Engineering topics
Wilson, Scott
Publications and source records attributed to Wilson, Scott.
NASA Proof-of-Concept 1-W Stirling Convertor Development for Small RPS
Low power Stirling convertors are being developed at NASA Glenn Research Center (GRC) to provide future small spacecraft with electrical power by converting heat from one or more Light Weight Radioisotope Heater Units (LWRHU). An initial design converts multiple watts of heat to one watt of electrical power output using a Stirling convertor. A variety of mission concepts have been studied by NASA and the U.S. Department of Energy (DOE) that would utilize low power Radioisotope Power Systems (RPS) for probes, landers, rovers, and repeaters. These missions would contain science instruments distributed across planetary surfaces or near objects of interest where solar flux is insufficient for using solar cells. Landers could be used to provide data such as, radiation, temperature, pressure, seismic activity, and other surface measurements for planetary science and to inform future mission planners. The studies propose using fractional versions of the General Purpose Heat Source (GPHS) or multiple LWRHUs to heat power conversion technologies for science instruments and communication. Dynamic power systems are capable of higher conversion efficiencies, which could enable equal power using less fuel or more power using equal fuel, when compared to less efficient static power conversion technologies. Providing spacecraft with more power would decrease duty cycling of basic functions and, therefore, increase the quality and abundance of science data. Efforts to develop the concept have focused on maturation of a 1-We (1-watt electrical) convertor and controller design and performance evaluation of an evacuated metal foil insulation. A proof-of-concept 1-We convertor, controller, and evacuated metal foil insulation package have been fabricated and are undergoing characterization testing. The current status, findings, and path forward for the effort are explained in this paper.
Overview of Multi-Layer Metal Insulation Development for Small Stirling Convertors at NASA GRC
The small Stirling convertor currently under development at the NASA Glenn Research Center (GRC) is designed to produce one watt of electrical power from eight watts of heat. Previous radioisotope power systems (RPS) made use of the General-Purpose Heat Source (GPHS) which produces 250 watts of heat but is unsuitable for a one-watt Stirling convertor. The only heat source available is the Light-Weight Radioisotope Heating Unit (LWRHU) which produces one watt of heat and is primarily used to provide heat to electronics and instrumentation to maintain their appropriate operating temperature. Unfortunately, the LWRHU has a heat flux of 272 W/m-squared (watts per square meter) compared to the GPHS heat flux of 6000 W/m-squared which greatly increases the demands on the insulation to ensure that enough of the heat produced is available to the convertor and not lost to the environment. An analysis was performed that showed that the insulation must have a thermal conductivity of 0.005 W/m squared -K (watts per square meter per Kelvin) or better for the system to function. A multi-layer metal insulation package was designed and a prototype was fabricated and tested to investigate the feasibility of this design. The prototype did not meet the requirements; however, the improved thermal model generated using the test data will allow for a second iteration to be developed that has a much higher confidence and meets the performance requirements.
Small Stirling Technology Exploration Power for Future Space Science Missions
High efficiency dynamic Radioisotope Power Systems (RPS) could be mission enabling for low power space applications such as small probes, landers rovers, and communication repeaters. These applications would contain science instruments and be distributed across planetary surfaces or near objects of interest where solar flux is insufficient for using solar cells. Small RPS could be used to provide power for sensing radiation, temperature, pressure, seismic activity, and other measurements of interest to planetary scientists. Small RPS would use fractional versions of the General Purpose Heat Source (GPHS) or Light Weight Radioisotope Heater Units (LWRHU), to heat power conversion technologies. Dynamic power systems are capable of three to four times higher conversion efficiency compared to static power conversion technologies, and would provide an equal amount of power using less fuel or more power using an equal amount of fuel. Providing spacecraft with more power could decrease duty cycling of basic functions and, therefore, increase the quality and abundance of science data. NASA Glenn Research Center (GRC) is developing a low power dynamic RPS that would convert heat from multiple LWRHU to one watt of usable direct current electric power for spacecraft instrumentation and communication. The power system could be used to charge batteries or capacitors for higher power burst usage. The initial design, called Small Stirling Technology Exploration Power (smallSTEP), is around 3 kg, 11 cm diameter X 32 cm long, and converts 8 watts of heat to one watt of electricity using a Stirling convertor. This low power conversion system represents a new class of RPS with power levels two orders of magnitude lower than prototypes currently being developed for space applications under NASA contracts. Development of the 1-watt RPS includes maturation of convertor and controller designs, performance evaluation of an evacuated metal foil insulation, and development of system interfaces. Initial demonstration of the subsystems has been completed in a laboratory environment and a higher fidelity system is being pursued for demonstration in relevant environments for use on small spacecraft needed to carry out future space science missions.
