Engineering Papers⌕ Search

Engineering topics

Xu, Haixuan

Publications and source records attributed to Xu, Haixuan.

At least 19 records

Impurity-enhanced core valence luminescence via Zn-doping in cesium magnesium chlorides

Scintillators with faster timing capabilities are currently in high demand for use in radiation detection systems in the fields of nuclear and medical physics. The limited number of suitable materials that meet the performance criteria of next generation detection systems presents an opportunity for discovery of new fast scintillator materials. In this work, the effects of doping several ultrafast core-valence luminescent (CVL) scintillators with divalent Zn is explored. Three compounds are investigated – CsMgCl 3 , Cs 2 MgCl 4 , and Cs 3 MgCl 5 – and single crystals of each doped with 5 mol% Zn are grown via the Bridgman method. Additionally, mixing across the full range of concentrations (from 0 % to 100 % Zn) is explored in the Cs 2 Mg 1-x Zn x Cl 4 and Cs 3 Mg 1-x Zn x Cl 5 systems. For low concentrations of Zn, light yields of all three compounds are enhanced (by up to ~60 %) compared to the pure crystals, achieving what we believe to be the brightest known CVL, CsMgCl 3 :Zn 5 % (3400 ± 170 ph/MeV light yield). More importantly, Zn doping does not affect the ultrafast timing properties, with each composition maintaining a single-component decay time around 1–3 ns. A sub-100 ps coincidence time resolution (CTR) is also achieved with CsMgCl 3 :Zn 5 %. The results of this work reveal a new avenue towards obtaining brighter CVL materials, which could open up possibilities for more advanced ultrafast scintillators to be discovered moving forward.

36 MATERIALS SCIENCE↗

New Ultrafast Scintillators with Core Valence Luminescence: Cs 2 MgCl 4 and Cs 3 MgCl 5

Future experiments in high energy physics and medical imaging require radiation detectors having properties which are not presently available. The main limitations arise from lack of suitable scintillation crystals. This dilemma prompts the need for research leading to the discovery of new fast and bright scintillator materials that combine unique properties to fulfil modern experiment requirements without compromises. In this work, single crystals of Cs 2 MgCl 4 and Cs 3 MgCl 5 up to 12 mm in diameter are grown via the vertical Bridgman method. Scintillation properties are reported for the first time, and core valence luminescence is observed for both compounds. X-ray excited radioluminescence emission of Cs 2 MgCl 4 is centered at 295 nm, with a scintillation decay time of 2.25 ± 0.05 ns and relatively high core-valence light yield of 2,200 ± 110 ph/MeV. Cs 3 MgCl 5 has two main emission peaks centered at 242 nm and 302 nm, decay time of 1.46 ± 0.05 ns, and light yield of 1,340 ± 70 ph/MeV. The better coincidence time resolution (CTR) is obtained with Cs 2 MgCl 4 , which is measured to be 129 ± 4 ps FWHM. Density functional theory (DFT) calculations are also performed and provide supporting evidence that the observed scintillation originates from core valence luminescence. Furthermore, the combination of speed and brightness of these new scintillators could be useful for fast timing applications in which moderately dense materials are required.

36 MATERIALS SCIENCE↗

Enhanced Ferromagnetism in Atomically Thin Oxides Achieved by Interfacial Reconstruction

Discoveries of ferromagnetic materials with ultrathin thickness are of great importance for both fundamental science and technological applications. Transition metal oxides (TMOs) provide promising candidates in the context of next‐generation spintronics, despite the severe decay of ferromagnetism as the thickness reduces to the nanometer regime. Here, in this work, an efficient strategy to eliminate the magnetic dead layer in atomically thin oxides is presented, by using the epitaxial interface of 3 d and 5 d oxide monolayers that reconciles both strong exchange interaction and large uniaxial magnetic anisotropy. Combining multiple experimental methods, a ferromagnetic transition in an ultrathin oxide heterostructure comprised of only one La 0.2 Sr 0.8 MnO 3 monolayer sandwiched by SrIrO 3 monolayer (total thickness of three unit‐cells) is unambiguously demonstrated. Remarkably, a largely enhanced saturation magnetization (2 µ B Mn −1 ) and Curie temperature (80 K) are observed for the single manganite monolayer, as compared to previously reported ferromagnetic monolayer oxides. The results demonstrate a general strategy for creating robust ferromagnetism in ultrathin TMOs, potentially enabling novel oxide spin‐orbitronic devices.

