Engineering Papers⌕ Search

Engineering topics

Yang, Bin

Publications and source records attributed to Yang, Bin.

501 records · Page 28
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Flowthrough Pretreatment of Softwood under Water-only and Alkali Conditions

Flowthrough pretreatment provides valuable insight in the fundamentals of deconstruction of plant biomass. In this study, the potential softwood degradation pathways under water-only and alkali conditions were determined by elucidating the deconstructed biomass-derived products at 0-270 °C for 2-10 min at a flow rate of 25 mL/min with water-only or alkaline at initial pH of 8, 9, 11, and 12, respectively. Results indicated that the initial pH value was a convenient indicator along with the severity parameter to control biomass degradation through the non-oxidative (pH<9) and oxidative (pH=9) pathways. Up to 100 % of hemi-sugars, 90 % of cellulose, and 70 % of lignin were derived from softwood under non-oxidative conditions at severity parameter LogR0 around 5.5, respectively. On the contrary, at pH 12, the oxidative degradation resulted in pretreated hydrolysate rich in monomeric and oligomeric phenolic products as well as glycolic acid, acetic acid, and formic acid from carbohydrates. The two dimensional 1H-13C heteronuclear single quantum coherence (HSQC) nuclear magnetic resonance (NMR) analysis revealed that non-oxidative degradation at initial pH values lower than 9 mainly cleaved ß-O-4, all of the ß-ß, and ß-5/a-O-4 linkages, whereas substantial aromatic ring structures with limited ß-O-4 structures remaining at pH 12 through oxidative degradation.

Zhang, Libing↗
DOE OSTI2020

High-throughput synthesis and corrosion behavior of sputter-deposited nanocrystalline Al x (CoCrFeNi) 100-x combinatorial high-entropy alloys

High-entropy alloys (HEAs) are inherently complex and potentially span a vast composition space, making their research and discovery challenging. In the present study, high-throughput synthesis of an Al x (CoCrFeNi) 100-x combinatorial material library covering x = 4.5–40 atomic percent Al is achieved, using magnetron cosputtering. The effects of Al on the microstructure and corrosion behavior are investigated. With the increased amount of Al, crystal-structures of thin films transform from face-centered cubic (FCC) to body-centered cubic (BCC). Both the FCC and BCC thin films demonstrate a uniform elemental distribution. Corrosion characteristics of combinatorial samples immersed in the 3.5 wt% (wt%) NaCl solution are evaluated via electrochemical tests. Complementary X-ray photoelectron spectroscopy analysis reveals the compositional variation of passivated films formed on the sample surface after immersion. The results show that the Al x (CoCrFeNi) 100-x HEA thin films possess outstanding corrosion-resistant properties, but the resistance diminishes with the increasing Al content. The decreased corrosion resistance is revealed to be directly related to the constituents of passivated films.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Non-invasive (non-contact) measurements of human thermal physiology signals and thermal comfort/discomfort poses -A review

Heating, ventilation and air-conditioning (HVAC) systems have been adopted to create comfortable, healthy and safe indoor environments. In the control loop, the technical feature of the human demand-oriented supply can help operate HVAC effectively. Among many technical options, real time monitoring based on feedback signals from end users has been frequently reported as a critical technology to confirm optimizing building performance. Recent studies have incorporated human thermal physiology signals and thermal comfort/discomfort status as real-time feedback signals. A series of human subject experiments used to be conducted by primarily adopting subjective questionnaire surveys in a lab-setting study, which is limited in the application for reality. With the help of advanced technologies, physiological signals have been detected, measured and processed by using multiple technical formats, such as wearable sensors. Nevertheless, they mostly require physical contacts with the skin surface in spite of the small physical dimension and compatibility with other wearable accessories, such as goggles, and intelligent bracelets. Most recently, a low cost small infrared camera has been adopted for monitoring human facial images, which could detect the facial skin temperature and blood perfusion in a contactless way. Also, according to latest pilot studies, a conventional digital camera can generate infrared images with the help of new methods, such as the Euler video magnification technology. Human thermal comfort/discomfort poses can also be detected by video methods without contacting human bodies and be analyzed by the skeleton keypoints model. Here, new sensing technologies were summarized, their cons and pros were discussed, and extended applications for the demand-oriented ventilation were also reviewed as potential development and applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

In-situ visualization of corrosion behavior of Al CoCrFeNi high-entropy alloys during electrochemical polarization

