Engineering Papers⌕ Search

Engineering topics

Wright, Richard

Publications and source records attributed to Wright, Richard.

Complete the Planned FY24 Design Parameters Development at INL to Support the Drafting of the A709 Near-Term Code Case

This report presents the thermophysical properties measurements conducted in the Fiscal Year 2024 to extend the database up to 1000?. The new values are compared against properties of high Molybdenum steels in the ASME Section II Part D tables. This report also shows the comparison between new measurements against the previously measured values in literature and provides recommended thermophysical properties for A709 code case. These values will support the thermophysical property tables in near term code case of A709.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A709 Procurement and ASTM Specification Status

This is a presentation regarding A709 Procurement and ASTM Specification Status for the Joint ART Materials/AMMT Program Review meeting. The A709 team consists of Argonne National Laboratory, Idaho National Laboratory, Oak Ridge National Laboratory, and Subject matter expert John Grubb and Richard Wright. Discussion topics will discuss incorporation of 709 into ASTM Standard A 240 for plate material in the solution annealed condition with a precipitation treatment as a supplemental requirement is underway, Incorporation of Alloy 709 into ASME, Section II, Specification SA 240 will be made upon the completion of the ASTM task, The required commercial scale heats of Alloy 709 for property characterization to provide the technical basis for Code qualification have been procured, and Laboratory testing of properties from these three heats is underway as will be discussed separately at this review meeting.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of Conceptual Lead Cartridge Design to Perform Irradiation Experiments in VTR

This paper seeks to introduce the latest design of the Extended Length Test Assembly–Cartridge Lead (ELTA-CL) with associated thermal-hydraulic (TH) assessment and related experiment activities to support the critical component development performed by the ELTA-CL team (Los Alamos National Laboratory, Westinghouse Electric Company, and the University of New Mexico). The goal of the ELTA-CL program is to develop and validate an experimental capability to perform irradiation experiments in the Versatile Test Reactor (VTR) addressing Lead Fast Reactor (LFR) technology gaps, in support of the commercial development of advanced lead-cooled fast reactor concepts. Through a design maturation process and parametric study, a conceptual design is proposed to meet the requirements for material and corrosion testing. Thermal-hydraulic characteristics for the conceptual design at desired operating conditions are assessed with systems-level (one-dimensional) and computational fluid dynamics (three-dimensional) simulations. Along with the conceptual design work, experimental activities for the development of critical components such as the pump and flowmeter are undertaken. From both the modeling study and the experimental results, the design requirements of the Phase 1 ELTA-CL (e.g., 500°C and 2 m/s) are achievable with the current conceptual design. Additional design improvements and safety assessments at both steady-state and transient conditions for the final ELTA-CL design will be pursued.

42 ENGINEERING↗

Fuels and Materials Challenges for the Very High Temperature Reactor

High Temperature Gas-cooled Reactors (HTGRs) featuring particle fuel are a very mature technology. Commercial deployment occurred in the mid-1980's with the Fort St.Vrain and Thorium Hochtemperatur Reaktor by providing electricity to the grids in the United States and West Germany, respectively. The technology was then adopted by Japan and China with the operation of the High Temperature Test Reactor in Oarai, Japan and the High Temperature Reactor (HTR-10) in China. These commercial reactors typically operate with an outlet coolant temperature of 750 deg. C to 800 deg. C. Increasing the outlet temperature of the HTGR to even higher temperatures above 900 deg. C will improve the thermodynamic efficiency of the system and enable application of a new class of gas reactor, the very high temperature reactor (VHTR), to provide process heat, electricity, and hydrogen to a broad range of industrial customers with the attendant benefits of improved energy security and reduced CO{sub 2} emissions. However, the increase in coolant outlet temperature presents a number of technical challenges associated with fuels and materials. For over a decade, the U.S. Department of Energy has been sponsoring a broad program of research and development with a goal of addressing the technical fuels and materials challenges to support deployment of a VHTR that could safely and economically operate at outlet temperatures of 750 to 950 deg. C. In summary, fuels and materials challenges exist with deploying a VHTR with an outlet temperature of 950 deg. C in the areas of structural materials, graphite and TRISO fuel. However, R and D is underway or has recently been completed suggesting that technical solutions are possible. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The Effect of Cold Work on Properties of Alloy 617