Maturation of Dynamic Power Convertors for Radioisotope Power Systems
Dynamic Radioisotope Power Systems (DRPS) are being developed by NASA's RPS Program in collaboration with the U.S. Department of Energy (DOE) for space science and exploration missions. A development effort is currently underway to mature dynamic power convertors for infusion into a potential future flight generator. This convertor maturation effort was formulated by the RPS Program at NASA Headquarters based on successful maturation models and utilizes expertise from agency technology and mission centers to support requirements development and technology assessments. The effort is being executed by Glenn Research Center's Dynamic Radioisotope Power Systems (DRPS) project and the Thermal Energy Conversion Branch. The Dynamic Power Convertor (DPC) contracts consist of three phases to enable design, fabrication, and independent assessment after delivery to the government. The contracts are intended to gather data on candidate dynamic conversion technologies to fill knowledge gaps, support assessments of dynamic conversion technologies, and elicit generator requirements. The SRG-110 (Stirling Radioisotope Generator) and ASRG (Advanced Stirling Radioisotope Generator) flight development projects provided Stirling convertor demonstration units and engineering models to verify and validate convertors against performance specifications and mission requirements. These units utilize temperature resistance materials and non-contacting bearings to demonstrate wear-free, long-life operation. This maturation effort builds on past lessons learned and new requirements focused on demonstrating convertor robustness to critical environments meant to stress key aspects of each convertor within the margins of the design. This effort seeks to realize the full potential of dynamic power conversion technologies for NASA's space science and exploration missions.
Maturation of Dynamic Power Convertors for Radioisotope Power Systems
Dynamic Radioisotope Power Systems (DRPS) are being developed by NASA’s Radioisotope Power Systems (RPS) Program in collaboration with the U.S. Department of Energy (DOE) for space science and exploration missions. A development effort is currently underway to mature dynamic power convertors for infusion into a potential future flight generator. This convertor maturation effort was formulated by the RPS Program at NASA Headquarters based on successful maturation models and utilizes expertise from agency’s technology and mission centers to support requirements development and technology assessments. The effort is being executed by Glenn Research Center’s (GRC) DRPS Project and the Thermal Energy Conversion Branch. The Dynamic Power Convertor (DPC) contracts consist of three phases to enable design, fabrication, and independent assessment of prototypes after delivery to the government. The contracts are intended to gather data on candidate dynamic conversion technologies to fill knowledge gaps, support assessments of dynamic conversion technologies, and elicit generator requirements. The 110-watt Stirling Radioisotope Generator (SRG-110) and Advanced Stirling Radioisotope Generator (ASRG) flight development projects provided Stirling convertor demonstration units and engineering models to verify and validate convertors against performance specifications and mission requirements. These units utilize temperature resistant materials and non-contacting bearings to demonstrate wear-free, long-life operation. This maturation effort builds on past lessons-learned and new requirements focused on demonstrating convertor robustness to critical environments meant to stress key aspects of each convertor within the margins of the design. This effort seeks to realize the full potential of dynamic power conversion technologies for NASA’s space science and exploration missions.
