Engineering Papers⌕ Search

Engineering topics

Wu, Amanda S.

Publications and source records attributed to Wu, Amanda S..

Active Mixing of Disparate Inks for Multimaterial 3D Printing

3D printing of multimaterial parts relies upon efficient mixing of the ink components and a rapid response to composition changes. However, at low Reynolds numbers and large Peclet numbers, mixing disparate viscosity and density inks poses a challenge. In this study, the performance of active micromixers for disparate non-Newtonian inks is evaluated using both experiments and computational fluid dynamics simulations. The mixing efficiencies are compared with scaling relationships for active micromixers. Using detailed simulation results, multiple factors are identified that can impact the micromixer response time during a composition change. Finally, an active micromixer is proposed and evaluated to efficiently mix arbitrary multimaterial ink compositions and produce fine composition gradients within printed parts.

3D printing↗

Shape memory behavior and recovery force of 4D printed textile functional composites

Four-dimensional (4D) printing of multi-directionally reinforced preforms has tremendous potential for the development of next generation functional composites by using the capabilities of 3D printing technology, 3D textile preform design, and polymer shape memory behavior. This paper demonstrates the shape memory behavior and recovery force of 4D printed circular braided tube preforms and their silicone elastomer matrix composites. The preforms were printed by fused deposition modeling using the shape memory polymer (SMP), polylactic acid (PLA). The effects of braiding angle, tube wall thickness, and shape recovery temperature on the shape memory behavior of 4D printed tube preforms and their silicone elastomer matrix composites have been characterized. Measurements of shape recovery forces of the preform and composite were conducted using dynamic mechanical analysis (DMA). The braided microstructural parameters and shape recovery temperature have a significant effect on the preform shape memory behavior. The introduction of the silicone elastomer matrix greatly enhances the shape recovery force, shape recovery ratio, as well as radial compressive failure load of the 4D printed preform/silicone elastomer matrix composite. Finally, building on these results, a potential application for 4D printed textile functional composites is presented.

42 ENGINEERING↗

Custom 3D Printable Silicones with Tunable Stiffness

Silicone elastomers have broad versatility within a variety of potential advanced materials applications, such as soft robotics, biomedical devices, and metamaterials. Furthermore, a series of custom 3D printable silicone inks with tunable stiffness is developed, formulated, and characterized. The silicone inks exhibit excellent rheological behavior for 3D printing, as observed from the printing of porous structures with controlled architectures. Here, the capability to tune the stiffness of printable silicone materials via careful control over the chemistry, network formation, and crosslink density of the ink formulations in order to overcome the challenging interplay between ink development, post-processing, material properties, and performance is demonstrated.

36 MATERIALS SCIENCE↗

Editors' Choice—Field Trials Testing of Mixed Potential Electrochemical Hydrogen Safety Sensors at Commercial California Hydrogen Filling Stations

Hydrogen safety sensors must meet specific performance requirements, mandated by the U.S. Department of Energy, for hydrogen fueling station monitoring. Here, we describe the long-term performance of two zirconia-based mixed potential electrochemical hydrogen gas sensors, developed specifically with a high sensitivity to hydrogen, low cross-sensitivity, and fast response time. Over a two-year period, sensors with tin-doped indium oxide and strontium doped lanthanum chromite electrodes were deployed at two stations in four field trials tests conducted in Los Angeles. The sensors documented the existence of hydrogen plumes ranging in concentration from 100 to as high as 2700 ppm in the area surrounding the dispenser, consistent with depressurization from 700 bar following vehicle refueling. As expected, the hydrogen concentration reported by the mixed potential sensors was influenced by wind direction. Baseline stability testing at a Chino, CA station showed no measureable baseline drift throughout 206 days of uninterrupted data acquisition. In conclusion, the high baseline stability, excellent correlation with logged fueling/depressurization events, and absence of false alarms suggest that the zirconia-based mixed potential sensor platform is a good candidate for protecting hydrogen infrastructure where frequent calibrations or sensor replacement to reduce the false alarm frequency have been shown to be cost prohibitive.

08 HYDROGEN↗

Characterization of residual stress and deformation in additively manufactured ABS polymer and composite specimens

Residual stresses induced in the layer-by-layer fabrication process of additively manufactured parts have significant impact on their mechanical properties and dimensional accuracy. This work aims here to characterize the residual stress and deformation in specimens based on unreinforced acrylonitrile-butadiene-styrene (ABS), carbon nanotube reinforced ABS and short carbon fiber reinforced ABS. The shrinkage and displacement fields were obtained, respectively, by thermal treatment as well as Digital Image Correlation observation of specimens before and after sectioning. The microstructure and porosity of additively manufactured specimens were also examined using X-ray micro-computed tomography. Specimen shrinkage and porosity content were significantly influenced by the process parameters of raster angle and printing speed, as well as material types. Faster printing speed led to larger porosity and residual stress, as well as higher shrinkage after specimen thermal treatment. Raster angle had a greater influence on specimen shrinkage and porosity as comparing to printing speed. Composite printing wires based on carbon nanotube and short carbon fiber in ABS greatly reduced specimen shrinkage and deformation, while increased the porosity, especially for carbon fiber reinforced ABS specimens.