2D ferromagnetism↗

Saddle point search with dynamic active volume

Sampling potential energy surface (PES) is critical for many problems in materials science, chemistry, physics, and biology and requires highly efficient saddle point searches (SPS). In the study, we introduce the concept of dynamic active volume (DAV) in addition to the active volume in self-evolving atomistic kinetic Monte Carlo (SEAKMC). The DAV method has further reduced the dimensionality of the PES at the elevation stage of a SPS. At the subsequent converging stage, the dynamic boundary in DAV is lifted to allow the system to converge to the right location of a saddle point. Coupled with the dimer method, the DAV method not only significantly reduces the time cost for a given search attempt, but also dramatically increases the probability of finding relevant saddle points for PES sampling. Further, a Python software package within the framework SEAKMC (SEAKMC_py) with the DAV method has been developed.

36 MATERIALS SCIENCE↗

Deciphering the multiple deformation mechanisms responsible for sustained work hardening in a FeCrCoNi medium entropy alloy

Two important and desirable properties of materials for most structural applications are high tensile strength and ductility, which typically require high work hardening to delay necking. Here, in this work, we designed and tensile tested a face-centered cubic (fcc) Fe-Cr-Co-Ni medium-entropy alloy in which multiple deformation mechanisms are triggered during tensile loading at different temperatures to induce sustained work hardening. Our strategy involved control of the relative stabilities of the fcc, hcp (hexagonal close-packed), and bcc (body-centered cubic) phases in this quaternary system via high-throughput thermodynamic calculations. This alloy not only exhibits extensive deformation-induced nanotwinning at room temperature, but also displays a two-step sequential phase transformation [γ (fcc) → ε (hcp) martensite → α’ (bcc) martensite] at 77 K, which contrasts with the single-step phase transformation [γ → ε martensite] observed in many other fcc high/medium entropy alloys with a low stacking fault energy. The sequence of phase transformation at 77K was supported by first-principles density functional theory calculations. This work provides new templates for the design of alloys capable of multiple deformation mechanisms for sustained work hardening.

36 MATERIALS SCIENCE↗

Discovery of multimechanisms of screw dislocation interaction in bcc iron from open-ended saddle point searches

Dislocation motion and interactions determine mechanical properties in body-centered cubic (bcc) metallic materials. However, studying mechanisms for the screw dislocation interaction is fundamentally challenging since many underlying processes involve mesotimescales and atomistic resolution, currently inaccessible by either experimental techniques or continuum theoretical methods. Here, in this paper, we develop a computational capability based on self-evolving atomistic kinetic Monte Carlo (SEAKMC) to sample the critical events and saddle point energies related to screw dislocations and their junctions. The method is first validated by calculating the stress dependence of Peierls barriers and formation energies of kink pairs and cross-slip kink pairs on a single screw dislocation in bcc iron. Then the method is applied to a binary junction of a pair of intersecting screw dislocations, the structure of which is crucial for low-temperature plastic deformation. We identify three important mechanisms: coplanar cross-slipping, jog-pinning, and a previously unknown unzipping mechanism during the evolution of the binary junction. The mechanisms are then further validated using classical molecular dynamics simulations. The computational capability developed in this paper provides an effective tool to evaluate screw dislocation related thermally activated events in complex stress conditions. The mechanisms discovered in this paper provide critical insights into temperature dependence of the anomalous slip, a breakdown of the Schmidt law, during the plastic deformation in bcc iron and can be generalized to other bcc metals.

