Engineering topics

Wright, C. W.

Publications and source records attributed to Wright, C. W..

17 records

NASA NTRS2010

Ultrasonic Monitoring of Ply Crack and Delamination Formation in Composite Tube Under Torsion Load

As a simple model of a rotor spar, a circular graphite-epoxy composite laminate cylinder was subjected to cyclic torsional load. The test section of the cylindrical specimen varied from four to six plies of plus or minus 45 degree fibers, due to intentional ply overlaps and gaps. A layer of 13-micrometer Teflon film was inserted between plies at three locations to serve as delamination initiators. A commercial X-Y scanner was mounted to the load frame to enable ultrasonic inspection without removing the specimen. A focused immersion probe was mounted in a captive water column with a rugged Nitrile membrane tip, which was coupled to the cylinder using a mist of soapy water. The transducer was aligned normal to the cylinder surface using the X-axis. Scanning was performed along the length of the specimen with the Y-axis and the specimen was incrementally rotated by the torsion head of the load frame. After 350k cycles of torsion, several linear 45 degree diagonal indications appeared as 5-40% attenuation of the back wall echo, with no apparent echoes from the interior of the composite, suggesting through-ply cracks in the innermost ply. Crack indications grew and new cracks appeared as torsion cycling continued. Internal reflections from delaminations associated with the growing ply cracks appeared after 500k cycles. Three areas of extensive multi-layer delaminations appeared after 1150k cycles. Failure of the specimen occurred at 1600k cycles. The observed progressive damage was not associated with the Teflon inclusions. Concurrent thermographic measurements provided lower resolution confirmation of the damage observed.

Johnston, P. H.↗

NASA NTRS2008

Storm Surge Measurement with an Airborne Scanning Radar Altimeter

Over the years, hurricane track and intensity forecasts and storm surge models and the digital terrain and bathymetry data they depend on have improved significantly. Strides have also been made in knowledge of the detailed variation of the surface wind field driving the surge. The area of least improvement has been in obtaining data on the details of the temporal/spatial variation of the storm surge dome of water as it evolves and inundates the land to evaluate the performance of the numerical models. Tide gages in the vicinity of the landfall are frequently destroyed by the surge. Survey crews dispatched after the event provide no temporal information and only indirect indications of the maximum surge envelope over land. The landfall of Hurricane Bonnie on 26 August 1998, with a surge less than 2 m, provided an excellent opportunity to demonstrate the potential benefits of direct airborne measurement of the temporal/spatial evolution of storm surge. Despite a 160 m variation in aircraft altitude, an 11.5 m variation in the elevation of the mean sea surface relative to the ellipsoid over the flight track, and the tidal variation over the 5 hour data acquisition interval, a survey-quality Global Positioning System (GPS) aircraft trajectory allowed the NASA Scanning Radar Altimeter carried by a NOAA hurricane research aircraft to produce storm surge measurements that generally fell between the predictions of the NOAA SLOSH model and the North Carolina State University storm surge model.

Wright, C. W.↗

NASA NTRS2001

Bathymetric Effects on a Tropical Cyclone Wave Field at Landfall

On 26 August 1998, the NASA Scanning Radar Altimeter (SRA) flew aboard one of the WP-3D hurricane research aircraft to document the sea surface directional wave spectrum in the region between Charleston, SC and Cape Hatteras, NC, as Bonnie, a large Category 3 hurricane, was making landfall near Wilmington, NC. Two days earlier, the SRA had documented the wave field spatial variation in open water when Hurricane Bonnie was 400 km east of Abaco Island, Bahamas. Bonnie was similar in size during the two flights, but the maximum speed in the NOAA Hurricane Research Division surface wind analysis was 15% lower prior to landfall (39 m/s) than it had been in the open ocean (46 m/s). This was compensated for by its faster movement prior to landfall (9.5 m/s) than when it was encountered in the open ocean (5 m/s). The slower movement matched the group velocity of waves of 65 m length, so waves at the peak of the spectrum outdistanced the storm as soon as they were generated. The higher translation speed prior to landfall matched the group velocity of waves of 230 m length, significantly increasing the effective fetch and duration of waves near the peak of the spectrum which propagated in the direction of the storm track. The open ocean wave height variation indicated that Hurricane Bonnie would have produced waves of 11 m significant wave height on the shore northeast of Wilmington had it not been for the continental shelf. The bathymetry distributed the steepening and breaking process across the shelf so that the wavelength and wave height were reduced gradually as the shore was approached. The wave height 5 km from shore was about 4 m.

