Engineering Papers⌕ Search

Engineering topics

Wilson, C.

Publications and source records attributed to Wilson, C..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Fabrication of the Fermilab Pre-Series Cold Mass for the HL-LHC Accelerator Upgrade Project

Fermilab is fabricating ten full length cold masses for the high-luminosity Large Hadron Collider Accelerator Upgrade Project (HL-LHC AUP). One practice assembly and one pre-series assembly have been completed. Here this paper summarizes the construction details. Topics include incoming inspection, bus assembly, component machining, shell forming, beam tube insertion, bus expansion loop installation, instrumentation installation, electrical testing, heat exchanger installation and final assembly welding. In-process surveys, alignment measurements and testing are presented and explained. Problems encountered during construction and their solutions are discussed.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Using additive manufacturing technologies in high-field accelerator magnet coils

Recent advances with additive manufacturing (AM) technologies using various materials allow them to be considered for the manufacture of precise and complicated metal parts of the magnet coils of high field accelerator magnets from aluminum bronze, titanium alloy, stainless steel, etc. The 3D printing technology is also being used to fabricate prototype models of real parts to test and optimize their geometry. This paper discusses the designs of the complex stress-management coil parts developed at Fermilab, their fabrication using AM technologies, and quality control methods and results.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Experimental quantification of the impact of heterogeneous mix on thermonuclear burn

In inertial confinement fusion, deuterium–tritium (DT) fuel is brought to densities and temperatures where fusion ignition occurs. However, mixing of the ablator material into the fuel may prevent ignition by diluting and cooling the fuel. MARBLE experiments at the National Ignition Facility provide new insight into how mixing affects thermonuclear burn. These experiments use laser-driven capsules containing deuterated plastic foam and tritium gas. Embedded within the foam are voids of known sizes and locations, which control the degree of heterogeneity of the fuel. Initially, the reactants are separated, with tritium concentrated in the voids and deuterium in the foam. During the implosion, mixing occurs between the foam and gas materials, leading to DT fusion reactions in the mixed region. Here, it is shown that by measuring the ratios of DT and deuterium–deuterium neutron yields for different macropore sizes and gas compositions, the effects of mix heterogeneity on thermonuclear burn may be quantified, supporting an improved understanding of these effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

A portable X-pinch design for x-ray diagnostics of warm dense matter

We describe the design and x-ray emission properties (temporal, spatial, and spectral) of Dry Pinch I, a portable X-pinch driver developed at Imperial College London. Dry Pinch I is a direct capacitor discharge device, 300 × 300 × 700 mm3 in size and ∼50 kg in mass, that can be used as an external driver for x-ray diagnostics in high-energy-density physics experiments. Among key findings, the device is shown to reliably produce 1.1 ± 0.3 ns long x-ray bursts that couple ∼50 mJ of energy into photon energies from 1 to 10 keV. The average shot-to-shot jitter of these bursts is found to be 10 ± 4.6 ns using a combination of x-ray and current diagnostics. The spatial extent of the x-ray hot spot from which the radiation emanates agrees with previously published results for X-pinches—suggesting a spot size of 10 ± 6 µm in the soft energy region (1–10 keV) and 190 ± 100 µm in the hard energy region (>10 keV). These characteristics mean that Dry Pinch I is ideally suited for use as a probe in experiments driven in the laboratory or at external facilities when more conventional sources of probing radiation are not available. At the same time, this is also the first detailed investigation of an X-pinch operating reliably at current rise rates of less than 1 kA/ns.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Large Methane Emissions From the Pantanal During Rising Water‐Levels Revealed by Regularly Measured Lower Troposphere CH 4 Profiles