Alloy 617 is approved for non-nuclear construction in the ASME Boiler and Pressure Vessel Code Section I and Section VIII, but is not currently qualified for nuclear use in ASME Code Section III. A draft Code Case was submitted in 1992 to qualify the alloy for nuclear service but efforts were stopped before the approval process was completed.1 Renewed interest in high temperature nuclear reactors has resulted in a new effort to qualify Alloy 617 for use in nuclear pressure vessels. The mechanical and physical properties of Alloy 617 were extensively characterized for the VHTR programs in the 1980’s and incorporated into the 1992 draft Code Case. Recently, the properties of modern heats of the alloy that incorporate an additional processing step, electro-slag re-melting, have been characterized both to confirm that the properties of contemporary material are consistent with those in the historical record and to increase the available database. A number of potential issues that were identified as requiring further consideration prior to the withdrawal of the 1992 Code Case are also being re-examined in the current R&D program. Code Cases are again being developed to allow use of Alloy 617 for nuclear design within the rules of the ASME Boiler and Pressure Vessel Code. In general the Code defines two temperature ranges for nuclear design with austenitic and nickel based alloys. Below 427°C (800°F) time dependent behavior is not considered, while above this temperature creep and creep-fatigue are considered to be the dominant life-limiting deformation modes. There is a corresponding differentiation in the treatment of the potential for effects associated with cold work. Below 427°C the principal issue is the relationship between the level of cold work and the propensity for stress corrosion cracking and above that temperature the primary concern is the impact of cold work on creep-rupture behavior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Prediction of the Creep-Fatigue Lifetime of Alloy 617: An Application of Non-destructive Evaluation and Information Integration

A relatively simple method using the nominal constant average stress information and the creep rupture model is developed to predict the creep-fatigue lifetime of Alloy 617, in terms of time to rupture. The nominal constant average stress is computed using the stress relaxation curve. The predicted time to rupture can be converted to number of cycles to failure using the strain range, the strain rate during each cycle, and the hold time information. The predicted creep-fatigue lifetime is validated against the experimental measurements of the creep-fatigue lifetime collected using conventional laboratory creep-fatigue tests. High temperature creep-fatigue tests of Alloy 617 were conducted in air at 950°C with a tensile hold period of up to 1800s in a cycle at total strain ranges of 0.3% and 0.6%. It was observed that the proposed method is conservative in that the predicted lifetime is less than the experimentally determined values. The approach would be relevant to calculate the remaining useful life to a component like a steam generator that might fail by the creep-fatigue mechanism.

36 MATERIALS SCIENCE↗

Low Cycle Fatigue and Creep-Fatigue Behavior of Alloy 617 at High Temperature

Alloy 617 is the leading candidate material for an intermediate heat exchanger (IHX) application of the Very High Temperature Nuclear Reactor (VHTR), expected to have an outlet temperature as high as 950 degrees C. Acceptance of Alloy 617 in Section III of the ASME Code for nuclear construction requires a detailed understanding of the creep-fatigue behavior. Initial creep-fatigue work on Alloy 617 suggests a more dominant role of environment with increasing temperature and/or hold times evidenced through changes in creep-fatigue crack growth mechanism/s and failure life. Continuous cycle fatigue and creep-fatigue testing of Alloy 617 was conducted at 950 degrees C and 0.3% and 0.6% total strain in air to simulate damage modes expected in a VHTR application. Continuous cycle specimens exhibited transgranular cracking. Intergranular cracking was observed in the creep-fatigue specimens, although evidence of grain boundary cavitation was not observed. Despite the absence of grain boundary cavitation to accelerate crack propagation, the addition of a hold time at peak tensile strain was detrimental to cycle life. This suggests that creepfatigue interaction may occur by a different mechanism or that the environment may be partially responsible for accelerating failure.

36 MATERIALS SCIENCE↗

VHTR Materials Overview

The PowerPoint presentation was given at the DOE-NE Materials Crosscut Coordination Meeting, Tuesday, 30 July 2013.

