CMC COMPONENTS FOR HTR DESIGN AND QUALIFICATION TESTING
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Windes, Will.
Explore the source record for details and available documents.
High Temperature Gas-cooled Reactors (HTGRs) featuring particle fuel are a very mature technology. Commercial deployment occurred in the mid-1980's with the Fort St.Vrain and Thorium Hochtemperatur Reaktor by providing electricity to the grids in the United States and West Germany, respectively. The technology was then adopted by Japan and China with the operation of the High Temperature Test Reactor in Oarai, Japan and the High Temperature Reactor (HTR-10) in China. These commercial reactors typically operate with an outlet coolant temperature of 750 deg. C to 800 deg. C. Increasing the outlet temperature of the HTGR to even higher temperatures above 900 deg. C will improve the thermodynamic efficiency of the system and enable application of a new class of gas reactor, the very high temperature reactor (VHTR), to provide process heat, electricity, and hydrogen to a broad range of industrial customers with the attendant benefits of improved energy security and reduced CO{sub 2} emissions. However, the increase in coolant outlet temperature presents a number of technical challenges associated with fuels and materials. For over a decade, the U.S. Department of Energy has been sponsoring a broad program of research and development with a goal of addressing the technical fuels and materials challenges to support deployment of a VHTR that could safely and economically operate at outlet temperatures of 750 to 950 deg. C. In summary, fuels and materials challenges exist with deploying a VHTR with an outlet temperature of 950 deg. C in the areas of structural materials, graphite and TRISO fuel. However, R and D is underway or has recently been completed suggesting that technical solutions are possible. (authors)
Explore the source record for details and available documents.
Graphite creep strain data from the irradiation creep capsule Advanced Graphite Creep-1 (AGC-1) are reported. This capsule was the first (prototype) of a series of five or six capsules planned as part of the AGC experiment, which was designed to fully characterize the effects of neutron irradiation and the radiation creep behavior of current nuclear graphite. The creep strain data and analysis are reported for the six graphite grades incorporated in the capsule. The AGC-1 capsule was irradiated in the Advanced Test Reactor at Idaho National Laboratory (INL) at approximately 700 C and to a peak dose of 7 dpa (displacements per atom). The specimen s final dose, temperature, and stress conditions have been reported by INL and were used during this analysis. The derived creep coefficients (K) were calculated for each grade and were found to compare well to literature data for the creep coefficient, even under the wide range of AGC-1 specimen temperatures. Comparisons were made between AGC-1 data and historical grade data for creep coefficients.
The aim of the research presented here was to identify the chemical form of 14 C in irradiated graphite. A greater understanding of the chemical form of this longest-lived isotope in irradiated graphite will inform not only management of legacy waste, but also development of next generation gas-cooled reactors. Approximately 250,000 metric tons of irradiated graphite waste exists worldwide, with the largest single quantity originating in the Magnox and AGR reactors of UK. The waste quantity is expected to increase with decommissioning of Generation II reactors and deployment of Generation I gas-cooled, graphite moderated reactors. Of greatest concern for long-term disposal of irradiated graphite is carbon-14 14 C, with a half-life of 5730 years.
Current candidate graphite grades for the core structures of NGNP include grades NBG-17, NBG-18, PCEA and IG-430. Both NBG-17 and NBG-18 are manufactured using pitch coke, and are vibrationally molded. These medium grain products are produced by SGL Carbon SAS (France). Tayo Tanso (Japan) produces IG-430 which is a petroleum coke, isostatically molded, nuclear grade graphite. And PCEA is a medium grain, extruded graphite produced by UCAR Carbon Co. (USA) from petroleum coke. An experimental program has been initiated to develop physical and mechanical properties data for these current candidate graphites. The results will be judged against the requirements for nuclear grade graphites set forth in ASTM standard D 7219-05 "Standard Specification for Isotropic and Near-isotropic Nuclear Graphites". Physical properties data including thermal conductivity and coefficient of thermal expansion, and mechanical properties data including tensile, compressive and flexural strengths will be obtained using the established test methods covered in D-7219 and ASTM C 781-02 "Standard Practice for Testing Graphite and Boronated Graphite Components for High-Temperature Gas-Cooled Nuclear Reactors". Various factors known to effect the properties of graphites will be investigated. These include specimen size, spatial location within a graphite billet, specimen orientation (ag and wg) within a billet, and billet-to-billet variations. The current status of the materials characterization program is reported herein. To date billets of the four graphite grades have been procured, and detailed cut up plans for obtaining the various specimens have been prepared. Particular attention has been given to the traceability of each specimen to its spatial location and orientation within a billet.
Currently, two composites types are being developed for incore application: carbon fiber carbon composite (CFC), and silicon carbide fiber composite (SiC/SiC.) Irradiation effects studies have been carried out over the past few decades yielding radiation-tolerant CFC's and a composite of SiC/SiC with no apparent degradation in mechanical properties to very high neutron exposure. While CFC's can be engineered with significantly higher thermal conductivity, and a slight advantage in manufacturability than SiC/SiC, they do have a neutron irradiation-limited lifetime. The SiC composite, while possessing lower thermal conductivity (especially following irradiation), appears to have mechanical properties insensitive to irradiation. Both materials are currently being produced to sizes much larger than that considered for nuclear application. In addition to materials aspects, results of programs focusing on practical aspects of deploying composites for near-term reactors will be discussed. In particular, significant progress has been made in the fabrication, testing, and qualification of composite gas-cooled reactor control rod sheaths and the ASTM standardization required for eventual qualification.
Explore the source record for details and available documents.