Engineering Papers⌕ Search

Engineering topics

Williams, J. L.

Publications and source records attributed to Williams, J. L..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Maximum likelihood estimation for distributed parameter models of flexible spacecraft

A distributed-parameter model of the NASA Solar Array Flight Experiment spacecraft structure is constructed on the basis of measurement data and analyzed to generate a priori estimates of modal frequencies and mode shapes. A Newton-Raphson maximum-likelihood algorithm is applied to determine the unknown parameters, using a truncated model for the estimation and the full model for the computation of the higher modes. Numerical results are presented in a series of graphs and briefly discussed, and the significant improvement in computation speed obtained by parallel implementation of the method on a supercomputer is noted.

Taylor, L. W., Jr.↗
NASA NTRS1987

Distributed parameter modeling of the structural dynamics of the Solar Array Flight Experiment

A distributed-parameter model of the structural dynamics of the space-shuttle-deployed Solar Array Flight Experiment is developed and used to produce estimates of the modal frequencies and mode shapes. A lumped parameter version of the distributed model is used to estimate model characteristics by analyzing the measured responses of 32 targets. To make the modeling more tenable, a distributed parameter system is used to reduce the number of unknown parameters, a modified Newton-Raphson technique is used for rapid convergence, and a parallel processing supercomputer is used for more efficient computation. The performances of computers with a high-speed serial processor and with a high-speed parallel processor are compared. The best results are obtained with the modeling approach in which maximum likelihood estimation is applied to distributed parameter models.

Taylor, L. W., Jr.↗
NASA NTRS1985

Challenges in the development of the orbiter radiator system

Major technical challenges which were met in the design and development of the Space Shuttle Orbiter Radiator System are discussed. This system rejects up to 30 kW of waste heat from eight individual radiators having a combined surface area of 175 sq m. The radiators, which are deployable, are mounted on the inside of the payload bay doors for protection from aerodynamic heating during ascent and re-entry. While in orbit the payload bay doors are opened to expose the radiators for operation. An R21 coolant loop accumulates waste heat from various components in the Orbiter and delivers the heat to the radiators for rejection to space. Specific challenges included high acoustically induced loads during lift-off, severe radiating area constraints, demanding heat load control requirements, and long life goals. Details of major design and analysis efforts are discussed. The success of the developed hardware in satisfying mission objectives showed how well the design challenge was met.

Williams, J. L.↗
NASA NTRS1975

Bubble-domain circuit wafer evaluation coil set

Coil structures have been designed to permit nondestructive testing of bubble wafers. Wafers can be electrically or optically inspected and operated from quasi-static frequency to maximum device operating frequency.

Chen, T. T.↗
NASA NTRS1975

Self-contained heat rejection module for future spacecraft

This paper discusses development of a Self-Contained Heat Rejection Module (SHRM) which can be used on a wide variety of future spacecraft launched by the space shuttle orbiter. The SHRM contains radiators which are deployed by a scissor-mechanism and the flow equipment including pumps, accumulator, by-pass valves, and controllers necessary to reject heat from those radiators. Heat transfer between SHRM and the parent vehicle is effected by a contact heat exchanger. This device provides heat transfer between two separate flow loops through a mechanical connection. This approach reduces the time required to attach the SHRM to the payload, and increases the reliability of the SHRM flow loop since breaking into the fluid system in the field is not required. The SHRM concept also includes a refrigeration system to increase heat rejection capacity in adverse environments, or to provide for a lower return temperature, down to -23 C.

Fleming, M. L.↗
NASA NTRS1974

Extraction from flight data of lateral aerodynamic coefficients for F-8 aircraft with supercritical wing

A parameter-extraction algorithm was used to determine the lateral aerodynamic derivatives from flight data for the F-8 aircraft with supercritical wing. The flight data used were the recorded responses to aileron or rudder pulses for Mach numbers of 0.80, 0.90, and 0.98. Results of this study showed that a set of derivatives were determined which yielded a calculated aircraft response almost identical with the response measured in flight. Derivatives extracted from motion resulting from rudder inputs were somewhat different from those resulting from aileron inputs. It was found that the derivatives obtained from the rudder-input data were highly correlated in some instances. Those from the aileron input had very low correlations and appeared to be the more reliable.

Williams, J. L.↗
NASA NTRS1974

Space shuttle orbiter mechanical refrigeration system

A radiator/condenser was designed which is efficient in both condensation (refrigeration) and liquid phase (radiator) operating modes, including switchover from the refrigeration mode to the radiator mode and vice versa. A method for predicting the pressure drop of a condensing two-phase flow in zero-gravity was developed along with a method for predicting the flow regime which would prevail along the condensation path. The hybrid refrigeration system was assembled with the two radiator/condenser panels installed in a space environment simulator. The system was tested under both atmospheric and vacuum conditions. Results of the tests are presented.

Williams, J. L.↗
NASA NTRS1974

Extraction from flight data of longitudinal aerodynamic coefficients for F-8 aircraft with supercritical wing

The longitudinal aerodynamic derivatives of the F-8 aircraft with supercritical wing were obtained from flight data by a parameter-extraction algorithm at Mach numbers of 0.8, 0.9, and 0.98. A set of derivatives were obtained from which calculated aircraft responses were correlated almost identically with actual flight responses. In general, the trends of the extracted derivatives obtained by the algorithm agreed with those obtained by a Newton-Raphson method and with preliminary data from the Langley 8-foot transonic pressure tunnel. The wind-tunnel damping derivatives were, however, substantially higher than the converged damping derivatives possibly because of Reynolds number differences between flight and model tests.