Wright, C. W.↗

NASA NTRS2001

Hurricane Directional Wave Spectrum Spatial Variation at Landfall

On 26 August 1998, the SRA at 2.2 km height documented the directional wave spectrum in the region between Charleston, SC, and Cape Hatteras, NC, as Hurricane Bonnie was making landfall near Wilmington, NC. The storm was similar in size during the two flights, but the maximum speed in the NOAA Hurricane Research Division surface wind analysis was 15% lower prior to landfall (39 m/s) than it had been in the open ocean (46 m/s). This was compensated for by its faster movement prior to landfall (9.5 m/s) than when it was encountered in the open ocean (5 m/s), significantly increasing the effective fetch and duration of waves near the peak of the spectrum which propagated in the direction of the storm track. The open ocean wave height variation indicated that Hurricane Bonnie would have produced waves of 11 m significant wave height on the shore northeast of Wilmington had it not been for the continental shelf. The bathymetry distributed the steepening and breaking process across the shelf so that the wavelength and wave height were reduced gradually as the shore was approached. The wave height 5 km from shore was about 4 in.

Walsh, E. J.↗

NASA NTRS2001

Observations of Sea Surface Mean Square Slope During the Southern Ocean Waves Experiment

For the Southern Ocean Waves Experiment (SOWEX), conducted in June 1992 out of Hobart, Tasmania, the NASA Scanning Radar Altimeter (SRA) was shipped to Australia and installed on a CSIRO Fokker F-27 research aircraft instrumented to make comprehensive surface layer measurements of air-sea interaction fluxes. The SRA sweeps a radar beam of P (two-way) half-power width across the aircraft ground track over a swath equal to 0.8 of the aircraft height, simultaneously measuring the backscattered power at its 36 GHz (8.3 mm) operating frequency and the range to the sea surface at 64 cross-track positions. In realtime, the slant ranges are multiplied by the cosine of the off-nadir incidence angles (including the effect of aircraft roll attitude) to determine the vertical distances from the aircraft to the sea surface. These distances are subtracted from the aircraft height to produce a sea-surface elevation map, which is displayed on a monitor in the aircraft to enable real-time assessments of data quality and wave properties. The sea surface mean square slope (mss), which is predominantly caused by the short waves, was determined from the backscattered power falloff with incidence angle measured by the SRA in the plane normal to the aircraft heading. On each flight, data were acquired at 240 m altitude while the aircraft was in a 7 degree roll attitude, interrogating off-nadir incidence angles from -15 degrees through nadir to +29 degrees. The aircraft turned azimuthally through 810 degrees in this attitude, mapping the azimuthal dependence of the backscattered power falloff with incidence angle. Two sets of turning data were acquired on each day, before and after the aircraft measured wind stress at low altitude (12 meters to 65 meters). Wave topography and backscattered power for mss were also acquired during those level flight segments whenever the aircraft altitude was above the SRA minimum range of 35 m. Data were collected over a wide range of wind and sea conditions, from quiescent to gale force winds with 9 meter wave height.

Walsh, E. J.↗

NASA NTRS2001

Hurricane Directional Wave Spectrum Spatial Variation in the Open Ocean and at Landfall

The sea surface directional wave spectrum was measured for the first time in all quadrants of a hurricane in open water using the NASA scanning radar altimeter (SRA) carried aboard one of the NOAA WP-3D hurricane research aircraft at 1.5 kilometer height. The SRA measures the energetic portion of the directional wave spectrum by generating a topographic map of the sea surface. The data were acquired on 24 August 1998 when Hurricane Bonnie was 400 km east of Abaco Island, Bahamas. Individual waves with heights up to 19 meters were observed and the spatial variation of the wave field was dramatic. The dominant waves generally propagated at significant angles to the downwind direction. At one position, three different wave systems of comparable energy and wavelength crossed each other. The aircraft spent over five hours within 180 kilometers of the Hurricane Bonnie eye and made five eye penetrations. On 26 August 1998, the SRA at 2.2 kilometer height documented the directional wave spectrum in the region between Charleston, SC, and Cape Hatteras, NC, as Hurricane Bonnie was making landfall near Wilmington, NC. The storm was similar in size during the two flights, but the maximum speed in the NOAA Hurricane Research Division surface wind analysis was 15% lower prior to landfall (39 meters per second) than it had been in the open ocean (46 meters per second). This was compensated for by its faster movement prior to landfall (9.5 meters per second) than when it was encountered in the open ocean (5 meters per second), significantly increasing the effective fetch and duration of waves near the peak of the spectrum which propagated in the direction of the storm track. The open ocean wave height variation indicated that Hurricane Bonnie would have produced waves of 11 meters significant wave height on the shore northeast of Wilmington had it not been for the continental shelf. The bathymetry distributed the steepening and breaking process across the shelf so that the wavelength and wave height were reduced gradually as the shore was approached. The wave height 5 kilometers from shore was about 4 meters.

