Growing single-crystalline seeds on lithiophobic substrates to enable fast-charging lithium-metal batteries
Not provided.
Energy & Fuels↗
Engineering topics
Xing, Xing
Publications and source records attributed to Xing, Xing.
A Fiber-Based 3D Lithium Host for Lean Electrolyte Lithium Metal Batteries
3D hosts are promising to extend the cycle life of lithium metal anodes but have rarely been implemented with lean electrolytes thus impacting the practical cell energy density. To overcome this challenge, a 3D host that is lightweight and easy to fabricate with optimum pore size that enables full utilization of its pore volume, essential for lean electrolyte operations, is reported. The host is fabricated by casting a VGCF (vapor-grown carbon fiber)-based slurry loaded with a sparingly soluble rubidium nitrate salt as an additive. The network of fibers generates uniform pores of ≈3 µm in diameter with a porosity of 80%, while the nitrate additive enhances lithiophilicity. This 3D host delivers an average coulombic efficiency of 99.36% at 1 mA cm -2 and 1 mAh cm -2 for over 860 cycles in half-cell tests. Full cells containing an anode with 1.35-fold excess lithium paired with LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) cathodes exhibit capacity retention of 80% over 176 cycles at C/2 under a lean electrolyte condition of 3 g Ah -1 . This work provides a facile and scalable method to advance 3D lithium hosts closer to practical lithium-metal batteries.
36 MATERIALS SCIENCE↗
A low-cost sulfate-based all iron redox flow battery
Redox flow batteries (RFBs) are promising choices for stationary electric energy storage. Nevertheless, commercialization is impeded by high-cost electrolyte and membrane materials. Here, we report a low-cost all-iron RFB that features inexpensive FeSO 4 electrolytes, microporous membrane along with a glass fiber separator. The addition of 0.1 м 1-ethyl-3-methylimidazolium chloride (EMIC) overcomes the low solubility of FeSO 4 in water which is raised to 2.2 м. DFT calculations demonstrate that EMI + can strengthen the interaction between sulfate anions and water molecules. This electrolyte composition also allows both anode and cathode reactions to operate without actively maintaining a pH gradient between them, thus eliminating the need for expensive ion exchange membranes. The all-iron RFB demonstrates stable operation at a current density of 20 mA cm –2 for more than 800 cycles via a simple, periodic regeneration process. Furthermore, the system cost of FeSO 4 /EMIC RFBs is projected to be $ 50 per kWh due to its low-cost active materials and the inexpensive microporous membrane. Finally, this low-cost, high-concentration all-iron RFB is a promising stationary energy–storage system for storing renewable energy.
25 ENERGY STORAGE↗
Understanding the Roles of the Electrode/Electrolyte Interface for Enabling Stable Li∥Sulfurized Polyacrylonitrile Batteries
Sulfurized polyacrylonitrile (SPAN) is a promising high-capacity cathode material. Here, we use spatially resolved X-ray absorption spectroscopy combined with X-ray fluorescence (XRF) microscopy, X-ray photoelectron spectroscopy, and scanning electron microscopy to examine the structural transformation of SPAN and the critical role of a robust cathode–electrolyte interface (CEI) on the electrode. LiS x species forms during the cycling of SPAN. However, in carbonate-based electrolytes and ether-based electrolytes with LiNO 3 additives, these species are well protected by the CEI and do not dissolve into the electrolytes. In contrast, in an ether-based electrolyte without the LiNO 3 additive, LiS x species dissolve into the electrolyte, resulting in the shuttle effect and capacity loss. Examination of the Li anode by XRF and SEM reveals dense spherical Li morphology in ether-based electrolytes, but sulfur is present in the absence of the LiNO 3 additive. In contrast, porous dendritic Li is found in the carbonate electrolyte. These analyses established that an ether-based electrolyte with LiNO 3 is a superior choice that enables stable cycling of both electrodes. Based on these insights, we successfully demonstrate the stable cycling of high areal loading SPAN cathode (>6.5 mA h cm –2 ) with lean electrolyte amounts, showing promising Li∥SPAN cell performance under practical conditions.
25 ENERGY STORAGE↗
Quantification of the ion transport mechanism in protective polymer coatings on lithium metal anodes
Protective Polymer Coatings (PPCs) protect lithium metal anodes in rechargeable batteries to stabilize the Li/electrolyte interface and to extend the cycle life by reducing parasitic reactions and improving the lithium deposition morphology.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Tailoring electrolyte solvation for Li metal batteries cycled at ultra-low temperature
Not provided.
