, a two-step process – which cuts temporary support structures after partial encapsulation – and a technique whereby the frame is designed to fail in a controlled manner during the first use of the circuit, creating a carrierless process feasible for high-volume production.

Plovie, Bart↗

Electronic Structure and Linhard Function of Iron-Based Superconductor La{sub 0.5−x}Na{sub 0.5 + x}Fe{sub 2}As{sub 2}

We perform theoretical studies of the iron-based superconductor La{sub 0.5−x}Na{sub 0.5 + x}Fe{sub 2}As{sub 2}. Using density functional calculation with virtual crystal approximation, band structures, density of states, and Fermi surfaces are obtained for different La/Na composition by varying x value. Furthermore, the nesting property is also investigated using the Linhard function. Our main findings are as follows: For undoped (x = 0.0) case, the magnetic and electronic structure share great similarities with extensively studied BaFe{sub 2}As{sub 2}. Upon hole doping (x = 0.3), the Q = (π,π) nesting property are preserved. However, upon electron doping (x = -0.3), the Fermi surfaces undergo a dramastic change into 3D and complex structure. We find this change is attributed to the comprehensive influence of band filling and chemical pressure of La{sup 3+}. We propose the asymmetric change of Fermi surfaces upon doping may in some sense explain the electron-hole asymmetry in phase diagram.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Impact of Anthropogenic Emission Injection Height Uncertainty on Global Sulfur Dioxide and Aerosol Distribution

Anthropogenic sulfur compounds play an important role in acid deposition, aerosol particle formation, and subsequent radiative forcing and human fine particulate exposure. There are substantial uncertainties in processes influencing sulfate and precursor distributions, however, that have not yet been resolved through comparisons with observations. We find here an underappreciated factor that has a large impact on model results: uncertain emission height. Global aerosol-climate model simulations indicate that the assumed effective anthropogenic emission height is very important to SO 2 near-surface concentrations and vertical profile. The global range of near-surface SO 2 concentration over land (ocean) due to uncertainty in industrial (international shipping) emission injection height is 81% (76%), relative to the average concentration. This sensitivity is much larger than the uncertainty of SO 2 emission rates. Black carbon and primary organic matter concentration and profiles are also sensitive to emission heights (53% over land and 28% over oceans). The impact of emission height uncertainty is larger in winter for land-based emissions, but larger in summer over the Northern Hemisphere ocean for shipping emissions. The variation in aerosol optical depth related to shipping emission injection heights is 11% over oceans, revealing the potential importance of injection height on aerosol forcing and climatic effects. The large impact on SO 2 concentrations can confound attempts to use surface, aircraft, and satellite observations to constrain the importance of other processes that govern sulfur compound distributions in the atmosphere. In conclusion, the influence of emission height on vertical SO 2 column also will impact the accuracy of satellite retrievals.

54 ENVIRONMENTAL SCIENCES↗

High-Voltage Charging-Induced Strain, Heterogeneity, and Micro-Cracks in Secondary Particles of a Nickel-Rich Layered Cathode Material

Nickel-rich layered materials LiNi 1-x-y Mn x Co y O 2 are promising candidates for high-energy-density lithium-ion battery cathodes. Unfortunately, they suffer from capacity fading upon cycling, especially with high-voltage charging. It is critical to have a mechanistic understanding of such fade. Synchrotron-based techniques (including scattering, spectroscopy, and microcopy) and finite element analysis are utilized to understand the LiNi 0.6 Mn 0.2 Co 0.2 O 2 material from structural, chemical, morphological, and mechanical points of view. The lattice structural changes are shown to be relatively reversible during cycling, even when 4.9 V charging is applied. However, local disorder and strain are induced by high-voltage charging. Nano-resolution 3D transmission X-ray microscopy data analyzed by machine learning methodology reveal that high-voltage charging induced significant oxidation state inhomogeneities in the cycled particles. Regions at the surface have a rock salt–type structure with lower oxidation state and build up the impedance, while regions with higher oxidization state are scattered in the bulk and are likely deactivated during cycling. In addition, the development of micro-cracks is highly dependent on the pristine state morphology and cycling conditions. Hollow particles seem to be more robust against stress-induced cracks than the solid ones, suggesting that morphology engineering can be effective in mitigating the crack problem in these materials.

25 ENERGY STORAGE↗

Variability, timescales, and nonlinearity in climate responses to black carbon emissions

Black carbon (BC) particles exert a potentially large warming influence onthe Earth system. Reductions in BC emissions have attracted attention as apossible means to moderate near-term temperature changes. For the first time,we evaluate regional climate responses, nonlinearity, and short-termtransient responses to BC emission perturbations in the Arctic, midlatitudes,and globally based on a comprehensive set of emission-driven experimentsusing the Community Earth System Model (CESM). Surface temperature responsesto BC emissions are complex, with surface warming over land from midlatitudeBC perturbations partially offset by ocean cooling. Climate responses do notscale linearly with emissions. While stronger BC emission perturbations havea higher burden efficiency, their temperature sensitivity is lower. BCimpacts temperature much faster than greenhouse gas forcing, with transienttemperature responses in the Arctic and midlatitudes approaching aquasi-equilibrium state with a timescale of 2–3 years. We find largevariability in BC-induced climate changes due to background model noise. As aresult, removing present-day BC emissions results in discernible surfacetemperature changes for only limited regions of the globe. In order to betterunderstand the climatic impacts of BC emissions, both the drivers ofnonlinear responses and response variability need to be assessed acrossclimate models.

54 ENVIRONMENTAL SCIENCES↗

Large-Scale and Galvanic Replacement Free Synthesis of Cu@Ag Core–Shell Nanowires for Flexible Electronics

Copper nanowires (CuNWs) are considered a promising alternative to indium tin oxide (ITO) due to their high transparency, conductivity and low cost. However, the susceptibility to oxidation of copper in ambient conditions largely overshadows their practical applications. Here, a facile adsorption and subsequent heat-treatment method is developed to obtain uniform Cu@Ag core-shell nanowires. Ag-ammonia complex (Ag[(NH2R)2]+) as silver source adsorbs on the surface of CuNWs to form Cu@Ag-ammonia core-shell precursors and then decomposes to pure Ag shell through a simple thermal annealing process under air. The thickness of Ag shell can easily be controlled by adjusting the concentration of Ag-ammonia. The Ag shell perfectly prevents the oxidation of CuNWs, enabling the core-shell nanowires to maintain stability at high temperature (140 °C) and high humidity (85 °C, 85% RH) for at least 500 h. More importantly, transparent conductive films made from our Cu@Ag nanowires hold comparable optical and electrical properties to pure CuNWs. The large-scale and facile strategy demonstrated in this study offers huge potential to further explore the applications of CuNWs in flexible and stretchable electronic and optoelectronic devices.

Zhang, Bowen (ORCID:000000030432745X)↗