In this study, the corrosion behavior of the Al x CoCrFeNi (x = 0.3, 0.5, 0.7) high-entropy alloys (HEAs) is investigated by an in-situ visualization system. Surface morphology changes on both micro-spatial and temporal scales are monitored in the 3.5 wt% NaCl solution during the potentiodynamic polarization. The microstructures of the Al x CoCrFeNi HEAs are characterized by SEM, EBSD, and EDS. The results show that the microstructure evolves from singe face-centered cubic (FCC) phase to multi-phases by increasing the Al content. The in-situ observations directly reveal the different localized corrosion processes in the AlxCoCrFeNi HEAs. In the single FCC phase Al 0.3 CoCrFeNi HEA, localized corrosion shows in the form of pitting. In the Al 0.5 CoCrFeNi and Al 0.7 CoCrFeNi alloys, which possess FCC and body-centered cubic (BCC) phases, the localized corrosion initiates and propagates in the Cr-depleted BCC phase. In addition, the in-situ visualization uncovers the evolution of current serration, which represents the propagation and repassivation of metastable pit during the polarization. The frequent occurrence of metastable pits indicates distinct repassivation ability of the Al 0.3 CoCrFeNi HEA.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A radiative transfer model for solar induced fluorescence using spectral invariants theory

Solar Induced chlorophyll Fluorescence (SIF) shows promise as an approach for estimating gross primary production (GPP) remotely. However, sun-target-sensor geometry and within-canopy absorption of SIF can alter the relationship between measured SIF and GPP, because sensors can only retrieve some unknown fraction of the total emitted SIF. Radiative transfer models that allow for variation in canopy structure and sensor angles are therefore needed to properly interpret SIF measurements. Spectral invariants allow decoupling of the wavelength-independent canopy structure and the wavelength-dependent leaf and soil spectrum in the radiative transfer process. Here we develop a simple analytical Fluorescence Radiative Transfer model based on Escape and Recollision probability (FluorRTER) to investigate the impact of canopy structure and sun-target-sensor geometry on SIF emissions. SIF simulations using the FluorRTER model agreed well the one-dimensional Soil-Canopy Observation of Photochemistry and Energy balance (SCOPE) model and the three-dimensional Fluorescence model with Weighted Photon Spread (FluorWPS) model. The fractional vegetation cover (FVC) and clumping effect have a large influence the SIF emission of 3D discontinuous canopies. For a moderate solar zenith angle (30°) and a clumped canopy (FVC?=?0.6), the difference between the directional observed SIF of a 3D discontinuous canopy and a 1D homogeneous canopy was as large as 43.2% and 38.4% for Photosystem I?+?II fluorescence at 685?nm and at 740?nm, respectively. By bridging the gap between observed SIF and total emitted SIF over 3D heterogeneous vegetation canopies, the FluorRTER model can assist with the angular normalization of SIF measurements and enable the more robust interpretation of how variations in SIF from directional and hemispherical in-situ, airborne and satellite observations relate to leaf and whole-canopy physiological processes.

Zeng, Yelu↗
DOE OSTI2020

Electron-Beam-Related Studies of Halide Perovskites: Challenges and Opportunities

Electron beam microscopy and related characterization techniques play an important role in revealing the microstructural, morphological, physical, and chemical information of halide perovskites and their impact on associated optoelectronic devices. However, electron beam irradiation usually causes damage to these beam-sensitive materials, negatively impacting their device performance, and complicating this interpretation. Here, the electron microscopy and spectroscopy techniques are reviewed that are crucial for the understanding of the crystallization and microstructure of halide perovskites. In addition, special attention is paid to assessing and mitigating the electron beam-induced damage caused by these techniques. Since the halide perovskites are fragile, a protocol involving delicate control of both electron beam dose and dose rate, coupled with careful data analysis, is key to enable the acquisition of reliable structural and compositional information such as atomic-resolution images, chemical elemental mapping and electron diffraction patterns. Limiting the electron beam dose is critical parameter enabling the characterization of various halide perovskites. Novel methods to unveil the mechanisms of device operation, including charge carrier generation, diffusion, and extraction are presented in scanning electron microscopy studies combined with electron-beam-induced current and cathodoluminescence mapping. Future opportunities for electron-beam-related characterizations of halide perovskites are also discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Lignin-derived electrochemical energy materials and systems

Electrochemical energy storage systems such as supercapacitors, rechargeable batteries and fuel cells have been proven the most effective technologies for energy conversion, storage, and management at different scales. Although a large number of electrochemical energy technologies have been developed in the past and they will continue to be optimized in terms of cost, lifetime, and performance, there is a substantial growing demand for advanced electrochemical energy systems. To deploy these advanced systems, the electrode and electrolyte materials with higher performance, longer life, and lower cost, must be developed. Lignin is the second most abundant natural polymer after cellulose, a byproduct from emerging cellulosic biorefineries, and a waste product from pulp and paper industries. Numerous researches have successfully demonstrated that lignin from different sources can be used as precursors or feedstocks for preparing high-performance electrochemical energy materials and components such as electrodes, electrolytes, membrane separators, and additives. Moreover, techno-economic analyses indicate that it is possible to prepare cost-effective carbons from lignin at engineering scales, compared to current carbon products. These facts suggest that scalable conversion of lignin into high-value energy materials will offer a promising pathway to not only promote the utilization and valorization of lignin but also boost the development of the advanced electrochemical energy systems. This review presents state of the arts of renewable energy materials derived from various lignin and their applications in electrochemical energy systems with emphasis on supercapacitors, rechargeable batteries, and fuel cells. Meanwhile, this article also aims to carve out the critical barriers for lignin-derived high-performance materials for energy applications, intending to identify viable approaches for synthesis of sustainable new energy materials.

