Engineering Papers⌕ Search

Engineering topics

Wilson, Mahlon Scott

Publications and source records attributed to Wilson, Mahlon Scott.

Microwatt fuel cell stack

A microwatt fuel cell stack that demonstrates a wide range temperature tolerance, low reactant cross-over and leakage, low internal leakage current, and/or effective water transport is disclosed. Both H 2 and O 2 may be supplied directly to the fuel cell stack (i.e., dead-ended). One-piece gas diffusion electrodes (GDEs) may serve as both the active electrode and manifold port. Water removal may be accomplished by permeation through the membrane to “fins” exposed by notches in the bipolar plates and gaskets.

Wilson, Mahlon Scott↗

ASTM D03 Workshop: Developing a Hydrogen Contamination Detector Analyzer [Slides]

Non-hydrogen constituents in the fuel steam can cause irreversible damage to FC systems and therefore should be avoided. The objectives are: 1. Develop a low-cost fast response device (analyzer) to measure impurities in a dry hydrogen fuel stream at or above the SAE J2719 levels, 2. Develop understanding of a working mechanism and improve the analyzer by identifying the best materials and their configuration, and 3. Test the analyzer in real-world environments.

42 ENGINEERING↗

High Performing and Durable Pyrophosphate Based Composite Membranes for Intermediate Temperature Fuel Cells [Slides]

Objective: Develop a novel proton conducting electrolyte operating at >200°C with conductivity σ ≥ 100 mScm –1 and RH < 1%. Fabrication of membranes of less than 40μm thickness while retaining high conductivity will result in ASR <0.04 Ωcm 2 . Evaluate membrane durability in terms of crossover, shorting resistance, and open circuit voltage, as well as against temperature cycling. Relevance: Operating FCs in the intermediate temperature range has the potential to greatly reduce cost and simplify water and thermal management. This effort requires novel materials and approaches to meet DOE membrane performance and durability targets. MPP/Polymer composite membranes show promise in early development for application in IT-FCs for transportation applications. Approach: We have demonstrated that both cation dopants and phosphate precursor influence MPP conductivity and identified the most promising MPP compositions for membrane fabrication. The ceramic MPP materials are fabricated as a composite membrane in a 90:10 wt% ratio with Nafion. We have modified our membrane fabrication procedure to improve the density of our membranes. Accomplishments: We demonstrated through-plane membrane conductivity of 95mScm -1 at T > 200°C and RH<0.04bar with a thickness 50μm. We demonstrated FC performance up to 94hrs at 220°C and <1% RH with a 50μm thick membrane exhibiting an OCV of 0.98V and ASR of 0.08 Wcm 2 . Future work: Further decrease in ASR is expected by decreasing the membrane thickness to <40μm. ITPP with higher P:M ratio will be used to increase the conductivity of the starting material. Long term durability will be assessed against DOE technical targets

30 DIRECT ENERGY CONVERSION↗

Microwatt Fuel Cell for Long-Term and Wide Ambient Temperature Range Operation

A small microwatt fuel cell stack and system was designed, fabricated, and tested for passive operation with pure H 2 and O 2 to provide continuous power for multiple decades with uncontrolled fluctuating ambient conditions. The stack was designed to operate with dead ended gas flows with water removal via passive membrane diffusion to notches in the bipolar plates. Additional requirements for decades long operation is minimizing H 2 and O 2 consumption, specifically membrane cross-over; to minimize cross-over, stacks were built with layered membranes of 100 µm and 400 µm. Here, the stack spatial water concentration level was monitored during operation by in situ neutron imaging to evaluate the passive water management design. Operation was verified by testing at temperatures ranging from -55 °C to 80 °C, including periodic pulses in power.

08 HYDROGEN↗

Determining Water Content and Distribution in PEMFCs to Predict Aging While in Storage

Proton membrane exchange fuel cells (PEMFCs) have the potential to be long term backup power sources with a startup time on the order of seconds. Water management is the key issue in being able to successfully store PEMFCs for extended periods of time. In this work custom made PEMFCs were humidified at various relative humidities (%RH) and subsequently stored for different lengths of time. The fuel cell’s water content was then imaged at the National Institute of Standards and Technology (NIST) neutron imaging facility. In conclusion, the cells’ startup performances were measured simulating quick startup conditions to define the effect of different water distributions.

25 ENERGY STORAGE↗