Engineering topics
Publications and source records attributed to Williams, R..
A new test technology is described which was developed for space system integration. The ultimate purpose of the system is to support the automatic generation of test systems in real time, distributed computing environments. The Intelligent Test Integration System (ITIS) is a knowledge based layer above the traditional test system components which can generate complex test configurations from the specification of test scenarios.
A programming model and architecture which was developed for the design and implementation of complex, heterogeneous measurement and control systems is described. The Multigraph Architecture integrates artificial intelligence techniques with conventional software technologies, offers a unified framework for distributed and shared memory based parallel computational models and supports multiple programming paradigms. The system can be implemented on different hardware architectures and can be adapted to strongly different applications.
Combination of ceramic and plastic withstands many depressurizations. Stack of washers surrounds leadthrough electrode. Under pressure washers expand to fill leadthrough hole in high-pressure vessel. Seal thus formed withstands 20 or more pressurization/depressurization cycles. Seal composed of neoprene, polytetrafluoroethylene, nylon and high-purity, high-density commercial alumina ceramic.
Changes of the geometry of the open field line region (namely, the polar cap) caused by the passage of a tangential IMF discontinuity are simulated using the model constructed by Akasofu and Roederer (1983). A singly-bounded open field line region tends to split into two, forming a narrow closed field line region and thus allowing the formations of a plasma sheet and of an auroral arc across the highest latitude region of the earth. The three-dimensional geometry of some of the closed field lines in the narrow closed region is examined. In this connection, an interesting observation of the formation of an auroral arc over Thule, Greenland, is reported.
The computer program known as PLOTRW was custom made to satisfy some of the graphics requirements for the data collected in the Space Plasma Laboratory at the Johnson Space Center (JSC). The general requirements for the program were as follows: (1) all subroutines shall be callable through a FORTRAN source program; (2) all graphs shall fill one page and be properly labeled; (3) there shall be options for linear axes and logarithmic axes; (4) each axis shall have tick marks equally spaced with numeric values printed at the beginning tick mark and at the last tick mark; and (5) there shall be three options for plotting. These are: (1) point plot, (2) line plot and (3) point-line plot. The subroutines were written in FORTRAN IV for the LSI-11 Digital equipment Corporation (DEC) Computer. The program is now operational and can be run on any TEKTRONICX graphics terminal that uses a DEC Real-Time-11 (RT-11) operating system.
The physical properties of quasi-one-dimensional conductors are profoundly influenced by slight changes in structure. The unusual structural features of this class of materials include only short range order of the anions and structure modulation. The nature of disorder and structure modulation can affect the character of the metal-to-insulator transition at low temperature, and may allow us to make some predictions of low temperature behavior based on room temperature structural properties.
Primary lithium cells which use LiAlCl4/SOCl2 electrolyte exhibit high energy density and long life. Currently these cells pose a safety problem since they have been found to vent or explode. This paper summarizes experiments to resolve the safety problem of Li-SOCl2 cells by thermal modeling and identification of possibly hazardous intermediates formed during discharge of these cells. A thermal model and mechanism for the reduction of SOCl2 are presented, as well as a discussion of their application to Li-SOCl2 cell safety.
Design parameters for two large area, low cost solar cells are presented, and electron irradiation testing, thermal alpha testing, and cell processing are discussed. The devices are a 2 ohm-cm base resistivity silicon cell with an evaporated aluminum reflector produced in a dielectric wraparound cell, and a 10 ohm-cm silicon cell with the BSF/BSR combination and a conventional contact system. Both cells are 5.9 x 5.9 cm and require 200 micron thick silicon material due to mission weight constraints. Normalized values for open circuit voltage, short circuit current, and maximum power calculations derived from electron radiation testing are given. In addition, thermal alpha testing values of absorptivity and emittance are included. A pilot cell processing run produced cells averaging 14.4% efficiencies at AMO 28 C. Manufacturing for such cells will be on a mechanized process line, and the area of coverslide application technology must be considered in order to achieve cost effective production.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
X-ray powder diffraction studies of two semiconducting crystal phases in the organic charge transfer salt (DEPE)(TCNQ) sub 4 has revealed almost identical electrical properties to those of metallic crystals. It is hypothesized that the similarity arises from the nature of the measurements themselves, i.e., electrode geometry. The possibility that a separate metallic phase for (DEPE)(TCNQ) sub 4 exists, is not, however, ruled out.
The attitude support activities of the Radio Astronomy Explorer-B are reported. The performance of the spacecraft hardware and software are discussed along with details of the mission events, from launch through main boom deployment. Reproductions of displays are presented which were used during support activities. The interactive graphics proved the support function by providing the quality control necessary to ensure mission success in an environment where flight simulated ground testing of spacecraft hardware cannot be performed.
The characteristics of Efratom optically pumped rubidium frequency standards are discussed. The Efratom units were compared with cesium beam and hydrogen maser standards and showed a stability of approximately 5 times 10 to the minus 12th power over two one-week periods. Dependency of frequency upon the environmental parameters of pressure, magnetic field, temperature, supply voltage, and acceleration was measured. A package of three units with automatic phase comparison and recording was designed and constructed to allow a measurement of relativistic effects on time with high accuracy during space missions.
Mineralogy and petrology of Apollo 12 igneous rocks 12004, 12008, 12009 and 12022, noting ilmenite, olivine and spinel content and metal grains composition
Design considerations of central programmer, common address, and data return bus
Compatible double sideband/single sideband/constant bandwidth FM telemetry system for wideband data