09 BIOMASS FUELS↗
DOE OSTI2020

Study on the High-Pressure Behavior of Goethite up to 32 GPa Using X-Ray Diffraction, Raman, and Electrical Impedance Spectroscopy

Goethite is a major iron-bearing sedimentary mineral on Earth. In this study, we conducted in situ high-pressure x-ray diffraction, Raman, and electrical impedance spectroscopy measurements of goethite using a diamond anvil cell (DAC) at room temperature and high pressures up to 32 GPa. We observed feature changes in both the Raman spectra and electrical resistance at about 5 and 11 GPa. However, the x-ray diffraction patterns show no structural phase transition in the entire pressure range of the study. The derived pressure-volume (P-V) data show a smooth compression curve with no clear evidence of any second-order phase transition. Fitting the volumetric data to the second-order Birch–Murnaghan equation of state yields V 0 = 138.9 ± 0.5 Å 3 and K 0 = 126 ± 5 GPa.

58 GEOSCIENCES↗
DOE OSTI2020

Influence of ozone addition on the low-temperature oxidation of dimethyl ether in a jet-stirred reactor

The influence of ozone addition on the low-temperature oxidation of dimethyl ether (DME) was investigated experimentally in an atmospheric-pressure jet-stirred reactor, over the temperature range of 400–800 K. Detailed speciation information was obtained by employing synchrotron vacuum ultraviolet photoionization mass spectrometry. Experimental results revealed that the ozone addition had a positive influence on the production of the highly reactive intermediates. Moreover, the low-temperature reactivity of DME was significantly enhanced, which resulted in the broadening of the temperature window of fuel consumption and intermediates formation at lower temperatures. Therefore, novel experimental data of the low temperature regime (400–500 K) could be obtained. The data set of this special temperature regime yielded insights into the DME low-temperature kinetics, which were further supported with modeling analysis based on two existing DME models (Metcalfe et al., 2013; Wang et al., 2015) combined with an ozone sub-mechanism (Zhao et al., 2016). The analysis showed that temperature-sensitive reactions such as the second oxygen channel could be nearly “frozen” at this low temperature (T < 440 K). Furthermore, the production of some intermediates was found to be strongly governed by reaction pairs, such as CH 3 OCH 2 + O 2 = CH 3 OCH 2 O 2 and CH 3 OCH 2 + O 2 = 2 CH 2 O + OH for the CH 2 O formation. This finding could be useful for examining branching ratios in both models, and the analysis suggested the further modification of the branching ratios for the oxygen addition to CH 3 OCH 2 O 2 pathways and the CH 3 OCH 2 O 2 self-reactions were required. Finally, the influences of the O 3 addition in the sensitive reactions of the fuel initial low-temperature oxidation were investigated in this work. It was interesting to note that O 3 addition could change the dominating reactions in the initial low-temperature oxidation, by the addition of some O 3 -related pathways with relatively high sensitivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2018

Implications of Whole-Disc DSCOVR EPIC Spectral Observations for Estimating Earth's Spectral Reflectivity Based on Low-Earth-Orbiting and Geostationary Observations

Earth's reflectivity is among the key parameters of climate research. National Aeronautics and Space Administration (NASA)'s Earth Polychromatic Imaging Camera (EPIC) onboard National Oceanic and Atmospheric Administration (NOAA)'s Deep Space Climate Observatory (DSCOVR) spacecraft provides spectral reflectance of the entire sunlit Earth in the near backscattering direction every 65 to 110 min. Unlike EPIC, sensors onboard the Earth Orbiting Satellites (EOS) sample reflectance over swaths at a specific local solar time (LST) or over a fixed area. Such intrinsic sampling limits result in an apparent Earth's reflectivity. We generated spectral reflectance over sampling areas using EPIC data. The difference between the EPIC and EOS estimates is an uncertainty in Earth's reflectivity. We developed an Earth Reflector Type Index (ERTI) to discriminate between major Earth atmosphere components: clouds, cloud-free ocean, bare and vegetated land. Temporal variations in Earth's reflectivity are mostly determined by clouds. The sampling area of EOS sensors may not be sufficient to represent cloud variability, resulting in biased estimates. Taking EPIC reflectivity as a reference, low-earth-orbiting-measurements at the sensor-specific LST tend to overestimate EPIC values by 0.8% to 8%. Biases in geostationary orbiting approximations due to a limited sampling area are between −0.7% and 12%. Analyses of ERTI-based Earth component reflectivity indicate that the disagreement between EPIC and EOS estimates depends on the sampling area, observation time and vary between −10% and 23%.

DSCOVR↗