Engineering Papers⌕ Search

Engineering topics

Woollett, R. R.

Publications and source records attributed to Woollett, R. R..

16 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Effect of variable inlet guide vanes on the operating characteristics of a tilt nacelle inlet/powered fan model

The effects of a variable inlet guide vane (VIGV) assembly on the operating characteristics of a V/STOL inlet and on the performance of a 20-in. (0.508-m) diameter fan engine were investigated. The data indicate that the VIGVs are effective thrust modulators over a wide range of free-stream velocities, nacelle angles of attack, and fan speeds. The thrust modulation ranges, including choking limits, fan stall limits, and inlet separation boundaries are presented. The presence of the VIGV assembly causes significant losses in inlet angle-of-attack capability and generally increases the blade stress levels at all limit conditions except at high angle of attack and high free-stream velocity. Reducing the fan nozzle exit area limited the positive VIGV actuation range and consequently decreased the range of thrust modulation at all limit conditions except at both high free-stream velocity and high angle of attack conditions.

Woollett, R. R.↗
NASA NTRS1983

Aerodynamic performance of a fan stage utilizing variable inlet guide vanes (VIGV's) for thrust modulation

An experimental research program was conducted in the Lewis Research Center's 9 x 15-foot (2.74 x 4.57 m) low speed wind tunnel to evaluate the aerodynamic performance of an inlet and fan system with variable inlet guide vanes (VIGVs) for use on a subsonic V/STOL aircraft. At high VIGV blade angles (lower weight flow and thrust levels), the fan stage was stalled over a major portion of its radius. In spite of the stall, fan blade stresses only exceeded the limits at the most extreme flow conditions. It was found that inlet flow separation does not necessarily lead to poor inlet performance or adverse fan operating conditions. Generally speaking, separated inlet flow did not adversely affect the fan blade stress levels. There were some cases, however, at high VIGV angles and high inlet angles-of-attack where excessive blade stress levels were encountered. An evaluation term made up of the product of the distortion parameter, K alpha, the weight flow and the fan pressure ratio minus one, was found to correlate quite well with the observed blade stress results. Previously announced in STAR as N83-27957

Woollett, R. R.↗
NASA NTRS1983

Aerodynamic performance of a fan stage utilizing Variable Inlet Guide Vanes (VIGVs) for thrust modulation

An experimental research program was conducted in the Lewis Research Center's 9x15-foot (2.74x4.57 m) low speed wind tunnel to evaluate the aerodynamic performance of an inlet and fan system with variable inlet guide vanes (VIGVs) for use on a subsonic V/STOL aircraft. At high VIGV blade angles (lower weight flow and thrust levels), the fan stage was stalled over a major portion of its radius. In spite of the stall, fan blade stresses only exceeded the limits at the most extreme flow conditions. It was found that inlet flow separation does not necessarily lead to poor inlet performance or adverse fan operating conditions. Generally speaking, separated inlet flow did not adversely affect the fan blade stress levels. There were some cases, however, at high VIGV angles and high inlet angles-of-attack where excessive blade stress levels were encountered. An evaluation term made up of the product of the distortion parameter, K alpha, the weight flow and the fan pressure ratio minus one, was found to correlate quite well with the observed blade stress results.

Woollett, R. R.↗
NASA NTRS1982

Wind tunnel tests of a zero length, slotted-lip engine air inlet for a fixed nacelle V/STOL aircraft

Zero length, slotted lip inlet performance and associated fan blade stresses were determined during model tests using a 20 inch diameter fan simulator in the NASA-LeRC 9 by 15 foot low speed wind tunnel. The model configuration variables consisted of inlet contraction ratio, slot width, circumferential extent of slot fillers, and length of a constant area section between the inlet throat and fan face. The inlet performance was dependent on slot gap width and relatively independent of inlet throat/fan face spacer length and slot flow blockage created by 90 degree slot fillers. Optimum performance was obtained at a slot gap width of 0.36 inch. The zero length, slotted lip inlet satisfied all critical low speed inlet operating requirements for fixed horizontal nacelles subsonic V/STOL aircraft.

Woollett, R. R.↗
NASA NTRS1981

Thrust modulation methods for a subsonic V/STOL aircraft

Attention is given to four techniques for attaining thrust modulation, namely (1) varying the engine rotational speed; (2) varying the fan nozzle exit area; (3) changing the thrust of the propulsion system by using a variable pitch rotor; and (4) changing the thrust by means of variable inlet guide vanes. The thrust modulation range, thrust level, and blade stresses are examined for each of the thrust modulation systems. Results are shown at the high angles of attack associated with tilt-nacelle V/STOL aircraft. Finally, the interrelationship between the inlet and the thrust modulation system is illustrated for two inlet types.