36 MATERIALS SCIENCE↗

3D Printed Silicones with Shape Memory

Direct ink writing enables the layer-by-layer manufacture of ordered, porous structures whose mechanical behavior is driven by architecture and material properties. Here, we incorporate two different gas filled microsphere pore formers to evaluate the effect of shell stiffness and T g on compressive behavior and compression set in siloxane matrix printed structures. The lower T g microsphere structures exhibit substantial compression set when heated near and above T g , with full structural recovery upon reheating without constraint. By contrast, the higher T g microsphere structures exhibit reduced compression set with no recovery upon reheating. Aside from their role in tuning the mechanical behavior of direct ink write structures, polymer microspheres are good candidates for shape memory elastomers requiring structural complexity, with potential applications toward tandem shape memory polymers.

36 MATERIALS SCIENCE↗

3D-Printing of Meso-structurally Ordered Carbon Fiber/Polymer Composites with Unprecedented Orthotropic Physical Properties

Here we report the first example of a class of additively manufactured carbon fiber reinforced composite (AMCFRC) materials which have been achieved through the use of a latent thermal cured aromatic thermoset resin system, through an adaptation of direct ink writing (DIW) 3D-printing technology. We have developed a means of printing high performance thermoset carbon fiber composites, which allow the fiber component of a resin and carbon fiber fluid to be aligned in three dimensions via controlled micro-extrusion and subsequently cured into complex geometries. Characterization of our composite systems clearly show that we achieved a high order of fiber alignment within the composite microstructure, which in turn allows these materials to outperform equivalently filled randomly oriented carbon fiber and polymer composites. Moreover, our AM carbon fiber composite systems exhibit highly orthotropic mechanical and electrical responses as a direct result of the alignment of carbon fiber bundles in the microscale which we predict will ultimately lead to the design of truly tailorable carbon fiber/polymer hybrid materials having locally programmable complex electrical, thermal and mechanical response.

36 MATERIALS SCIENCE↗

The influence of impurities on the crystal structure and mechanical properties of additive manufactured U–14at.% Nb

Uranium-niobium alloys can exist with significantly different microstructures and mechanical properties, heavily influenced by thermomechanical processing history and impurities. In this study, the influence of Ti and other impurities is studied on uranium-14 at.% niobium additively manufactured using laser powder bed fusion. In two different metallic impurity levels were investigated and a Nb equivalent (Nbeq) composition is defined to represent the impurities. Furthermore, in-situ neutron diffraction during compression loading shows that increased Nbeq promotes the formation of γ°-tetragonal phase at the expense of α''-monoclinic phase, resulting in 2 × higher yield strength than water quenched α'' and a strain induced transformation to α'' with superelastic strains to 4.5%.

36 MATERIALS SCIENCE↗

Demonstration of a prototype hydrogen sensor and electronics package

This is a progress report for the demonstration of a prototype hydrogen sensor and electronics package. There are five tasks associated with this, and four have been completed as of August 2016: Station Demonstration and Site Recommendation, Order Sensor Equipment, Build Sensors, and Install Sensors. The final task to be completed is Sensor Demonstration and Data Analysis, and expected completion date is January 26, 2017. This progress report details each of the tasks and goes into detail about what is currently being worked on, along with the budget and planned work for July 27, 2016 to January 26, 2017.

36 MATERIALS SCIENCE↗

In-Situ Synchrotron and Neutron Radiation at International User Facilities Take Welding Research to a New Level

Over the past century the principal method for understanding the effects of welding on the mechanical and physical integrity of the final joint has been post-weld microstructure analysis, and it’s the interpretation of these microstructures that sets welding metallurgy apart from other related scientific fields. In conjunction with heat flow analysis, thermodynamics, and kinetics, post-weld visual observations have provided the framework for interpreting the events that lead to the final weld microstructure. However, without direct and confirming evidence of the actual phases that exist during welding, or measurement of invisible weld properties such as crystal structure and residual stress, multiple interpretations for microstructural evolution of welds are possible. For these reasons, new methods are being developed for the direct observation of phase transformations that occur both during and as a result of welding, using modern synchrotron and neutron user research facilities.

36 MATERIALS SCIENCE↗

Demonstration of a Prototype Hydrogen Sensor and Electronics Package - Progress Report 2

This is the second progress report on the demonstration of a prototype hydrogen sensor and electronics package. It goes into detail about the five tasks, four of which are already completed as of August 2016, with the final to be completed by January 26, 2017. Then the budget is detailed along with the planned work for May 27, 2016 to July 27, 2016.

36 MATERIALS SCIENCE↗