Abstract The Pantanal region of Brazil is the largest seasonally flooded tropical grassland and, according to local chamber measurements, a substantial CH 4 source. CH 4 emissions from wetlands have recently become of heightened interest because global atmospheric 13 CH 4 data indicate they may contribute to the resumption of atmospheric CH 4 growth since 2007. We have regularly measured vertical atmospheric profiles for 2 years in the center of the Pantanal with the objectives to obtain an estimate of CH 4 emissions using an atmospheric approach, and provide information about flux seasonality and its relation to controlling factors. Boundary layer‐free troposphere differences observed in the Pantanal are large compared to other wetlands. Total emissions based on a planetary boundary layer budgeting technique are 2.0–2.8 TgCH 4 yr −1 (maximum flux ∼0.4 gCH 4 m −2 d −1 ) while those based on a Bayesian inversion using an atmospheric transport model are ∼3.3 TgCH 4 yr −1 . Compared to recent estimates for Amazonia (∼41 ± 3 TgCH 4 yr −1 , maximum flux ∼0.3 gCH 4 m −2 d −1 ) these emissions are not that large. Our Pantanal data suggest a clear flux seasonality with CH 4 being released in large amounts just after water levels begin to rise again after minimum levels have been reached. CH 4 emissions decline substantially once the maximum water level has been reached. While predictions with prognostic wetland CH 4 emission models agree well with the magnitude of the fluxes, they disagree with the phasing. Our approach shows promise for detecting and understanding longer‐term trends in CH 4 emissions and the potential for future wetlands CH 4 emissions climate feedbacks.

Gloor, M.↗
DOE OSTI2020

The CLAS12 superconducting magnets

As part of the Jefferson Lab 12 GeV upgrade, the Hall B CLAS12 system requires two superconducting iron-free magnets — a torus and a solenoid. The physics requirements to maximize space for the detectors guided engineers toward particular coil designs for each of the magnets which, in turn, led to the choice of using conduction cooling. The torus consists of 6 trapezoidal NbTi coils connected in series with an operating current of 3770 A. The solenoid is an actively shielded 5 T magnet consisting of 5 NbTi coils connected in series operating at 2416 A. Within the hall, the two magnets are located in close proximity to each other and are completely covered both inside and outside by particle detectors. Stringent size limitations were imposed for both magnets and introduced particular design and fabrication challenges. This paper describes the design, construction, installation, commissioning, and operation of the two magnets.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2018

Blind Intercomparison of Nuclear Accident Dosimetry using the Flattop Reactor at NCERC

The purpose of this exercise was to continue United States, United Kingdom, and France collaborative activities performing Nuclear Accident Dosimetry intercomparison. IER 148 was the inaugural intercomparison exercise using the Godiva reactor at the DAF. In contrast to IER 148, in the current exercise participants were “blind” to the known doses during the exercise, to simulate the dosimetry response to a real criticality incident. This document is the Final Exercise (CED-x) Report for IER-253, “International Intercomparison Exercise for Nuclear Accident Dosimetry at the DAF Using Flattop.” The report describes the structure and results of the exercise consisting of two irradiations. The details of all dosimetry elements and their placement in proximity to Flattop on support stands or phantoms was unknown to participating laboratories. The participating laboratories in this report are deidentified and the report summarizes participant results from the intercomparison. The exercise occurred during the week of May 21, 2018.

42 ENGINEERING↗
DOE OSTI2018

Update of the nuclear criticality slide rule calculations: studies with common shielding materials - 25467

This paper presents preliminary results from the third phase of the current update to the nuclear criticality slide rule, in which MCNP, MAVRIC/Monaco, and COG have simulated the prompt neutron and photon dose from critical spheres of 4.95% enriched uranyl fluoride solution and 93.2% enriched uranium metal. New to this phase is the inclusion of various thicknesses of lead, steel, concrete, and water shielding. This phase also evaluated the effects of humidity on the unshielded configurations in the first phase, as well as the effects of changing the ground composition used in the first phase from concrete to dry soil. The small sample of results presented show that MCNP, MAVRIC/Monaco, and COG results are statistically the same or different by only a few percent. The impact of the shielding materials depends on their thickness, but doses decreased by nearly a factor of 100 are presented. In a few instances, buildup of gamma doses occurs due to neutron interactions in shielding materials. (authors)

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2017

Introduction of plutonium systems to the nuclear criticality slide rule

AWE (UK), IRSN (France), LLNL (USA) and ORNL (USA) began a long term collaboration effort in 2015 to update the nuclear criticality Slide Rule for the emergency response to a nuclear criticality accident. This document, published almost 20 years ago, gives order of magnitude estimates of key parameters, such as number of fissions and doses (neutron/gamma), useful for emergency response teams and public authorities. This paper presents, firstly, the motivation and the long term objectives for this update, then it introduces the initial critical configuration, and finally it presents the preliminary results obtained with modern 3D radiation transport codes and nuclear data for new configurations including plutonium systems. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2017