Dynamic Power Convertor Development for Radioisotope Power Systems at NASA Glenn Research Center
The Thermal Energy Conversion Branch at NASA Glenn Research Center is supporting the development of high-efficiency power convertors for use in radioisotope power systems (RPS). Significant progress was made toward such a system that utilized Stirling conversion during the 2001 to 2015 timeframe. Flight development of the Advanced Stirling Radioisotope Generator (ASRG) was canceled in 2013 by the U.S. Department of Energy (DOE) and NASA Headquarters primarily due to budget constraints, and the Advanced Stirling Convertor (ASC) technology contract was subsequently concluded in 2015. A new chapter of technology development has recently been initiated by the NASA RPS Program. This effort is considering all dynamic power convertor options, such as Stirling and Brayton cycles. Four convertor development contracts supporting this effort were awarded in 2017. The awarded contracts include two free-piston Stirling, one thermoacoustic Stirling, and one turbo-Brayton design. The technology development contracts each consist of up to three phases: design, fabrication, and test. As of May 2018, all contracts have completed the design phase, and each underwent a design review with an independent review board. Three of the contracts are planned to execute the phase 2 option for fabrication. Convertors manifesting from these development efforts will then undergo independent validation and verification (IV and V) at NASA facilities, which will consist of convertor performance and RPS viability demonstrations. Example tests include launch vibration simulation, performance mapping over the environmental temperature range, and static acceleration exposure. In parallel with this renewed development effort, Glenn is still demonstrating free-piston Stirling convertor technology using assets from previous projects. The Stirling Research Laboratory (SRL) is still operating several convertors from previous development projects, which have similarities and relevance to current contract designs. Four of these are flexure-bearing based and another six are gas bearing based. One of the flexure-bearing convertors has accumulated over 110,000 h of operation and holds the current record for maintenance-free heat-engine run time. Another flexure-bearing convertor was recently manually shut down after 105,620 h of operation, then disassembled and inspected. This inspection produced a wealth of information about the effects of this amount of run time on the technology's components. One of the engineering unit flexure-bearing convertors recently underwent a launch simulation vibration test, a static acceleration exposure up to 20 g, and was then placed on extended operation. Among the gas-bearing convertors, the longest running unit has accumulated over 70,000 h of operation. Four high-fidelity gas-bearing convertors from the ASRG project are still operating continuously for which the longest run time has reached 28,000 h.
1-Watt Radioisotope Power System for Small Spacecraft
A variety of mission concepts have been studied by NASA and the U. S. Department of Energy that would utilize low power Radioisotope Power Systems (RPS) for small probes, landers, rovers, and communication repeaters. These missions would contain science measuring instruments that could be distributed across planetary surfaces for operation in temporarily or permanently shadowed regions. High efficiency dynamic RPS could be mission enabling for science measurements on the moon, such as collecting real-time, event-based, or cumulative space radiation measurements including primary galactic cosmic rays (GCR), solar particle events (SPE), and secondary particles liberated during atmospheric and/or surface reactions. Small RPS would use fractional versions of the General Purpose Heat Source (GPHS) or Light Weight Radioisotope Heater Units (LWRHU), to heat the power conversion technologies. Capable of three to four times higher conversion efficiency than static technologies, dynamic RPS would provide an equal amount of power using less fuel or more power using an equal amount of fuel. Providing spacecraft with more power could decrease duty cycling of basic functions and increase the quality and abundance of science data. Low power Stirling convertors are being developed at NASA Glenn Research Center (GRC) to provide future micro spacecraft with electrical power by converting heat from one or more LWRHUs. An initial concept would convert eight Watts of heat to one Watt of electrical power output for science instruments and communication. The initial design, called Small Stirling Technology Exploration Power (smallSTEP), is 11 cm diameter X 32 cm long, weighs around 3 kg, and could be used to charge batteries or capacitors for higher power burst usage. Development of the 1-watt RPS includes maturation of a Stirling engine and linear alternator, an electronics controller, and an evacuated metal foil insulation package. Test hardware and facilities are being prepared for initial demonstration of the subassemblies in a laboratory environment.
