Engineering topics

Williams, Robert

Publications and source records attributed to Williams, Robert.

27 records · Page 2

NASA NTRS2001

Analysis of X-33 Linear Aerospike Plume Induced Base-Heating Environment During Power-Pack Out

The objectives of this viewgraph presentation are to predict the following: (1) dual-engine base-heating at 57% PL at sea level, and (2) dual-engine base-heating during PPO at three ascent abort trajectories. A systematically anchored computational fluid dynamics and heat transfer three-dimensional transfer simulation is being used to study the effect of reduced power levels on base-heating environments during sea level testing and during PPO. Preliminary results show the following: (1) convective heating is higher for the 57% PL than for 100% PL on most of the pillows and flex seals during sea level testing; and (2) convective heating on pillows and flex seals on the 'off' engine side is higher than that on the 'on' engine side.

Wang, Ten-See↗

NASA NTRS2000

Towards Flange-to-Flange Turbopump Simulations for Liquid Rocket Engines

The primary objective of this research is to support the design of liquid rocket systems for the Advanced Space Transportation System. Since the space launch systems in the near future are likely to rely on liquid rocket engines, increasing the efficiency and reliability of the engine components is an important task. One of the major problems in the liquid rocket engine is to understand fluid dynamics of fuel and oxidizer flows from the fuel tank to plume. Understanding the flow through the entire turbopump geometry through numerical simulation will be of significant value toward design. This will help to improve safety of future space missions. One of the milestones of this effort is to develop, apply and demonstrate the capability and accuracy of 3D CFD methods as efficient design analysis tools on high performance computer platforms. The development of the MPI and MLP versions of the INS3D code is currently underway. The serial version of INS3D code is a multidimensional incompressible Navier-Stokes solver based on overset grid technology. INS3D-MPI is based on the explicit massage-passing interface across processors and is primarily suited for distributed memory systems. INS3D-MLP is based on multi-level parallel method and is suitable for distributed-shared memory systems. For the entire turbopump simulations, moving boundary capability and an efficient time-accurate integration methods are build in the flow solver. To handle the geometric complexity and moving boundary problems, overset grid scheme is incorporated with the solver that new connectivity data will be obtained at each time step. The Chimera overlapped grid scheme allows subdomains move relative to each other, and provides a great flexibility when the boundary movement creates large displacements. The performance of the two time integration schemes for time-accurate computations is investigated. For an unsteady flow which requires small physical time step, the pressure projection method was found to be computationally efficient since it does not require any subiterations procedure. It was observed that the artificial compressibility method requires a fast convergence scheme at each physical time step in order to satisfy incompressibility condition. This was obtained by using a GMRES-ILU(0) solver in our computations. When a line-relaxation scheme was used, the time accuracy was degraded and time-accurate computations became very expensive. The current geometry for the LOX boost turbopump has various rotating and stationary components, such as inducer, stators, kicker, hydrolic turbine, where the flow is extremely unsteady. Figure 1 shows the geometry and computed surface pressure of the inducer. The inducer and the hydrolic turbine rotate in different rotational speed.

Kiris, Cetin↗

NASA NTRS1999

Unshrouded Centrifugal Turbopump Impeller

The ratio of rocket engine thrust to weight is a limiting constraint in placing more payload into orbit at a low cost. A key component of an engine's overall weight is the turbopump weight, Reducing the turbopump weight can result in significant engine weight reduction and hence, increased delivered payload. There are two main types of pumps: centrifugal and axial pumps. These types of pumps can be further sub-divided into those with shrouds and those without shrouds (unshrouded pumps). Centrifugal pumps can achieve the same pump discharge pressure as an axial pump and it requires fewer pump stages and lower pump weight than an axial pump. Also, with unshrouded centrifugal pumps (impeller), the number of stages and weight can be further reduced. However. there are several issues with regard to using an unshrouded impeller: 1) there is a pump performance penalty due to the front open face recirculation flow; 2) there is a potential pump axial thrust problem from the unbalanced front open face and the back shroud face; and, 3) since test data is very linu'ted for this configuration, there is uncertainty in the magnitude and phase of the rotordynamics forces due to the front impeller passage. The purpose of the paper is to discuss the design of an unshrouded impeller and to examine the design's hydrodynamic performance, axial thrust, and rotordynamics performance. The design methodology will also be discussed. This work will help provide some guidelines for unshrouded impeller design. In particular, the paper will discuss the design of three unshrouded impellers - one with 5 full and 5 partial blades (5+5). one with 6+6 blades and one with 8+8 blades. One of these designs will be selected for actual fabrication and flow test. Computational fluid dynamics (CFD) is used to help design and optimize the unshrouded impeller. The relative pump performance penalty is assessed by comparing the CFD results of the unshrouded impeller with the equivalent shrouded impeller for a particular design. Limited unshrouded - versus - shrouded impeller data from the J-2 pump is used to anchor the CFD. Since no detailed impeller blade force data is available, axial thrust and rotordynamic force predictions are based on the CFD model. For the axial thrust, the impeller front flow passage axial force is integrated from the CFD results and compared to the equivalent shrouded impeller axial force. For the rotordynamics forces, the fluid reaction forces are computed from unsteady flow CFD results using a moving boundary method; the rotor- shaft is moved at several whirl-to-speed frequency ratios to extract the rotordynamics coefficients.

