Engineering Papers⌕ Search

Engineering topics

Yang, L H

Publications and source records attributed to Yang, L H.

Anharmonicity-induced first-order isostructural phase transition of zirconium under pressure

We have performed a detailed x-ray diffraction structural study of Zr under pressure and unambiguously identify the existence of a first-order isostructural bcc-to-bcc phase transition near 58 GPa. First-principles quantum molecular dynamics calculations support the existence of this phase transition, in excellent agreement with experimental results, triggered by anharmonic effects. Lastly, our results highlight the potential ubiquity of anharmonically driven isostructural transitions within the periodic table under pressure and call for follow-up experimental and theoretical studies.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

WHY IS THE SOLAR CONSTANT NOT A CONSTANT?

In order to probe the mechanism of variations of the solar constant on the inter-solar-cycle scale, the total solar irradiance (TSI; the so-called solar constant) in the time interval of 1978 November 7 to 2010 September 20 is decomposed into three components through empirical mode decomposition and time-frequency analyses. The first component is the rotation signal, counting up to 42.31% of the total variation of TSI, which is understood to be mainly caused by large magnetic structures, including sunspot groups. The second is an annual-variation signal, counting up to 15.17% of the total variation, the origin of which is not known at this point in time. Finally, the third is the inter-solar-cycle signal, counting up to 42.52%, which is inferred to be caused by the network magnetic elements in quiet regions, whose magnetic flux ranges from (4.27-38.01) Multiplication-Sign 10{sup 19} Mx.

79 ASTRONOMY AND ASTROPHYSICS↗

Preparation and properties of antiperovskite-type nitrides: InNNi{sub 3} and InNCo{sub 3}

Two antiperovskite-type ternary nitrides of InNM{sub 3} (M=Ni, Co) have been synthesized from In{sub 2}O{sub 3} and Ni or Co powders under NH{sub 3} atmosphere at 600 deg. C. InNCo{sub 3} is a new ternary nitride whereas InNNi{sub 3} was previously reported as InN{sub 0.5}Ni{sub 3} with different nitrogen content. The lattice parameters refined by Rietveld method are 3.8445(1) A for InNNi{sub 3} and 3.8541(7) A for InNCo{sub 3}, respectively. Both nitrides show metallic behaviors and below 70 K the T{sup 2} temperature dependence of resistivity was observed indicative of a Fermi liquid behavior. The temperature dependence of the field-cooling (FC) and zero-field-cooling (ZFC) magnetization and time decay of thermoremanent magnetization indicate the spin-glass-like behavior in InNM{sub 3} (M=Ni, Co). The freezing temperatures for this behavior, T{sub f}, are about 300 K for InNNi{sub 3} and 10 K for InNCo{sub 3}, respectively. - Graphical abstract: Two ternary nitrides InNM{sub 3} (M=Ni, Co) were synthesized by solid-gas reactions of metal powders with NH{sub 3}. Both InNNi{sub 3} and InNCo{sub 3} adopt the antiperovskite crystal structure, and measurements of magnetization indicate that they have spin-glass-like properties.

36 MATERIALS SCIENCE↗

A tantalum strength model using a multiscale approach: version 2

A continuum strength model for tantalum was developed in 2007 using a multiscale approach. This was our first attempt at connecting simulation results from atomistic to continuum length scales, and much was learned that we were not able to incorporate into the model at that time. The tantalum model described in this report represents a second cut at pulling together multiscale simulation results into a continuum model. Insight gained in creating previous multiscale models for tantalum and vanadium was used to guide the model construction and functional relations for the present model. While the basic approach follows that of the vanadium model, there are significant departures. Some of the recommendations from the vanadium report were followed, but not all. Results from several new analysis techniques have not yet been incorporated due to technical difficulties. Molecular dynamics simulations of single dislocation motion at several temperatures suggested that the thermal activation barrier was temperature dependent. This dependency required additional temperature functions be included within the assumed Arrhenius relation. The combination of temperature dependent functions created a complex model with a non unique parameterization and extra model constants. The added complexity had no tangible benefits. The recommendation was to abandon the strict Arrhenius form and create a simpler curve fit to the molecular dynamics data for shear stress versus dislocation velocity. Functions relating dislocation velocity and applied shear stress were constructed vor vanadium for both edge and screw dislocations. However, an attempt to formulate a robust continuum constitutive model for vanadium using both dislocation populations was unsuccessful; the level of coupling achieved was inadequate to constrain the dislocation evolution properly. Since the behavior of BCC materials is typically assumed to be dominated by screw dislocations, the constitutive relations were ultimately built using only the screw relations. In light of this, the screw dislocation mobility relation is chosen as the starting point for the present tantalum model. Edge dislocations are not included explicitly in the current model. A significant change from the previous models is in the functional dependence of the dislocation evolution equations. The prior multiscale models assumed that the dislocation evolution rate depended on stress as well dislocation velocity. This crated an implicit dependence on the kinetic relation and required an iterative solution for the dislocation density. In the present model the integration scheme is simplified by casting the dislocation evolution terms of strain rate and current dislocation density. The final notable change was in the transition relation from the thermally activated regime to phonon drag. Historically, and in the prior models, this transition had been through a harmonic average on the strain rates making it impossible to determine the stress directly when given the plastic strain rate. After considering alternative transition relations, it was determined that an equally suitable fit to the molecular dynamics simulation data in the transition region could be constructed by averaging stresses rather than strain rates. The end result of these enhancements is a simpler (fewer parameters) and more straight forward model formulation where the material strength can be evaluated directly when given the plastic strain rate, temperature, pressure and the dislocation density at the beginning of the time step. This greatly improves the computational efficiency and robustness over the prior models where additional iteration loops were required.

