Engineering topics

Wood, V. E.

Publications and source records attributed to Wood, V. E..

18 records

NASA NTRS1984

Luneburg lens and optical matrix algebra research

Planar, as opposed to channelized, integrated optical circuits (IOCs) were stressed as the basis for computational devices. Both fully-parallel and systolic architectures are considered and the tradeoffs between the two device types are discussed. The Kalman filter approach is a most important computational method for many NASA problems. This approach to deriving a best-fit estimate for the state vector describing a large system leads to matrix sizes which are beyond the predicted capacities of planar IOCs. This problem is overcome by matrix partitioning, and several architectures for accomplishing this are described. The Luneburg lens work has involved development of lens design techniques, design of mask arrangements for producing lenses of desired shape, investigation of optical and chemical properties of arsenic trisulfide films, deposition of lenses both by thermal evaporation and by RF sputtering, optical testing of these lenses, modification of lens properties through ultraviolet irradiation, and comparison of measured lens properties with those expected from ray trace analyses.

Wood, V. E.↗

NASA NTRS1983

Rectangular Luneburg-type lenses for integrated optics

Compact Luneburg-type lenses of rectangular outline as viewed from above have been made by thermal evaporation of As2S3 glass onto single-mode LiNbO3:Ti waveguides through suitably shaped masks and subsequent exposure of the glass to ultraviolet light. The best lenses had speeds of f/5.5 at an aperture of 10 mm and focal spots at reduced aperture about 1.2 times the diffraction-limited size. These lenses have a field of view of at least 25 degrees inside the waveguide.

Wood, V. E.↗

NASA NTRS1982

Design, fabrication and evaluation of chalcogenide glass Luneburg lenses for LiNbO3 integrated optical devices

Optical waveguide Luneburg lenses of arsenic trisulfide glass are described. The lenses are formed by thermal evaporation of As2S3 through suitably placed masks onto the surface of LiNbO3:Ti indiffused waveguides. The lenses are designed for input apertures up to 1 cm and for speeds of f/5 or better. They are designed to focus the TM sub 0 guided mode of a beam of wavelength, external to the guide, of 633 nm. The refractive index of the As2S3 films and the changes induced in the refractive index by exposure to short wavelength light were measured. Some correlation between film thickness and optical properties was noted. The short wavelength photosensitivity was used to shorten the lens focal length from the as deposited value. Lenses of rectangular shape, as viewed from above the guide, as well as conventional circular Luneburg lenses, were made. Measurements made on the lenses include thickness profile, general optical quality, focal length, quality of focal spot, and effect of ultraviolet irradiation on optical properties.

Wood, V. E.↗

NASA NTRS1981

Evaporated As2S3 Luneburg lenses for LiNbO3:Ti optical waveguides

Luneburg lenses of good quality were formed on high index optical waveguides by evaporation of arsenic trisulfide glass through simple masks. Using only two thin circular aperture masks, lenses with focal spots of a few times the diffraction limited width at f/4 were obtained. These lenses were designed for and tested at both visible (633 nm) and infrared wavelengths. Procedures for the design, fabrication, and testing of lenses of this type are described.

Busch, J. R.↗

NASA NTRS1979

Development of an Accelerated Test Design for Predicting the Service Life of the Solar Array at Mead, Nebraska

An accelerated life test is described which was developed to predict the life of the 25 kW photovoltaic array installed near Mead, Nebraska. A quantitative model for accelerating testing using multiple environmental stresses was used to develop the test design. The model accounts for the effects of thermal stress by a relation of the Arrhenius form. This relation was then corrected for the effects of nonthermal environmental stresses, such as relative humidity, atmospheric pollutants, and ultraviolet radiation. The correction factors for the nonthermal stresses included temperature-dependent exponents to account for the effects of interactions between thermal and nonthermal stresses on the rate of degradation of power output. The test conditions, measurements, and data analyses for the accelerated tests are presented. Constant-temperature, cyclic-temperature, and UV types of tests are specified, incorporating selected levels of relative humidity and chemical contamination and an imposed forward-bias current and static electric field.

Gaines, G. B.↗

NASA NTRS1979

Study of methods for direct optical address of integrated optical circuits

Methods for introducing optical information directly, without intervening recording and storage steps, into integrated optical data-processing devices are surveyed. The information is taken to be in the form of a one-dimensional variation of intensity across the beam. Physical phenomena that may be utilized are evaluated, and the most suitable presently known classes of materials for exploitation of each type of interaction are discussed. A variety of possible device configurations are suggested and general principles are outlined whereby many more device types can be generated. A simple experimental device was demonstrated and its operation was analyzed.