Dynamic Power Convertor Development for Radioisotope Power Systems at NASA GRC
The Thermal Energy Conversion Branch at NASA Glenn Research Center (GRC) is supporting the development of high-efficiency power convertors in support of Radioisotope Power System (RPS) development. Significant progress was made towards such a system that utilized Stirling conversion machines during the 2001 to 2015 timeframe. Flight development of the Advanced Stirling Radioisotope Generator (ASRG) was cancelled in 2013 by the Department of Energy (DOE) and NASA Headquarters primarily due to budget constraints, and the Advanced Stirling Convertor (ASC) technology contract was subsequently concluded in 2015. A new chapter of technology development has recently been initiated by the NASA RPS Program. This new effort is considering all dynamic power convertor options, such as Stirling and Brayton cycles. Four convertor development contracts supporting this effort were awarded in 2017. The awarded contracts include two free-piston Stirling, one thermoacoustic Stirling, and one turbo-Brayton designs. The technology development contracts each consist of up to three phases: Design, Fabricate, and Test. As of May 2018, all contracts have completed the Design Phase, and each underwent a design review with an independent review board. Two of the contracts have been awarded the Phase 2 option for fabrication. Convertors manifesting from these development efforts will then undergo independent validation and verification at NASA facilities, which will consist of convertor performance and RPS viability demonstrations. Example tests include launch vibration simulation, performance mapping over the environmental temperature range, and static acceleration exposure. In parallel with this renewed development effort, NASA GRC is still demonstrating free-piston Stirling convertor technology using assets from previous projects. The Stirling Research Laboratory (SRL) is still operating 10 convertors from previous development projects. Four of which are flexure-bearing based, and the other six are gas-bearing based. One of the flexure-bearing convertors has accumulated over 110,000 hours of operation, and holds the current maintenance-free heat-engine run-time record. Another flexure-bearing convertor was recently manually shutdown after 105,620 hours of operation, then disassembled and inspected. This inspection produced a wealth of information about the effects of this amount of runtime on the technology's components. One of the engineering unit flexure-bearing convertors recently underwent launch simulation vibration test, a static acceleration exposure up to 20 g, and was then placed on extended operation. Amongst the gas-bearing convertors, the longest running unit has accumulated over 70,000 hours of operation. Four high-fidelity gas-bearing convertors from the ASRG project are still operating continuously, for which the longest runtime has reached 26,000 hours.
NASA Low Power Stirling Convertor for Small Landers, Probes, and Rovers Operating in Darkness
A variety of mission concepts have been studied by NASA and the U. S. Department of Energy that would utilize low power Radioisotope Power Systems (RPS) for landers, probes, and rovers. These missions would contain science measuring instruments distributed across planetary surfaces or near objects of interest where solar flux is insufficient for using solar cells. Landers could be used to provide data like wind, temperature, pressure, seismic activity, and other planetary measurements to mission planners or future explorers. The studies proposed using fractional versions of the General Purpose Heat Source (GPHS) or multiple Light Weight Radioisotope Heater Units (LWRHU) to heat power conversion technologies for science instruments and communication. Dynamic power systems are capable of higher conversion efficiencies, which could enable equal power using less fuel or more power using equal fuel, when compared to less efficient static power conversion technologies. Providing spacecraft with more power would decrease duty cycling of basic functions and, therefore, increase the quality and abundance of science data. Low power Stirling convertors are being developed at NASA Glenn Research Center (GRC) to provide future micro spacecraft with electrical power by converting heat from one or more LWRHUs. An initial design converts multiple Watts of heat to one Watt of electrical power output using a Stirling convertor. Development of the concept includes maturation of convertor and controller designs, performance evaluation of an evacuated metal foil insulation, and development of system interfaces.
Status of Dynamic Power Convertor Development for RPS at NASA GRC
NASA's dynamic power convertor development in support of high-efficiency RPS is progressing as planned, and shows promise. Ongoing research utilizing existing hardware supports viability of dynamic power conversion for RPS.
Dynamic Radioisotope Power Systems: Convertor Development at NASA GRC
NASA's dynamic power convertor development in support of high-efficiency RPS is progressing as planned, and shows promise. This presentation gives dynamic conversion power system background, development path, and key convertor performance goals. It also gives information on the Flexure Isotope Stirling Convertor, Turbo-Brayton Convertor, Thermo-Acoustic Power Convertor, Sunpower Robust Stirling Convertor, Stirling Convertor Extended Operation, TDC #14 Disassembly and Inspection, and Launch Vibration Exposure on SES #2.