36 MATERIALS SCIENCE↗

Using lifetime of point defects for dislocation bias in bcc Fe

The interaction between dislocations and point defects is key to deformation processes and microstructural evolution of structural materials. In this work, we compute the lifetime of point defects to describe their interaction with dislocations. This approach can accurately account for the effects of the dislocation core and anisotropic defect dynamics to accumulatively determine the capture efficiency, sink strength, and dislocation bias at different temperatures and dislocation densities. Particularly, the absorption of point defects by straight screw and edge dislocations in a model bcc iron system is studied. The maximum swelling rates based on the obtained bias factors are in close agreement with a variety of experimental measurements, including both neutron and ion-irradiation data, especially when considering the survival fraction for point defects from displacement cascades. Further, this approach applies to many other processes and sinks, such as dislocation loops and interfaces, providing a powerful means to develop fundamental insights critical for improving radiation resistance and mechanical properties of structural materials through controlling defect interaction and evolution.

36 MATERIALS SCIENCE↗

Saddle point sampling using scaled normal coordinates

The sampling of saddle points (SPs) on a potential energy surface (PES) is critical for describing the dynamics and transport properties of materials. In this paper we propose a saddle point search (SPS) method that enables efficient sampling of practically meaningful SPs around a local minimum by converting the PES to the scaled normal coordinates (SNCs), together with the dimer method. We find that the pathway leading to a SP using SNCs is highly efficient and is independent of the system size. This results in the significantly increased SPS efficiency and the enhanced possibility of a complete catalog of the SPs. In addition, we perform SPSs using the SNCs for the diffusion of a vacancy and a dumbbell in body-centered cubic Fe and demonstrate (1) the required number of system force evaluations for a SPS decreases by at least an order of magnitude, (2) the effects of the system size on the number of force evaluations are greatly decreased, and (3) the effects of the number of atoms involved in the SPS on the probability of finding practically meaningful SPs is mostly eliminated. We also discuss the computational cost of introducing the SNCs. It should be highlighted that the SNCs could also be applied to other minimum-mode following methods, demonstrating the general versatility of the proposed method.

36 MATERIALS SCIENCE↗

Capture efficiency and bias from the defect dynamics near grain boundaries in BCC Fe using mesoscale simulations

The capture efficiency describes the capability of a sink, such as a grain boundary (GB), dislocation, and void, to absorb point defects (PDs). The bias defines the difference in capture efficiency between the absorption of a vacancy and dumbbell at a sink. Complete kinetic information on PDs, including diffusion barriers and diffusion orientations, as well as accurate saddle points, are needed to determine the capture efficiency and bias at a sink accurately, which is computationally demanding. Here, in the present study, the Self-Evolving Atomistic Kinetic Monte Carlo (SEAKMC) method was used to investigate the defect dynamics of PDs near different types of grain boundaries (GBs) (with both $\langle$100$\rangle$ and $\langle$110$\rangle$ families) accurately in body-centered cubic (BCC) iron (Fe). The capture efficiency, sink strength, and bias factor of different types of GBs were determined in Fe, which, different from traditional rate theory estimation, showed a distinct capture efficiency, sink strength, and bias in different GBs. The results demonstrate a strong positive correlation between the capture efficiency and the GB strain width, instead of the GB misorientation, GB energy, or GB-PD binding energy, which have been investigated previously. This work provides valuable insight into the radiation-induced microstructural evolution of GBs.