Energy & Fuels↗
An anode-free Li metal cell with replenishable Li designed for long cycle life
Pit corrosion of Li during stripping is an important factor responsible for poor Li cycling efficiency, a metric that determines its cycling life. When excess Li is present, it has been observed that Li tends to strip in a non-uniform fashion, forming pits that extend well past the theoretical Li depth that inevitably lead to the formation of electronically isolated “dead” Li particles. In this work, a novel cell with replenishable Li is shown to inherently mitigate the formation of this “dead” Li, as a direct result of a design in which the intrinsically more homogenous stripping behavior of anode-free cells are combined with a replenishable limited Li reservoir. These novel cells (Li|Cu||LiFePO 4 ) exhibit 25% and 34% higher cumulative capacities than the conventional cells (Cu|Li||LiFePO 4 ) in carbonate and ether electrolytes, respectively, enabling a significant increase in cycle life without impacting energy density. This improvement strategy represents a new direction in Li metal battery improvement, in which improved cycling can be achieved regardless of electrolyte chemistry.
Long cycle life↗
Ultrahigh coulombic efficiency electrolyte enables Li||SPAN batteries with superior cycling performance
Raising the coulombic efficiency of lithium metal anode cycling is the deciding step in realizing long-life rechargeable lithium batteries. Here, we designed a highly concentrated salt/ether electrolyte diluted in a fluorinated ether: 1.8 M LiFSI in DEE/BTFE (diethyl ether/bis(2,2,2-trifluoroethyl)ether), which realized an average coulombic efficiency of 99.37% at 0.5 mA cm -2 and 1 mAh cm -2 for more than 900 cycles. This electrolyte also maintained a record coulombic efficiency of 98.7% at 10 mA cm -2 , indicative of its ability to provide fast-charging with high cathode loadings. Morphological studies reveal dense, dendrite free Li depositions after prolonged cycling, while surface analyses confirmed the formation of a robust LiF-rich SEI layer on the cycled Li surface. Moreover, we discovered that this ether-based electrolyte is highly compatible with the low-cost, high-capacity SPAN (Sulfurized polyacrylonitrile) cathode, where the constructed Li||SPAN cell exhibited reversible cathode capacity of 579 mAh g -1 and no capacity decay after 1200 cycles. A cell where a high areal loading SPAN electrode (>3.5 mAh cm -2 ) is paired with only onefold excess Li was constructed and cycled at 1.75 mA cm -2 , maintaining a coulombic efficiency of 99.30% for the lithium metal. Computational simulations revealed that at saturation, the Li-FSI complex forms contact ion pairs, with a first solvation shell comprising DEE molecules, and a second solvation shell with a mix of DEE/BTFE. This study provides a path to enable high energy density Li||SPAN batteries with stable cycling.
36 MATERIALS SCIENCE↗
A disordered rock salt anode for fast-charging lithium-ion batteries
Rechargeable lithium-ion batteries with high energy density that can be safely charged and discharged at high rates are desirable for electrified transportation and other applications. However, the sub-optimal intercalation potentials of current anodes result in a trade-off between energy density, power and safety. In this paper we report that disordered rock salt Li 3+ x V 2 O 5 can be used as a fast-charging anode that can reversibly cycle two lithium ions at an average voltage of about 0.6 volts versus a Li/Li + reference electrode. The increased potential compared to graphite reduces the likelihood of lithium metal plating if proper charging controls are used, alleviating a major safety concern (short-circuiting related to Li dendrite growth). In addition, a lithium-ion battery with a disordered rock salt Li 3 V 2 O 5 anode yields a cell voltage much higher than does a battery using a commercial fast-charging lithium titanate anode or other intercalation anode candidates (Li 3 VO 4 and LiV 0.5 Ti 0.5 S 2 ). Further, disordered rock salt Li 3 V 2 O 5 can perform over 1,000 charge–discharge cycles with negligible capacity decay and exhibits exceptional rate capability, delivering over 40 per cent of its capacity in 20 seconds. We attribute the low voltage and high rate capability of disordered rock salt Li 3 V 2 O 5 to a redistributive lithium intercalation mechanism with low energy barriers revealed via ab initio calculations. This low-potential, high-rate intercalation reaction can be used to identify other metal oxide anodes for fast-charging, long-life lithium-ion batteries.
25 ENERGY STORAGE↗