Advanced Stirling Convertor (ASC) Technology Maturation
The Advanced Stirling Convertor (ASC) development effort was initiated by NASA Glenn Research Center with contractor Sunpower, Inc., to develop high-efficiency thermal-to-electric power conversion technology for NASA Radioisotope Power Systems (RPSs). Early successful performance demonstrations led to the expansion of the project as well as adoption of the technology by the Department of Energy (DOE) and system integration contractor Lockheed Martin Space Systems Company as part of the Advanced Stirling Radioisotope Generator (ASRG) flight project. The ASRG integrates a pair of ASCs to convert the heat from a pair of General Purpose Heat Source (GPHS) modules into electrical power. The expanded NASA ASC effort included development of several generations of ASC prototypes or engineering units to help prepare the ASC technology and Sunpower for flight implementation. Sunpower later had two parallel contracts allowing the last of the NASA engineering units called ASC-E3 to serve as pathfinders for the ASC-F flight convertors being built for DOE. The ASC-E3 convertors utilized the ASC-F flight specifications and were built using the ASC-F design and process documentation. Shortly after the first ASC-F pair achieved initial operation, due to budget constraints, the DOE ASRG flight development contract was terminated. NASA continues to invest in the development of Stirling RPS technology including continued production of the ASC-E3 convertors, seven of which have been delivered with one additional unit in production. Starting in fiscal year 2015, Stirling Convertor Technology Maturation has been reorganized as an element of the RPS Stirling Cycle Technology Development (SCTD) Project and long-term plans for continued Stirling technology advancement are in reformulation. This paper provides a status on the ASC project, an overview of advancements made in the design and production of the ASC at Sunpower, and a summary of acceptance tests, reliability tests, and tactical tests at NASA Glenn that demonstrate the capabilities of the ASC.
Advanced Stirling Convertor (ASC) Technology Maturation
The Advanced Stirling Convertor (ASC) development effort was initiated by NASA Glenn Research Center (GRC) with contractor Sunpower Inc. to develop high efficiency thermal-to-electric power conversion technology for NASA Radioisotope Power Systems. Early successful performance demonstrations led to the expansion of the project as well as adoption of the technology by the Department of Energy (DOE) and system integration contractor Lockheed Martin Space Systems Company as part of the Advanced Stirling Radioisotope Generator (ASRG) flight project. The ASRG integrates a pair of ASCs to convert the heat from a pair of General Purpose Heat Source (GPHS) modules into electrical power. The expanded NASA ASC effort included development of several generations of ASC prototypes or Engineering Units to help prepare the ASC technology and Sunpower for flight implementation. Sunpower later had two parallel contracts allowing the last of the NASA Engineering Units called ASC-E3 to serve as pathfinders for the ASC-F flight convertors being built for DOE. The ASC-E3 convertors utilized the ASC-F flight specifications and were built using the ASC-F design and process documentation. Shortly after the first ASC-F Pair achieved initial operation, due to budget constraints, the DOE ASRG flight development contract was terminated. NASA continues to invest in the development of Stirling RPS technology including continued production of the ASC-E3 convertors, seven of which have been delivered with one additional unit in production. Starting in FY2015, Stirling Convertor Technology Maturation has been reorganized as an element of the RPS Stirling Cycle Technology Development (SCTD) Project and long-term plans for continued Stirling technology advancement are in reformulation. This paper provides a status on the ASC project, an overview of advancements made in the design and production of the ASC at Sunpower, and a summary of acceptance tests, reliability tests, and tactical tests at NASA GRC that demonstrate the capabilities of the ASC.