36 MATERIALS SCIENCE↗

Atomistic modeling of meso -timescale processes with $\mathrm{SEAKMC}$: A perspective and recent developments

On-the-fly kinetic Monte Carlo (kMC) methods have recently garnered significant attentions after successful applications to various atomic-scale problems using a timescale outside the reach of classical molecular dynamics. These methods play a critical role in modeling atomistic meso-timescale processes, and it is therefore essential to further improve their capabilities. In this report we review one of the on-the-fly kMC methods, Self-Evolving Atomistic kinetic Monte Carlo (SEAKMC) and propose two schemes that considerably enhance the efficiency of saddle point searches (SPSs) during the simulations. The performance of these schemes is tested using the diffusion of point defects in bcc Fe. In addition, we discuss approaches to significantly mitigate limitations of these schemes, which further improves their efficiencies. Importantly, these schemes improve the SPS efficiency not only for SEAKMC but also for other on-the-fly kMC methods, broadening the applications of on-the-fly kMC simulations to complex meso-timescale problems.

36 MATERIALS SCIENCE↗

Migration energy barriers and diffusion anisotropy of point defects on tungsten surfaces

We report tungsten is one of the most promising candidates for plasma-facing materials in future fusion devices, owing to its high performance under extreme irradiation conditions. However, irradiation-induced surface morphology varies significantly, depending on the irradiation type, fluence, and flux. Therefore, it is critical to examine the dynamics of point defects on tungsten (W) surfaces to understand how irradiation affects surface morphology. In this study, we employ the Self-Evolving Atomistic Kinetic Monte Carlo (SEAKMC) method to search for potential migration paths of point defects on W (1 0 0), (1 1 0) and (1 1 1) surfaces. The first-principles calculations are then used to accurately determine the migration energy barriers. The obtained paths and barriers are incorporated into a kinetic Monte Carlo (KMC) model to determine trajectories and diffusivities, which are described by diffusion tensors to demonstrate their anisotropic features. Multiple diffusion mechanisms have been identified on different surfaces, with various anisotropy factors. Particularly, point defects on the W (1 1 0) surface have the highest diffusivities, with anisotropy factors independent of temperatures. In comparison, the anisotropy of the W (1 0 0) surface decreases as temperature increases, while the W (1 1 1) surface is isotropic for point defects. This study provides insights into defect transport properties on different surfaces, which are essential for understanding the early stages of irradiation-induced microstructural evolutions and surface morphology of tungsten.

36 MATERIALS SCIENCE↗

Strain-Modulated Slater-Mott Crossover of Pseudospin-Half Square-Lattice in ( SrIrO 3 ) 1 / ( SrTiO 3 ) 1 Superlattices

Here, we report on the epitaxial strain-driven electronic and antiferromagnetic modulations of a pseudospin-half square lattice realized in superlattices of (SrIrO 3 ) 1 /(SrTiO 3 )1. With increasing compressive strain, we find the low-temperature insulating behavior to be strongly suppressed with a corresponding systematic reduction of both the Néel temperature and the staggered moment. However, despite such a suppression, the system remains weakly insulating above the Néel transition. The emergence of metallicity is observed under large compressive strain but only at temperature far above the Néel transition. These behaviors are characteristics of the Slater-Mott crossover regime, providing a unique experimental model system of the spin-half Hubbard Hamiltonian with a tunable intermediate coupling strength.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Emergent electric field control of phase transformation in oxide superlattices

Electric fields can transform materials with respect to their structure and properties, enabling various applications ranging from batteries to spintronics. Recently electrolytic gating, which can generate large electric fields and voltage-driven ion transfer, has been identified as a powerful means to achieve electric-field-controlled phase transformations. The class of transition metal oxides provide many potential candidates that present a strong response under electrolytic gating. However, very few show a reversible structural transformation at room-temperature. Here, we report the realization of a digitally synthesized transition metal oxide that shows a reversible, electric-field-controlled transformation between distinct crystalline phases at room-temperature. In superlattices comprised of alternating one-unit-cell of SrIrO 3 and La 0.2 Sr 0.8 MnO 3 , we find a reversible phase transformation with a 7% lattice change and dramatic modulation in chemical, electronic, magnetic and optical properties, mediated by the reversible transfer of oxygen and hydrogen ions. Strikingly, this phase transformation is absent in the constituent oxides, solid solutions and larger period superlattices. Our findings open up this class of materials for voltage-controlled functionality.