Wood, V. E.↗

NASA NTRS1979

Measurement Techniques and Instruments Suitable for Life-prediction Testing of Photovoltaic Arrays

The validation of a 20-year service life for low-cost photovoltaic arrays is a critical requirement in the Low-Cost Solar Array (LSA) Project. The validation is accomplished through accelerated life-prediction tests. A two-phase study was conducted to address the needs before such tests are carried out. The results and recommended techniques from the Phase 1 investigation are summarized in the appendix. Phase 2 of the study is covered in this report and consisted of experimental evaluations of three techniques selected from these recommended as a results of the Phase 1 findings. The three techniques evaluated were specular and nonspecular optical reflectometry, chemiluminescence measurements, and electric current noise measurements.

Noel, G. T.↗

NASA NTRS1979

Development of an Accelerated Test Design for Predicting the Service Life of the Solar Array at Mead, Nebraska

Potential long-term degradation modes for the two types of modules in the Mead array were determined and judgments were made as to those environmental stresses and combinations of stresses which accelerate the degradation of the power output. Hierarchical trees representing the severity of effects of stresses (test conditions) on eleven individual degradation modes were constructed and were pruned of tests judged to be nonessential. Composites of those trees were developed so that there is now one pruned tree covering eight degradation modes, another covering two degradation modes, and a third covering one degradation mode. These three composite trees form the basis for selection of test conditions in the final test plan which is now being prepared.

Gaines, G. B.↗

NASA NTRS1978

An investigation for the development of an integrated optical data preprocessor

The successful fabrication and demonstration of an integrated optical circuit designed to perform a parallel processing operation by utilizing holographic subtraction to simultaneously compare N analog signal voltages with N predetermined reference voltages is summarized. The device alleviates transmission, storage and processing loads of satellite data systems by performing, at the sensor site, some preprocessing of data taken by remote sensors. Major accomplishments in the fabrication of integrated optics components include: (1) fabrication of the first LiNbO3 waveguide geodesic lens; (2) development of techniques for polishing TIR mirrors on LiNbO3 waveguides; (3) fabrication of high efficiency metal-over-photoresist gratings for waveguide beam splitters; (4) demonstration of high S/N holographic subtraction using waveguide holograms; and (5) development of alignment techniques for fabrication of integrated optics circuits. Important developments made in integrated optics are the discovery and suggested use of holographic self-subtraction in LiNbO3, development of a mathematical description of the operating modes of the preprocessor, and the development of theories for diffraction efficiency and beam quality of two dimensional beam defined gratings.

Verber, C. M.↗

NASA NTRS1978

Measurement techniques and instruments suitable for life-prediction testing of photovoltaic arrays

Array failure modes, relevant materials property changes, and primary degradation mechanisms are discussed as a prerequisite to identifying suitable measurement techniques and instruments. Candidate techniques and instruments are identified on the basis of extensive reviews of published and unpublished information. These methods are organized in six measurement categories - chemical, electrical, optical, thermal, mechanical, and other physicals. Using specified evaluation criteria, the most promising techniques and instruments for use in life prediction tests of arrays were selected.

Noel, G. T.↗

NASA NTRS1978

Measurement requirements and techniques for degradation studies and lifetime prediction testing of photovoltaic modules

Tests of weathering and aging behavior are being developed to characterize the degradation and predict the lifetimes of low-cost photovoltaic arrays. Environmental factors which affect array performance include UV radiation, thermal energy, water, oxygen (generally involved in synergistic effects with UV radiation or high temperatures), physical stress, pollutants (oxides of nitrogen, sulfur dioxide and ozone), abrasives and dirt. A survey of photovoltaic array testing has shown the need to establish quantitative correlations between certain measurable properties (carbonyl formation, glass transition temperature, and molecular weight change) and modes of degradation and failure.

Noel, G. T.↗

NASA NTRS1978

Performance degradation mechanisms and modes in terrestrial photovoltaic arrays and technology for their diagnosis

Accelerated life-prediction test methodologies have been developed for the validation of a 20-year service life for low-cost photovoltaic arrays. Array failure modes, relevant materials property changes, and primary degradation mechanisms are discussed as a prerequisite to identifying suitable measurement techniques and instruments. Measurements must provide sufficient confidence to permit selection among alternative designs and materials and to stimulate widespread deployment of such arrays. Furthermore, the diversity of candidate materials and designs, and the variety of potential environmental stress combinations, degradation mechanisms and failure modes require that combinations of measurement techniques be identified which are suitable for the characterization of various encapsulation system-cell structure-environment combinations.