Prueger, George↗

NASA NTRS1998

Hydrodynamic Design of the Fastrac Turbopump

A 60,000 lb trust liquid Oxygen (LOX) and rocket propellant #1 (RP-1) rocket engine is being developed at the Marshall Space Flight Center (MSFC) as part of NASA's ongoing effort to lower the cost of access to space. The goal of the program is to demonstrate a low cost rocket engine with acceptable performance. In order to reduce design and development risk, computational fluid dynamics (CFD) analysis was used extensively in the design process, especially in the design of the turbopump. This paper documents the process used and significant results obtained during the design of the LOX and RP-1 pumps. This includes the design of the inlet manifolds, the integral inducer-impellers, the diffusers, and the collector volutes. The resulting designs incorporate low-cost design features while meeting the engine cycle requirements.

Garcia, Roberto↗

NASA NTRS1996

Surface and Volume Grid Generation in Parametric Form

The algorithm for surface modeling and volume grid generation using parametric Non-Uniform Rational B-splines (NURBS) geometric representation are presented. The enhanced re-parameterization algorithm which can yield a desired physical distribution on the curve, surface, and volume is also presented. This approach bridges the gap between computer aided design surface/volume definition and surface/volume grid generation.

Yu, Tzuyi↗

NASA NTRS1995

New observations with the HST Goddard High Resolution Spectrograph of the low-redshift Lyman-Alpha clouds in the 3C 273 line of sight

We presenty spectra of 3C 273 between 1216 and 1250 A obtained in the (pre-COSTAR (Corrective Optics Space Telescope Axial Replacement instrument)) configuration of the Goddard High Resolution Spectrograph (GHRS) taken with the G160M grating with a resolution approximately = 20 km/s. The two strong Ly alpha lines at velocities of approximately 1000 and approximately 1600 km/s are well fitted with Voigt profiles and yield column densities, Doppler parameters and redshifts of log N(H I)=14.19 +/- 0.04 V(sub Dop)=40.7 +/- 3.0 km/s, V = 1012.4 +/- 2.0 km/s, and log N(H I)=14.22 +/- 0.07, V(sub Dop)=34.2 +/- 3.3 km/s and V = 1582.0 +/- 2.0 km/s, respectively. Motivated by the initial announcement by Williams and Schommer of detectable H alpha emission associated with the approximately 1600 km/s cloud, we discuss the difficulty of finding models which can account for emission of that magnitude given the observed neutral hydrogen column density, though a recent reobservation by these authors has shown the initial detection to be spurious. The C/H abundance ratio is probably less than about one-fourth of the solar abundance in these clouds, although this result is very uncertain and model dependent.

Weymann, Ray↗

NASA NTRS1994

The Analysis of Emission Lines; A Meeting in Honour of the 70th Birthdays of D. E. Osterbrock and M. J. Seaton

A review of the field of astronomical spectroscopy with emphasis on emission lines in astrophysical plasmas is presented. A brief history of UV spectroscopy instruments is given, following by a discussion and tabulation of major atlases of UV emission-line objects to date (mid-1994). A discussion of the major diagnostic UV emission lines in the approx. 912-3200 A spectral region that are useful for determining electron densities, temperatures, abundances, and extinction in low- to moderate density plasmas is given, with examples of applications to selected objects. The review concludes by presenting some recent results from HST, HUT, and IUE on UV emission-line spectroscopy of nebulae and active galaxies.

Williams, Robert↗

NASA NTRS1992

CFD analysis to optimize a design modification of BSMT

The Bearings, Seals and Materials Tester (BSMT) is a test article being used at MSFC to evaluate the performance of conventional rolling contact bearings. Pressure differentials between the BSMT inlet and exit cavities are found to cause large parasitic axial loads on the bearing-carrier walls. These parasitic loads, besides being detrimental to the life of bearings, make the testing and evaluation of bearing performance very difficult, and need to be eliminated if at all possible. The objectives of this study are to estimate the hydrodynamic loads on the bearings and to recommend feasible design modifications for BSMT to eliminate the parasitic loads. Three-dimensional computational analyses of inlet and exit cavities in their baseline configuration were performed with REFLEQS which is an advanced finite-volume Navier-Stokes code. Computations were performed with and without a 1/4 inch diameter temperature probe included in each of the cavities. The results of the analyses indicate that the temperature probes substantially alter the flow field and reduce the pressure drop/rise in the cavities. The overall pressure drop across the tester compares quite well with the measurements.

Ratcliff, Mark↗

NASA NTRS1988

Using hypermedia to develop an intelligent tutorial/diagnostic system for the Space Shuttle Main Engine Controller Lab

This is a tutorial/diagnostic system for training personnel in the use of the Space Shuttle Main Engine Controller (SSMEC) Simulation Lab. It also provides a diagnostic capable of isolating lab failures at least to the major lab component. The system was implemented using Hypercard, which is an program of hypermedia running on Apple Macintosh computers. Hypercard proved to be a viable platform for the development and use of sophisticated tutorial systems and moderately capable diagnostic systems. This tutorial/diagnostic system uses the basic Hypercard tools to provide the tutorial. The diagnostic part of the system uses a simple interpreter written in the Hypercard language (Hypertalk) to implement the backward chaining rule based logic commonly found in diagnostic systems using Prolog. Some of the advantages of Hypercard in developing this type of system include sophisticated graphics, animation, sound and voice capabilities, its ability as a hypermedia tool, and its ability to include digitized pictures. The major disadvantage is the slow execution time for evaluation of rules (due to the interpretive processing of the language). Other disadvantages include the limitation on the size of the cards, that color is not supported, that it does not support grey scale graphics, and its lack of selectable fonts for text fields.

Oreilly, Daniel↗