36 MATERIALS SCIENCE↗

Chemical Trend of Transition-Metal Doping in W Se 2

Transition-metal dichalcogenides (TMDs) are promising nanoscale materials with a wide range of applications. Chemical doping is a powerful tool for tailoring the physical and chemical properties of TMDs for targeted functionalities. As one of the most important TMDs, WSe 2 has great potential for applications in field effect transistor and complementary metal oxide semiconductor technologies for its bipolar dopability. Yet, precise control over the type and density of free carriers remains challenging. First-principles calculations are performed to study intrinsic defects and transition-metal (TM) dopants in WSe 2 . Our findings demonstrate that TM doping can effectively control the Fermi level in WSe 2 with no significant compensation by intrinsic defects. Nb and Ta are effective p-type dopants capable of generating a high free hole density in WSe 2 . While n-type doping is possible by Re (under the Se-rich condition) and Cu (under the W-rich condition), the doping efficiency is reduced due to the lower attainable dopant concentration and higher ionization energies. The chemical trend in the attainable concentration of various substitutional TM dopants in WSe 2 is largely determined by the competition between the dopant incorporation in WSe 2 and the formation of the secondary phase TMSe 2 . Such a competition is strongly affected by the different crystal environments of the TM ion in TMSe 2 and WSe 2 , which determine the crystal field splitting and electron filling of TM d levels and consequently the formation energy of the TM dopant.

36 MATERIALS SCIENCE↗

Interactions between displacement cascade and dislocation and their influences on Peierls stress in Fe-20Cr-25Ni alloys

The interactions between dislocations and displacement cascades are investigated using molecular dynamics simulations. The primary knock-on atoms (PKAs) are placed at different distances to edge and screw dislocation lines. Specifically, an fcc Fe-20Cr-25Ni system is studied; the alloy is the based alloy for Alloy 709. The number of defects is calculated using Wigner-Seitz analysis in order to illustrate the effect of dislocations on cascades. The displacement cascades in systems containing dislocations tend to generate more total defects compared with bulk systems, but eventually lead to less surviving defects in the materials matrix due to interactions with dislocations. The changes in atomic structures of the dislocations after interacting with cascades are analyzed to understand how the primary damage affects dislocations. The displacement cascade potentially causes dislocation climb in edge dislocations and cross-slip in screw dislocations, which could serve as additional mechanisms contributing to the radiation-induced hardening (RIH) compared with conventional RIH models. To reveal this, Peierls stresses are calculated before and after cascades using molecular static simulations. This study provides critical information of how defect production and dislocations are correlated, especially when total dose is high, which needs to be taken into account in upper scale models, such as mean-field rate theory.

Lu, Zizhe↗

Integrated Computational Study of Radiation Damage Effects in Grade 92 Steel and Alloy 709

Radiation resistance of austenitic alloy 709 (named as A709) and ferritic-martensitic steel Grade 92 (G92) were investigated in this project using 316H and Grade 91 (G91) as references, respectively. In the meantime, a model 709 (M709) alloy (Fe-20Cr-24Ni) was prepared to study the matrix response to irradiation. Samples machined from the tab section of three creep-ruptured A709 samples, i.e., 17,106 h at 600 °C, 12,014 h at 650 °C, and 16,448 h at 700 °C, were included in this work to evaluate radiation effect on the long-term “thermally aged” samples. Primarily Fe 2+ ion irradiation was conducted at 350, 600 and 670 °C for up to 75 displacements per atom (dpa), together with a few proton irradiation experiments at 380–670 °C for up to 1.5 dpa. Additionally, four neutron-irradiated NF709 samples (3.22–8 dpa at ~430–469 °C) were examined. The samples were examined by transmission electron microscopy (TEM), scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDS) for microstructures and nanoindentation for radiation-hardening

36 MATERIALS SCIENCE↗