Walsh, E. J.↗

NASA NTRS2000

Five Year Changes in Surface Elevations Of The Greenland Ice Sheet Measured by Aircraft Laser Altimetry

The Arctic Ice Mapping group (Project AIM) at NASA's Wallops Flight Facility has been conducting systematic topographic surveys of the Greenland Ice Sheet since 1993, using scanning airborne laser altimeters combined with GPS positioning technology. Flight lines were planned to cover all major ice drainage basins, with the intention to repeat the surveys after a 5-year interval in order to detect changes in the ice-sheet volume. The first resurvey was completed in June/July, 1998, along flight lines in the southern half of Greenland which had been first surveyed in 1993. The northern half of the ice sheet will be resurveyed in 1999. The resulting data sets will provide the first comprehensive examination of regional changes in the the surface elevation of the World's second largest ice sheet. This analysis includes the ice sheet fringe areas, which are expected to be much more climatically sensitive than the interior. Data will be presented which demonstrate the combination of the ATM (Airborne Topographic Mapper) sensors and GPS (Global Positioning System) yields measurements which are repeatable at the 10 cm level over baselines in excess of 1000 km.

Krabill, W. B.↗

NASA NTRS2000

Hurricane Directional Wave Spectrum Spatial Variation in the Open Ocean and at Landfall

The sea surface directional wave spectrum was measured for the first time in all quadrants of a hurricane in open water using the NASA airborne scanning radar altimeter (SRA) carried aboard one of the NOAA WP-3D hurricane hunter aircraft at 1.5 km height. The SRA measures the energetic portion of the directional wave spectrum by generating a topographic map of the sea surface. At 8 Hz, the SRA sweeps a radar beam of 1 E half-power width (two-way) across the aircraft ground track over a swath equal to 0.8 of the aircraft height, simultaneously measuring the backscattered power at its 36 GHz (8.3 mm) operating frequency and the range to the sea surface at 64 positions. These slant ranges are multiplied by the cosine of the incidence angles to determine the vertical distances from the aircraft to the sea surface. Subtracting these distances from the aircraft height produces the sea surface elevation map. The sea surface topography is interpolated to a uniform grid, transformed by a two-dimensional FFT, and Doppler corrected. The open-ocean data were acquired on 24 August 1998 when hurricane Bonnie was east of the Bahamas and moving slowly to the north. Individual waves with heights up to 18 m were observed and the spatial variation of the wave field was dramatic. The dominant waves generally propagated at significant angles to the downwind direction. At some positions there were three different wave fields of comparable energy crossing each other. The NOAA aircraft spent over five hours within 180 km of the hurricane Bonnie eye, and made five eye penetrations. A 3-minute animation of the directional wave spectrum spatial variation over this period will be shown as well as summary plots of the wave field spatial variation. On 26 August 1998, the NOAA aircraft flew at 2.2 km height when hurricane Bonnie was making landfall near Wilmington, NC, documenting the directional wave spectrum in the region between Charleston, SC and Cape Hatteras, NC. The aircraft ground track included both segments along the shoreline and Pamlico Sound as well as far offshore. An animation of the directional wave spectrum spatial variation at landfall will be presented and contrasted with the spatial variation when Bonnie was in the open ocean on 24 August 1998.