Noel, G. T.↗

NASA NTRS1977

Feasibility investigation of integrated optics Fourier transform devices

The possibility of producing an integrated optics data processing device based upon Fourier transformations or other parallel processing techniques, and the ways in which such techniques may be used to upgrade the performance of present and projected NASA systems were investigated. Activities toward this goal include; (1) production of near-diffraction-limited geodesic lenses in glass waveguides; (2) development of grinding and polishing techniques for the production of geodesic lenses in LiNbO3 waveguides; (3) development of a characterization technique for waveguide lenses; and (4) development of a theory for corrected aspheric geodesic lenses. A holographic subtraction system was devised which should be capable of rapid on-board preprocessing of a large number of parallel data channels. The principle involved is validated in three demonstrations.

Verber, C. M.↗

NASA NTRS1977

Focal characteristics of spheroidal geodesic lenses for integrated optical processing

Aspheric shaping of geodesic lenses in optical waveguides is suggested as a means for correcting spherical aberrations. The technique is complementary to the method of Spiller and Harper, in which geodesic lens aberrations are reduced by thickening the waveguiding layer in the lens region. The properties of a family of oblate-spheroidal lenses with no third-order spherical aberrations are described theoretically. Diffraction-limited performance over apertures up to one-half the full lens aperture is predicted for lenses with true f/numbers (focal length divided by useful aperture) in the range 2-12. By combining spheroidal-shaping and mode-index correction techniques, geodesic lenses free from both third- and fifth-order aberrations can be designed. These lenses show diffraction-limited performance over apertures of a centimeter or more when true f/numbers are in the range 1.5-9.5.

Vahey, D. W.↗

NASA NTRS1976

Effects of edge-rounding on geodesic lenses

A method that eliminates the need for a mathematical model is described for measuring the absolute light intensity radiated from volume chemiluminescent and fluorescent sources. This technique applies to a uniform cylindrical luminous volume, which is the geometry most often practical for the study of flowing chemiluminescent and fluorescent fluids. In this method, the necessary integration over a luminous volume is carried out experimentally, using a calibrated piston source that has as its head a disk of uniform luminosity. The relatively small total error in absolute light intensity measurements with the piston source technique represents a significant improvement over competing comparison methods. The construction of a piston source to fit the cross section of a particular cylindrical volume is straightforward, and its calibration against a standard source can be readily made while exercising normal precautions.

Wood, V. E.↗

NASA NTRS1976

Focal properties of geodesic waveguide lenses

The focal properties of uncorrected geodesic lenses in ion-exchanged glass waveguides are reported. A 13.8-mm-focal-length lens resolved beams with an angular separation of 27.6 mrad, while a 28-mm-focal-length lens resolved beams with an angular separation of only 3.3 mrad. Intensity profiles of the focal region of the former lens revealed a 40-micron spot size when the input aperture was 5 mm, and a spot size of 7.7 microns when the aperture was reduced to 1 mm. This value is close to the diffraction-limited spot size of 5.7 microns.

Verber, C. M.↗

NASA NTRS1975

Study of growth of single crystal ribbon in space

The technical feasibility is studied of growing single-crystal silicon ribbon in the space environment. Procedures are described for calculating the electromagnetic fields produced in a silicon ribbon by an rf shaping coil. The forces on the ribbon and the degree of shaping to be expected are determined. The expected steady-state temperature distribution in the ribbon is calculated in the one-dimensional approximation. Calculations on simplified models indicate, that lack of flatness of the shaped ribbon and excessive heating of the melt by the eddy currents induced by the shaping fields may pose problems. An analysis of the relative effects of various kinds of forces other than electromagnetic showed that in the space environment capillarity forces would dominate, and that the shape of the melt is thus principally determined by the shape of any solids with which it comes in contact. This suggests that ribbon may be produced simply by drawing between parallel wires. A concept is developed for a process of off-angle growth, in which the ribbon is pulled at an angle to the solidification front. Such a process promises to offer increased growth rate, better homogeneity, and thinner ribbon.

Wood, V. E.↗

NASA NTRS1973

Optical damage and internal fields in pyroelectrics.

The physical conditions under which the models of optical damage in pyroelectrics suggested by Johnston (1970) and by Amodei (1971) might be valid are described. Whether the zero-internal-field final state described by Johnston or the no-current-flow steady state of Amodei can be reached depends on the pattern of excitation and the dynamics of the damage process. In view of the small carrier diffusion lengths, the one-dimensional models generally used may not be entirely satisfactory for investigation of dynamics.

Wood, V. E.↗