High temperature metals, alloy 617, microstructure↗

Aging of Alloy 617 at 650 and 750°C

Alloy 617 has been selected as the primary candidate for heat exchanger applications in advanced reactors. For the VHTR this application could require extended service up to a reactor outlet temperature of 950°C. A key hurdle to using this alloy in the VHTR heat exchanger application is qualifying the alloy for Section III of the ASME Boiler and Pressure Vessel Code. In order to Code qualify the material it is necessary to characterize the influence of long term aging on the mechanical behavior. Alloy 617 has been aged at 650 and 750°C for times up to 5300 hours. The microstructure after aging has been characterized using optical and transmission electron microscopies. It has been determined that in addition to carbides, a significant volume fraction of γ’ phase (Ni 3 Al) is formed at these temperatures. The γ’ does not contribute significantly to changing the tensile or impact properties of the aged material. It does, however, appear to increase creep resistance and impede creep crack growth.

36 MATERIALS SCIENCE↗

Current Status of VHTR Technology Development

Abstract – High Temperature Gas-cooled Reactors (HTGRs) featuring particle fuel reached the stage of commercial deployment in the mid-1980s with the Fort St.Vrain and Thorium HochTemperatur Reaktor feeding electricity to the grids in the United States and West Germany, respectively. The technology was then adopted by Japan and China with the operation of the High Temperature Test Reactor in Oarai, Japan and the High Temperature Reactor (HTR-10) in China. Increasing the outlet temperature of the HTGR to even higher temperatures above 900°C will improve the thermodynamic efficiency of the system and enable application of a new class of gas reactor, the very high temperature reactor, to provide process heat, electricity, and hydrogen to chemical industries with the attendant benefits of improved energy security and reduced CO2 emissions. However, the increase in coolant outlet temperature presents a number of technical challenges associated with fuel, materials, power conversion, and analysis methods for the reactor and hydrogen production. The U.S. Department of Energy is sponsoring a broad program of research and development with a goal of addressing the technical challenges over a broad range of outlet temperatures as part of the Next Generation Nuclear Plant Project. This paper describes the research and development activities that are currently underway to realize the technologies needed for an HTGR that features outlet temperatures of 750 to 950°C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructure, Processing, Performance Relationships for High Temperature Coatings

HVOF coatings have shown high resistance to corrosion in fossil energy applications and it is generally accepted that mechanical failure, e.g. cracking or spalling, ultimately will determine coating lifetime. The high velocity oxygen-fuel method (HVOF) for applying coatings is one of the most commercially viable and allows the control of various parameters including powder particle velocity and temperature which influence coating properties, such as residual stress, bond coat strength and microstructure. The mechanical durability of coatings is being assessed using a dual eddy current coil method to monitor crack formation in real time during thermal cycling. Absolute impedence signals from two coils, which interrogate two different areas on the sample, are collected. Crack detection can be determined from the differential signal generated from these absolute signals. The coils are operated at two different frequencies, resulting in two differential signals used for crack detection. Currently this crack detection method is being used to elucidate the influence of thermal cycling temperature and coating thickness on cracking. Recent results (cycles to failure) will be presented for FeAl coatings thermally sprayed (HVOF) onto carbon steel to two coating thicknesses (160 microns and 250 microns thick) and subsequently cycled at temperatures up to 700oC. Thinner coatings exhibit greater resistance to cracking. Ultimately the resistance to cracking will be used to explore the relationship between HVOF spraying parameters, the mechanical properties of the coating and coating bond strength to develop optimized thermal spray parameters. To this end thermal spray coatings (FeAl and Fe3Al) have been applied to additional alloy substrates (Grade 91 steel, 316 SS, etc.) relevant to the fossil industry. Future plans also include a direct comparison to conventional weld overlay coatings currently used in the industry as well as exploration of new coatings. The room temperature mechanical strength and coating adhesion to the substrate is also of considerable importance. Eddy current methods are being developed to detect coating failure during room temperature tensile tests to optimize surface preparation as well as aid in the optimization of the HVOF thermal spray parameters.

20 FOSSIL-FUELED POWER PLANTS↗