Dosimetry characterization of the Godiva Reactor under burst conditions

A series of sixteen (16) burst irradiations were performed in May 2014, fifteen of which were part of an international collaboration to characterize the Godiva IV fast burst reactor at the National Criticality Experiments Research Center (NCERC). Godiva IV is a bare cylindrical assembly of approximately 65 kg of highly enriched uranium fuel (93.2% 235 U metal alloyed with 1.5% molybdenum for strength) and is designed to perform controlled prompt critical excursions (Myers 2010, Goda 2013). Twelve of the irradiations were dedicated to neutron spectral measurements using a Bonner multiple sphere spectrometer. Three irradiations, with core temperature increases of 71.1°C, 136.9°C, and 229.9°C, were performed for generating comparative fluence data, establishing corrections for varying heights, testing linearity with burst temperature, and establishing gamma dose characteristics.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2015

A New Cryogenic Control System for the Vertical Test Area at Jefferson Lab

The Vertical Test Area at Jefferson Lab, consisting of eight vertical dewars, recently received a major upgrade by replacing the original (1995) cryogenic control system. A new, state-of-the-art, distributed control system (DC S) based on Programmable Logic Controllers (PLCs) was installed and commissioned. The new system increases facility throughput, reliability and cryogenic efficiency, while improving safety. The system employs a touchscreen graphical user interface and a highly redundant architecture on an Ethernet backbone.

Davis, K.↗
DOE OSTI2015

2014 CALIBAN and PROSPERO experiments for the criticality accident dosimetry intercomparison - 14529

Nuclear criticality accident dosimetry is very specific, due to the mixed fields and to energy and dose ranges which could be out of the range of classical individual dosimetry. The maximal neutron and gamma dose must be determined as well as other information such as the orientation of the victim in the radiation field. It is exceptionally challenging to establish doses in the event of partial body exposures. Therefore, frequent exercises are organized to maintain competencies and to train staff to perform such dosimetry. Experiments using the CALIBAN and PROSPERO reactors were performed in June and September 2014 in order to test various criticality accident dosimeters (CAD). These two metallic reactors are located at the CEA research center at Valduc (Cote-d'Or, France). They are composed of a metallic alloy of uranium with a high enrichment in the isotope {sup 235}U. These reactors are used for the production of mixed radiation fields primarily comprised of fission neutrons and gammas. CADs from three different laboratories (AWE, UK; IRSN, FR; LLNL, USA) were irradiated on water phantoms with three different orientations (0 deg. and 45 deg., front and rear faces) and free in air at both CALIBAN and PROSPERO reactors, in pulse and steady state modes. This paper will present the comparison of some results. These experiments will be useful preparation for other exercises planned in 2016 at the GODIVA-IV and FLATTOP reactors located at the Nevada National Security Site, USA. (authors)

42 ENGINEERING↗
DOE OSTI2015

Using ancient protein kinases to unravel a modern cancer drug’s mechanism

Evolution of dynamics affects function The drug Gleevac inhibits Abl kinases and is used to treat multiple cancers. The closely related Src kinases also play a role in cancer but are not inhibited effectively by Gleevac. Nevertheless, Gleevac-bound structures of Src and Abl are nearly identical. Based on this structural information and protein sequence data, Wilson et al. reconstructed the common ancestor of Src and Abl. Mutations that affected conformational dynamics caused Gleevac affinity to be gained on the evolutionary trajectory toward Abl and lost on the trajectory toward Src. Science , this issue p. 882

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS2014

Astrophysical Observations with the HEROES Balloon-borne Payload

The High Energy Replicated Optics to Explore the Sun (HEROES) payload flew on a balloon from Ft. Sumner, NM, September 21-22, 2013. HEROES is sensitive from about 20-75 keV and comprises 8 optics modules, each consisting of 13-14 nickel replicated optics shells and 8 Xenon-filled positionsensitive proportional counter detectors. HEROES is unique in that it is the first hard X-ray telescope that will observe the Sun and astrophysical targets in the same balloon flight. Our astrophysics targets include the Crab nebula and pulsar and the black hole binary GRS 1915+105. In this presentation, I will describe the HEROES mission, the data analysis pipeline and calibrations, and preliminary astrophysics results.

Wilson, C.↗