Walsh, E. J.↗

NASA NTRS1999

Hurricane Directional Wave Spectrum Spatial Variation in the Open Ocean

The sea surface directional wave spectrum was measured for the first time in all quadrants of a hurricane in open water using the NASA airborne scanning radar altimeter (SRA) carried aboard one of the NOAA WP-3D hurricane hunter aircraft at 1.5 km height. The SRA measures the energetic portion of the directional wave spectrum by generating a topographic map of the sea surface. At 8 Hz, the SRA sweeps a radar beam of 1 deg half-power width (two-way) across the aircraft ground track over a swath equal to 0. 8 of the aircraft height, simultaneously measuring the backscattered power at its 36 GHz (8.3 mm) operating frequency and the range to the sea surface at 64 positions. These slant ranges are multiplied by the cosine of the incidence angles to determine the vertical distances from the aircraft to the sea surface. Subtracting these distances from the aircraft height produces the sea surface elevation map. The sea surface topography is interpolated to a uniform grid, transformed by a two-dimensional FFT, and Doppler corrected. The data presented were acquired on 24 August 1998 when hurricane Bonnie was east of the Bahamas and moving slowly to the north. Wave heights up to 18 m were observed and the spatial variation of the wave field was dramatic. The dominant waves generally propagated at significant angles to the downwind direction and at times there were wave fields traveling at right angles to each other. The NOAA aircraft spent over five hours within 180 km of the hurricane Bonnie eye, and made five eye penetrations. A 2-minute animation of the directional wave spectrum spatial variation over this period will be shown.

Wright, C. W.↗

NASA NTRS1999

Hurricane Directional Wave Spectrum Spatial Variation at Landfall

On 26 August 1998, hurricane Bonnie was making landfall near Wilmington, NC. The NASA airborne scanning radar altimeter (SRA) carried aboard one of the NOAA WP-3D hurricane hunter aircraft at 2.2 km height documented the sea surface directional wave spectrum in the region between Charleston, SC and Cape Hatteras, NC. The aircraft ground track included both segments along the shoreline and Pamlico Sound as well as far offshore. An animation of the directional wave spectrum spatial variation at landfall will be presented and contrasted with the spatial variation when Bonnie was in the open ocean on 24 August 1998.

Walsh, E. J.↗

NASA NTRS1999

Measuring Directional Wave Spectra and Wind Speed with a Scanning Radar Altimeter

The geometry for the NASA Scanning Radar Altimeter (SRA) is shown. It transmits a 8-ns duration pulse at Ka-band (8.3 mm) and measures time of flight as it scans a 1 degree (two-way) beam from left to right across the aircraft ground track. The most recent configuration determines the surface elevation at 64 points spaced at uniform angular intervals of about 0.7 across a swath whose width is about 0.8 times the aircraft altitude. The system generates these raster lines of the surface topography beneath the aircraft at about a 10 Hz rate. In postflight processing the SRA wave topographic data are transformed with a two-dimensional Fast Fourier Transformation (FFT) and Doppler corrected to produce directional wave spectra. The SRA is not absolutely calibrated in power, but by measuring the relative fall-off of backscatter with increasing incidence angle, the SRA can also determine the mean square slope (mss) of the sea surface, a surrogate for wind speed. For the slope-dependent specular point model of radar sea surface scattering, an expression approximated by a geometric optics form, for the relative variation with incidence angle of the normalized backscatter radar cross section would be sigma (sup 0) (sub rel) = sec (exp 4) theta exp (-tan squared theta/mss) where theta is the off-nadir incidence angle.

Walsh, E. J.↗

NASA NTRS1997

Airborne Laser/GPS Mapping of Assateague National Seashore Beach

Results are presented from topographic surveys of the Assateague Island National Seashore using recently developed Airborne Topographic Mapper (ATM) and kinematic Global Positioning System (GPS) technology. In November, 1995, and again in May, 1996, the NASA Arctic Ice Mapping (AIM) group from the Goddard Space Flight Center's Wallops Flight Facility conducted the topographic surveys as a part of technology enhancement activities prior to conducting missions to measure the elevation of extensive sections of the Greenland Ice Sheet as part of NASA's Global Climate Change program. Differences between overlapping portions of both surveys are compared for quality control. An independent assessment of the accuracy of the ATM survey is provided by comparison to surface surveys which were conducted using standard techniques. The goal of these projects is to mdke these measurements to an accuracy of +/- 10 cm. Differences between the fall 1995 and 1996 surveys provides an assessment of net changes in the beach morphology over an annual cycle.

