Planetary In Situ Capillary Electrophoresis System for End-to-End Analysis on Life Detection Missions
No abstract provided
Willis, Peter↗
Engineering topics
Willis, Peter
Publications and source records attributed to Willis, Peter.
Two-Dimensional Planetary Surface Landers
We proposed to develop a new landing approach that significantly reduces development time and obviates the most complicated, most expensive, and highest-risk phase of a landing mission. The concept is a blanket- or carpet-like two-dimensional (2D) lander (~1-m × 1-m surface area and <1-cm thick) with a low mass/drag ratio, which allows the lander to efficiently shed its approach velocity and provide a more robust structure for landing integrity. The form factor of these landers allows dozens to be stacked on a single spacecraft for transport and distributed en masse to the surface. Lander surfaces will be populated on both sides by surface-mount, low-profile sensors and instruments, surface-mount telecom, solar cells, batteries, processors, and memory. Landers will also incorporate thin flexible electronics, made possible in part by printable electronics technology. The mass and size of these highly capable technologies further reduces the required stiffness and mass of the lander structures to the point that compliant, lightweight, robust landers capable of passive landings are possible. This capability avoids the costly, complex use of rockets, radar, and associated structure and control systems. This approach is expected to provide an unprecedented science payload mass to spacecraft mass ratio of approximately 80% (estimated based on current knowledge). This compared to ~1% for Pathfinder, ~17% for MER, and 22% for MSL rovers. Clearly, one difference is rovers vs. a lower capability lander. An outcome of the Phase I study is a clear roadmap for near-term demonstration and long-term technology development.
Landers↗
Microfluidic Pumps Containing Teflon [Trademark] AF Diaphragms
Microfluidic pumps and valves based on pneumatically actuated diaphragms made of Teflon AF polymers are being developed for incorporation into laboratory-on-a-chip devices that must perform well over temperature ranges wider than those of prior diaphragm-based microfluidic pumps and valves. Other potential applications include implanted biomedical microfluidic devices, wherein the biocompatability of Teflon AF polymers would be highly advantageous. These pumps and valves have been demonstrated to function stably after cycling through temperatures from -125 to 120 C. These pumps and valves are intended to be successors to similar prior pumps and valves containing diaphragms made of polydimethylsiloxane (PDMS) [commonly known as silicone rubber]. The PDMS-containing valves ae designed to function stably only within the temperature range from 5 to 80 C. Undesirably, PDMS membranes are somwehat porous and retain water. PDMS is especially unsuitable for use at temperatures below 0 C because the formation of ice crystals increases porosity and introduces microshear.
Willis, Peter↗
Subcritical-Water Extraction of Organics from Solid Matrices
An apparatus for extracting organic compounds from soils, sands, and other solid matrix materials utilizes water at subcritical temperature and pressure as a solvent. The apparatus, called subcritical water extractor (SCWE), is a prototype of subsystems of future instrumentation systems to be used in searching for organic compounds as signs of past or present life on Mars. An aqueous solution generated by an apparatus like this one can be analyzed by any of a variety of established chromatographic or spectroscopic means to detect the dissolved organic compound( s). The apparatus can be used on Earth: indeed, in proof-of-concept experiments, SCWE was used to extract amino acids from soils of the Atacama Desert (Chile), which was chosen because the dryness and other relevant soil conditions there approximate those on Mars. The design of the apparatus is based partly on the fact that the relative permittivity (also known as the dielectric constant) of liquid water varies with temperature and pressure. At a temperature of 30 C and a pressure of 0.1 MPa, the relative permittivity of water is 79.6, due to the strong dipole-dipole electrostatic interactions between individual molecular dipoles. As the temperature increases, increasing thermal energy causes increasing disorientation of molecular dipoles, with a consequent decrease in relative permittivity. For example, water at a temperature of 325 C and pressure of 20 MPa has a relative permittivity of 17.5, which is similar to the relative permittivities of such nonpolar organic solvents as 1-butanol (17.8). In the operation of this apparatus, the temperature and pressure of water are adjusted so that the water can be used in place of commonly used organic solvents to extract compounds that have dissimilar physical and chemical properties.
Amashukeli, Xenia↗
Embossed Teflon AF Laminate Membrane Microfluidic Diaphragm Valves
A microfluidic system has been designed to survive spaceflight and to function autonomously on the Martian surface. It manipulates microscopic quantities of liquid water and performs chemical analyses on these samples to assay for the presence of molecules associated with past or present living processes. This technology lies at the core of the Urey Instrument, which is scheduled for inclusion on the Pasteur Payload of the ESA ExoMars rover mission in 2013. Fabrication processes have been developed to make the microfabricated Teflon-AF microfluidic diaphragm pumps capable of surviving extreme temperature excursions before and after exposure to liquid water. Two glass wafers are etched with features and a continuous Teflon membrane is sandwiched between them (see figure). Single valves are constructed using this geometry. The microfabricated devices are then post processed by heating the assembled device while applying pneumatic pressure to force the Teflon diaphragm against the valve seat while it is softened. After cooling the device, the embossed membrane retains this new shape. This solves previous problems with bubble introduction into the fluid flow where deformations of the membrane at the valve seat occurred during device bonding at elevated temperatures (100-150 C). The use of laminated membranes containing commercial Teflon AF 2400 sheet sandwiched between spun Teflon AF 1600 layers performed best, and were less gas permeable than Teflon AF 1600 membranes on their own. Spinning Teflon AF 1600 solution (6 percent in FLOURINERT(Registered TradeMark) FC40 solvent, 3M Company) at 500 rpm for 1.5 seconds, followed by 1,000 rpm for 3 seconds onto Borofloat glass wafers, results in a 10-micron-thick film of extremely smooth Teflon AF. This spinning process is repeated several times on flat, blank, glass wafers in order to gradually build a thick, smooth membrane. After running this process at least five times, the wafer and Teflon coating are heated under vacuum at 220 C for one hour in order to drive off any residual solvent present in the composite film. After this, a second blank, glass wafer is brought down from above and the stack is held under vacuum at 3 atm mechanical pressure for ten 10 hours.
Willis, Peter↗
Functionalized Carbon Nanotubes
Carbon nanotubes have created a great deal of excitement in the Materials Science community because of their outstanding mechanical, electrical, and thermal properties. Use of carbon nanotubes as reinforcements for polymers could lead to a new class of composite materials with properties, durability, and performance far exceeding that of conventional fiber reinforced composites. Organized arrays of carbon nanotubes, e.g., nanotube monolayers, could find applications as thermal management materials, light emitting devices, and sensor arrays. Carbon nanotubes could also be used as templates upon which nanotubes from other materials could be constructed. Successful use of carbon nanotubes in any of these potential applications requires the ability to control the interactions of nanotubes with each other and with other materials, e.g., a polymer matrix. One approach to achieving this control is to attach certain chemical groups to the ends and/or side-walls of the nanotubes. The nature of these chemical groups can be varied to achieve the desired result, such as better adhesion between the nanotubes and a polymer. Under a joint program between NASA Glenn, Clark Atlanta University, and Rice University researchers are working on developing a chemistry "tool-kit" that will enable the functionalization of carbon nanotubes with a variety of chemical groups. Recent results of this effort will be discussed.
Lebron, Marisabel↗