Advanced Stirling Convertor (ASC) Development for NASA RPS
Sunpower's Advanced Stirling Convertor (ASC) initiated development under contract to the NASA Glenn Research Center (GRC) and after a series of successful demonstrations, the ASC began transitioning from a technology development project to flight development project. The ASC has very high power conversion efficiency making it attractive for future Radioisotope Power Systems (RPS) in order to make best use of the low plutonium-238 fuel inventory in the U.S. In recent years, the ASC became part of the NASA-Department of Energy Advanced Stirling Radioisotope Generator (ASRG) Integrated Project. Sunpower held two parallel contracts to produce ASC convertors, one with the Department of Energy/Lockheed Martin to produce the ASC-F flight convertors, and one with NASA GRC for the production of ASC-E3 engineering units, the initial units of which served as production pathfinders. The integrated ASC technical team successfully overcame various technical challenges that led to the completion and delivery of the first two pairs of flight-like ASC-E3 by 2013. However, in late Fall 2013, the DOE initiated termination of the Lockheed Martin ASRG flight development contract driven primarily by budget constraints. NASA continues to recognize the importance of high efficiency ASC power conversion for RPS and continues investment in the technology including the continuation of ASC-E3 production at Sunpower and the assembly of the ASRG Engineering Unit #2. This paper provides a summary of ASC technical accomplishments, overview of tests at GRC, plans for continued ASC production at Sunpower, and status of Stirling technology development.
Advanced Stirling Convertor (ASC-E2) Performance Testing at NASA Glenn Research Center
The National Aeronautics and Space Administration (NASA) Glenn Research Center (GRC) has been supporting development of the Advanced Stirling Radioisotope Generator (ASRG) since 2006. A key element of the ASRG Project is providing life, reliability, and performance testing of the Advanced Stirling Convertor (ASC). For this purpose, four pairs of ASCs capable of operating to 850 C and designated with the model number ASC-E2, were delivered by Sunpower of Athens, Ohio, to GRC in 2010. The ASC-E2s underwent a series of tests that included workmanship vibration testing, performance mapping, and extended operation. Workmanship vibration testing was performed following fabrication of each convertor to verify proper hardware build. Performance mapping consisted of operating each convertor at various conditions representing the range expected during a mission. Included were conditions representing beginning-of-mission (BOM), end-of-mission (EOM), and fueling. This same series of tests was performed by Sunpower prior to ASC-E2 delivery. The data generated during the GRC test were compared to performance before delivery. Extended operation consisted of a 500-hr period of operation with conditions maintained at the BOM point. This was performed to demonstrate steady convertor performance following performance mapping. Following this initial 500-hr period, the ASC-E2s will continue extended operation, controller development and special durability testing, during which the goal is to accumulate tens of thousands of hours of operation. Data collected during extended operation will support reliability analysis. Performance data from these tests is summarized in this paper.
Advanced Stirling Convertor (ASC-E2) Performance Testing at NASA Glenn Research Center
The National Aeronautics and Space Administration (NASA) Glenn Research Center (GRC) has been supporting development of the Advanced Stirling Radioisotope Generator (ASRG) since 2006. A key element of the ASRG Project is providing life, reliability, and performance testing of the Advanced Stirling Convertor (ASC). For this purpose, four pairs of ASCs capable of operating to 850 C and designated with the model number ASC-E2, were delivered by Sunpower of Athens, OH, to GRC in 2010. The ASC-E2s underwent a series of tests that included workmanship vibration testing, performance mapping, and extended operation. Workmanship vibration testing was performed following fabrication of each convertor to verify proper hardware build. Performance mapping consisted of operating each convertor at various conditions representing the range expected during a mission. Included were conditions representing beginning-of-mission (BOM), end-of-mission (EOM), and fueling. This same series of tests was performed by Sunpower prior to ASC-E2 delivery. The data generated during the GRC test were compared to performance before delivery. Extended operation consisted of a 500-hour period of operation with conditions maintained at the BOM point. This was performed to demonstrate steady convertor performance following performance mapping. Following this initial 500-hour period, the ASC-E2s will continue extended operation, controller development and special durability testing, during which the goal is to accumulate tens of thousands of hours of operation. Data collected during extended operation will support reliability analysis. Performance data from these tests is summarized in this paper.
On the Need for Multidimensional Stirling Analysis
Contents include the following: Dual opposed convertors. High efficiency. Low mass space power. One-dimensional analysis. Fast computation. Design optimizations are easily done. Need for multidimensional modeling. Axisymmetric simulation. Flow characteristics. Low mach number. Laminar, transitional, and turbulent flow. Conjugate heat transfer. Third order analysis. Recent whole engine modeling. Regenerator geometry. Turbulence modeling. Flat head heater not 1-D. Empirical coefficients needed. Experiment design. Flow distribution. Sensor placement. Calibration. Validation.