Kradill, W. B.↗

NASA NTRS1992

Application of new GPS aircraft control/display system to topographic mapping of the Greenland ice cap

A new PC-based GPS flight management display system (GFMS) was developed for Greenland ice cap mapping during the NASA Greenland Ice Sheet mapping experiment, when a total of nine flights were made over four different flight tracks, of which two coincided with ground tracks of the ERS altimeter satellite. In this system, the GFMS inputs the GPS position data to a PC, which generates aircraft automatic pilot steering commands and a cockpit display. The display includes (1) the course deviation indicators for cross-track error and altitude, (2) the flight plan and waypoint map overlay oriented to the aircraft, and (3) various other mission-pertinent numerical data.

Wright, C. W.↗

NASA NTRS1988

Advanced altimetry

The radar altimeter being developed for the Ocean Topography Experiment (TOPEX) will have an inherent instrument precision of 2 to 3 cm. While some minor refinements may be possible in the future, major geophysical advances could be made if altimetric measurements over a wide swath of the Earth's surface were possible. The NASA Headquarters Oceanic Processes Branch is supporting a 3-year investigation of the technological issues inherent in the precision measurement of topography from spaceborne platforms at angles off-nadir. To explore the off-nadir measurement of topography, a flexible, airborne radar instrument system is being developed. Its hardware design is now complete, and it is made up of several subsystems. The antenna selected is a dielectric lens of .894 m diameter. The RF subsystem uses phase-locked oscillators, FET solid-state amplifiers, and times four frequency multipliers to develop a transmit signal at a frequency of 36.0 GHz and a local oscillator signal at a frequency of 35.4 GHz. Lecroy 6880 digitizers under computer control digitize the five receiver outputs. The digital subsystem consists of six single-board Heurikon processors. At this time, the instrument construction continues with final system integration planned for November 1988.

Parsons, C. L.↗

NASA NTRS1988

NASA Charge Coupled Device (CCD) Spectrometer System (NCSS)

A small lightweight NCSS was designed, constructed, and is now being bench tested at Wallops. The unit provides 256, 2.7 nm wide channels in the visible spectrum from approximately 400 to 1100 nm. The present input slit provides a spectral impulse response of about 10 nm. Up to five NCSS sensors may be bused to one data system interface. The NCSS contains a high speed, 16 bit analog to digital converter (ADC) with an integral wide-band sample-and-hold amplifier. The NCSS was developed primarily for use with the Airbone Oceanographic Lidar (AOL). A prototype NCSS is presently interfaced to the AOL. The AOL will use two new NCSS units onboard the Goddard P-3A aircraft. They will provide the AOL with high resolution sky and ocean spectra. The up-looking NCSS will provide the AOL data system (AOLDS) with down-welling solar radiance, and the down-looking NCSS will provide ocean color spectra. The solar radiance will be used to correct various ocean color algorithms now being researched.

Wright, C. W.↗

NASA NTRS1988

The Surface Wave Dynamics Experiment (SWADE)

SWADE was developed to study the dynamics of the wave field development in the open ocean with the following specific objectives: (1) to understand the development of the wave directional spectrum under various conditions; (2) to determine the effect of waves on the air/sea transfers of momentum, heat, and mass; (3) to determine breaking distributions as a function of sea state, wind, and boundary stability; and (4) to provide data and analyses for ERS-1 validation. The experiment is designed for the winter of 1990 to 1991. Four buoys will be deployed for 6 months starting October 1990 and ending March 1991. During that time period, three intensive periods of 2 weeks duration each will be selected for frequent aircraft flights for wave data collection to satisfy scientific studies, as well as ERS-1 validation needs.

Long, S. R.↗

NASA NTRS1988

A multiprocessor airborne lidar data system

A new multiprocessor data acquisition system was developed for the existing Airborne Oceanographic Lidar (AOL). This implementation simultaneously utilizes five single board 68010 microcomputers, the UNIX system V operating system, and the real time executive VRTX. The original data acquisition system was implemented on a Hewlett Packard HP 21-MX 16 bit minicomputer using a multi-tasking real time operating system and a mixture of assembly and FORTRAN languages. The present collection of data sources produce data at widely varied rates and require varied amounts of burdensome real time processing and formatting. It was decided to replace the aging HP 21-MX minicomputer with a multiprocessor system. A new and flexible recording format was devised and implemented to accommodate the constantly changing sensor configuration. A central feature of this data system is the minimization of non-remote sensing bus traffic. Therefore, it is highly desirable that each micro be capable of functioning as much as possible on-card or via private peripherals. The bus is used primarily for the transfer of remote sensing data to or from the buffer queue.

Wright, C. W.↗