36 MATERIALS SCIENCE↗

DAC Measurement of High-Pressure Yield Strength of Vanadium using In-Situ Thickness Determination

The pressure-dependence of the quasi-static yield strength of vanadium in polycrystalline foils and powders has been measured up to 80 GPa at room temperature using an implementation of a non-hydrostatic diamond anvil cell technique [C. Meade and R. Jeanloz, J. Geophys. Res. 93, 3261 (1988)]. A new feature of this work is the use of an in-situ determination of the sample thickness. Following an initial increase in the strength with pressure, a decrease in the strength of vanadium was observed beginning at 40-50 GPa. We have measured the yield strength of vanadium up to 80 GPa under nonhydrostatic conditions. In this study, we used x-ray diffraction and absorption techniques to make in-situ measurements of the pressure gradient and the sample thickness. These measurements were used to evaluate the pressure-dependence of the material strength. We observed a decease in the yield strength of vanadium over the pressure range of 40-50 GPa. We propose that this change in the yieldstrength pressure-dependence is an indicator of the phase transition from bcc to rhombohedral.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Numerical study on convection diffusion for gasification agent in underground coal gasification (UCG). Part II: determination of model parameters and results analysis

The determination methods of the major model parameters are explained in this article, and the upstream weighted multi-cell balance method is adopted to solve the numerical models established. The author also analyzes and discusses the simulated calculation results, which show that, except for very few points in the loosening zone, where the relative calculation error is comparatively high resulting from the low oxygen concentration, the relative calculation error of other points falls between 8% and 19%. Therefore, the calculation value and the experiment value take on a good conformity. The simulated results indicate that the calculation value of the oxygen concentration is a little bit lower than the experiment one. On top of that, with the prolonging of gasification time, in a high temperature zone the change gradient of oxygen concentration for experimental value is bigger than that of the calculation value. The oxygen concentration is in direct proportion to its distance from the flame working face, i.e., the longer its distance is, the higher the oxygen concentration is; otherwise, the lower the oxygen concentration is.

01 COAL, LIGNITE, AND PEAT↗

Underground coal gasification field experiment in the high-dipping coal seams

In this article the experimental conditions and process of the underground gasification in the Woniushan Mine, Xuzhou, Jiangsu Province are introduced, and the experimental results are analyzed. By adopting the new method of long-channel, big-section, and two-stage underground coal gasification, the daily gas production reaches about 36,000 m{sup 3}, with the maximum output of 103,700 m{sup 3}. The daily average heating value of air gas is 5.04 MJ/m{sup 3}, with 13.57 MJ/m{sup 3} for water gas. In combustible compositions of water gas, H{sub 2} contents stand at over 50%, with both CO and CH{sub 4} contents over 6%. Experimental results show that the counter gasification can form new temperature conditions and increase the gasification efficiency of coal seams.

01 COAL, LIGNITE, AND PEAT↗

Underground coal gasification using oxygen and steam

In this paper, through model experiment of the underground coal gasification, the effects of pure oxygen gasification, oxygen-steam gasification, and moving-point gasification methods on the underground gasification process and gas quality were studied. Experiments showed that H{sub 2} and CO volume fraction in product gas during the pure oxygen gasification was 23.63-30.24% and 35.22-46.32%, respectively, with the gas heating value exceeding 11.00 MJ/m{sup 3}; under the oxygen-steam gasification, when the steam/oxygen ratio stood at 2: 1, gas compositions remained virtually stable and CO + H{sub 2} was basically between 61.66 and 71.29%. Moving-point gasification could effectively improve the changes in the cavity in the coal seams or the effects of roof inbreak on gas quality; the ratio of gas flowing quantity to oxygen supplying quantity was between 3.1:1 and 3.5:1 and took on the linear changes; on the basis of the test data, the reasons for gas quality changes under different gasification conditions were analyzed.

01 COAL, LIGNITE, AND PEAT↗

Numerical study on convection diffusion for gasification agent in underground coal gasification. Part I: establishment of mathematical models and solving method

The aim of this article is to discuss the distribution law of the gasification agent concentration in a deep-going way during underground coal gasification and the new method of solving the problem for the convection diffusion of the gas. In this paper, the basic features of convection diffusion for the gas produced in underground coal gasification are studied. On the basis of the model experiment, through the analysis of the distribution and patterns of variation for the fluid concentration field in the process of the combustion and gasification of the coal seams within the gasifier, the 3-D non-linear unstable mathematical models on the convection diffusion for oxygen are established. In order to curb such pseudo-physical effects as numerical oscillation and surfeit which frequently occurred in the solution of the complex mathematical models, the novel finite unit algorithm, the upstream weighted multi-cell balance method is advanced in this article, and its main derivation process is introduced.

01 COAL, LIGNITE, AND PEAT↗