Woollett, R. R.↗
NASA NTRS1981

Zero-length inlets for subsonic V/STOL aircraft

Zero-length inlet performance and associated fan blade stresses were determined during model tests in the NASA-LeRC 9-by 15-foot low-speed wind tunnel. The inlet models, which were installed on a 20-inch diameter fan unit, had different inlet lip contraction ratios as well as unslotted, slotted, and double slotted inlet lips. The inlet angle-of-attack boundaries for onset of flow separation were identified and compared to the operating requirements of several generically different subsonic V/STOL aircraft. The zero-length inlets, especially those with slotted lips, were able to satisfy these requirements without compromising the maximum cowl forebody radius. As an aid to the inlet design process, a unique relationship was established between the maximum surface Mach number associated with the separation boundary and the maximum-to-throat surface velocity ratio.

Glasgow, E. R.↗
NASA NTRS1981

Thrust modulation methods for a subsonic V/STOL aircraft

Low speed wind tunnel tests were conducted to assess four methods for attaining thrust modulation for V/STOL aircraft. The four methods were: (1) fan speed change, (2) fan nozzle exit area change, (3) variable pitch rotor (VPR) fan, and (4) variable inlet guide vanes (VIGV). The interrelationships between inlet and thrust modulation system were also investigated using a double slotted inlet and thick lip inlet. Results can be summarized as: (1) the VPR and VIGV systems were the most promising, (2) changes in blade angle to obtain changes in fan thrust have significant implications for the inlet, and (3) both systems attained required level of thrust with acceptable levels of fan blade stress.

Woollett, R. R.↗
NASA NTRS1980

Zero-length, slotted-lip inlet for subsonic military aircraft

Zero-length, slotted-lip inlet performance and associated fan blade stresses were determined during model tests using a 20-inch diameter fan simulator in the NASA-LeRC 9- by 15-foot low-speed wind tunnel. The model configuration variables consisted of inlet contraction ratio, slot width, circumferential extent of slot fillers, and length of a constant area section between the inlet throat and fan face. Inlet configurations having contraction ratios of 1.2 and 1.3 satisfied all critical low-speed inlet operating requirements for a fixed horizontal nacelle and tilt-nacelle-type subsonic V/STOL aircraft, respectively. Relative to a conventional axisymmetric tilt-nacelle inlet, the zero-length, slotted-lip inlet has a 27-percent smaller inlet lip contraction ratio, an 83-percent shorter total length, and a 5-percent smaller maximum cowl diameter.

Glasgow, E. R.↗
NASA NTRS1975

Transonic off-design drag and performance of three mixed-compression axisymmetric inlets

An experimental investigation was conducted to determine the off-design drag and pressure performance of three axisymmetric supersonic inlets in the transonic speed range. For typical engine airflows at Mach 0.8 the drag coefficient varied from 0.045 to 0.09; at Mach 1.2 the largest drag coefficient measured was 0.25. Below Mach 0.9 a lower drag resulted when all or at least part of the excess weight flow was spilled over the cowl rather than through the bypass doors; above Mach 1.1 the lowest drag was obtained by bypassing excess flow.

Woollett, R. R.↗
NASA NTRS1974

Transonic off-design drag and performance of an axisymmetric inlet with 40 percent internal contraction on design

An experimental investigation determined the drag and pressure performance of an axisymmetric supersonic inlet when operated in the transonic speed range. The inlet configuration was derived from a Mach 2.5 mixed compression inlet design with assumed variable geometry. At typical engine airflows the drag coefficient varied from 0.057 to 0.192 when the Mach number changed from 0.80 to 1.27. The presence of a wing simulator resulted in a sizable increase in total drag at Mach 1.2. This interference drag, which is roughly a 0.1 increase in drag coefficient, originates equally from an increase in both additive and cowl pressure drag.

Woollett, R. R.↗
NASA NTRS1973

Performance of an ion-cyclotron-wave plasma apparatus operated in the radiofrequency sustained mode

An experimental study has been made of an ion-cyclotron-wave apparatus operated in the RF-sustained mode, that is, a mode in which the Stix RF coil both propagates the waves and maintains the plasma. Problems associated with this method of operation are presented. Some factors that are important to the coupling of RF power are noted. In general, the wave propagation and wave damping data agree with theory. Some irregularities in wave fields are observed. Maximum ion temperature is 870 eV at a density of five times 10 to the 12th power cu cm and RF power of 90 kW. Coupling efficiency is 70 percent.

Swett, C. C.↗