Williams, J. L.↗
NASA NTRS1974

Lateral static and dynamic aerodynamic parameters of the Kestrel aircraft (XV-6A) extracted from flight data

Flight test data have been used to extract the lateral static and dynamic aerodynamic parameters of the Kestrel aircraft. The aircraft configurations included thrust-jet angles of 0 deg, 15 deg, and 30 deg, and the test Mach numbers were 0.43, 0.62, and 0.82. The results showed that most of the parameters varied linearly with trim normal-force coefficient. The directional stability parameter showed a small increase with increasing trim normal-force coefficient and also with nozzle deflection. The effective-dihedral parameter, the damping-in-roll parameter, and damping-in-yaw parameter all increased (became more negative) with increasing trim normal-force coefficient. For the latter three parameters, the effect of nozzle deflection was dependent on the trim normal-force coefficient.

Suit, W. T.↗
NASA NTRS1974

A photographic study of flow condensation in 1-g and zero-gravity environments

The test articles investigated include two full-scale radiator/condenser panels and a system of three parallel-connected fused quartz tubes. Testing was performed initially on the ground, with both horizontal and inclined flow passage orientations, and additionally in an aircraft flying 0-g trajectories. The photographic observations were made with two high speed cameras and a low speed camera. The flow regimes observed are compared with those predicted by the Baker chart (1954). The Baker chart is well in accord with physical reality in the annular flow region. However, a stratified-annular flow regime observed has no counterpart in the Baker categorization.

Keshock, E. G.↗
NASA NTRS1973

Longitudinal aerodynamic parameters of the Kestrel aircraft (XV-6A) extracted from flight data

Flight-test data have been used to extract the longitudinal aerodynamic parameters of a vectored-thrust aircraft. The results show that deflecting the thrust past 15 has an effect on the pitching-moment derivatives and tends to reduce the static stability. The trend toward reduction in the longitudinal stability also been noted by the pilots conducting the flight tests.

Suit, W. T.↗
NASA NTRS1972

Extraction of longitudinal aerodynamic coefficients from forward-flight conditions of a tilt-wing V/STOL airplane

A parameter-estimation algorithm was used to extract the longitudinal aerodynamic derivatives from flight data for the XC-142A airplane in a cruise condition. The flight data were the response to a tail-plane doublet input. Results of this study showed that a set of derivatives were determined which yielded a calculated aircraft response in close agreement with the measured response. This calculated response was in much closer agreement with the flight data than the response obtained by using derivatives which were calculated from empirical methods. There were large differences between some of the important derivatives extracted from flight data and those calculated from empirical methods. The reasons for these differences were not identified.

Williams, J. L.↗
NASA NTRS1972

Advanced Extravehicular Protective System (AEPS) study

A summary is presented of Advanced Extravehicular Protective Systems (AEPS) for the future missions beyond Skylab in earth orbit, on the lunar surface, and on the Martian surface. The study concentrated on the origination of regenerable life support concepts for use in portable extravehicular protective systems, and included evaluation and comparison with expendable systems, and selection of life support subsystems. The study was conducted in two phases. In the first phase, subsystem concepts for performing life support functions in AEPS which are regenerable or partially regenerable were originated, and in addition, expendable subsystems were considered. Parametric data for each subsystem concept were evolved including subsystem weight and volume, power requirement, thermal control requirement; base regeneration equipment weight and volume, requirement. The second phase involved an evaluation of the impact of safety considerations involving redundant and/or backup systems on the selection of the regenerable life support subsystems. In addition, the impact of the space shuttle program on regenerable life support subsystem development was investigated.

Williams, J. L.↗
NASA NTRS1972

Regenerable thermal control and carbon dioxide control techniques for use in advanced extravehicular protective systems

The most promising closed CO2 control concept identified by this study is the solid pellet, Mg(OH2)2 system. Two promising approaches to closed thermal control were identified. The AHS system uses modular fusible heat sinks, with a contingency evaporative mode, to allow maximum EVA mobility. The AHS/refrigerator top-off subsystem requires an umbilical to minimize expendables, but less EVA time is used to operate the system, since there is no requirement to change modules. Both of these subsystems are thought to be practical solutions to the problem of providing closed heat rejection for an EVA system.

Williams, J. L.↗
NASA NTRS1971

Evaluation and selection of refrigeration systems for lunar surface and space applications

Evaluated are the various refrigeration machines which could be used to provide heat rejection in environmental control systems for lunar surface and spacecraft applications, in order to select the best refrigeration machine for satisfying each individual application and the best refrigeration machine for satisfying all of the applications. The refrigeration machine considered include: (1) vapor comparison cycle (work-driven); (2) vapor adsorption cycle (heat-driven); (3) vapor absorption cycle (heat-driven); (4) thermoelectric (electrically-driven); (5) gas cycle (work driven); (6) steam-jet (heat-driven).

Copeland, R. J.↗
NASA NTRS1971

Advanced Extravehicular Protective Systems (AEPS) study

A description is given of life support subsystem concepts for advanced extravehicular protective systems (AEPS) intended for use on future orbital, lunar surface, and Mars surface missions in the late 1970's and 1980's. Primary interest was centered around the thermal control and carbon dioxide control subsystems because they offer the greatest potential for total weight savings. Emphasis was placed on the generation of regenerable subsystem concepts; however, partially regenerable and expendable concepts were also considered. Previously conceived and developed subsystem concepts were included in the study. Concepts were evaluated on the basis of subsystem weight and volume, and subsystem contribution to parent vehicle weight and volume, which included spares, regeneration equipment, expendables, expandables storage penalty, power penalty, and process heating or cooling penalty. Results are presented showing total weight and volume penalty as a function of total mission extravehicular activity (EVA) hours, and showing EVA weight and volume as a function of EVA duration. Subsystem concepts are recommended for each life support function, and secondary concepts which should be developed are also identified.

Williams, J. L.↗