Engineering topics

Wilkie, William K.

Publications and source records attributed to Wilkie, William K..

8 records

NASA NTRS2019

Advanced Composite Solar Sail System: Demonstrating Deployable Composite Solar Sails for Future Deep Space Small Spacecraft

NASA is developing new deployable structures and materials technologies for solar sail propulsion systems destined for future low-cost deep space missions. Solar sails eliminate the need for conventional rocket propellants, relying instead upon the pressure of sunlight to generate continuous thrust. They can operate indefinitely, limited only by the space environment durability of the solar sail materials and spacecraft electronic systems.At NASA's Langley Research Center in Hampton, Virginia, and NASA's Ames Research Center in California's Silicon Valley, researchers and engineers are planning a mission to demonstrate the next generation of solar sail technology for small interplanetary spacecraft. As part of this development effort, the Advanced Composite Solar Sail System (ACS3) will demonstrate deployment of an approximately 800 square foot (74 square meter) composite boom (mast) solar sail system in low-Earth orbit. This will be the first use of composite booms as well as sail packing and deployment systems for a solar sail in orbit.

composite materials↗

NASA NTRS2019

Advanced Composite Solar Sail System Animation

At NASA's Langley Research Center in Hampton, Virginia, and Ames Research Center in California's Silicon Valley, researchers and engineers are planning a mission to demonstrate the next generation of solar sail technology for small interplanetary spacecraft. As part of this development effort, the Advanced Composite Solar Sail System (ACS3) will demonstrate deployment of an approximately 800 square foot (74 square meter) composite boom solar sail system in low-Earth orbit. This will be the first use of composite booms as well as sail packing and deployment systems for a solar sail in orbit. Also developed for ACS3 is an innovative tape-spool boom extraction system to minimize blossoming, or jamming, of the coiled booms during deployment.

Horner, Scott D.↗

NASA NTRS2019

A Multi-Blade Model for Heliogyro Solar Sail Structural Dynamics Analysis

An analytical model is derived to study the structural dynamic stability behavior for the free-flying heliogyro solar sail consisting of a finite set of symmetric or evenly distributed thin blades on a flat surface. Key properties of the flutter instability are described in terms of the relationship among the eigenvalues and eigenvectors associated with a flutter instability frequency. Various simulation cases for an idealized single blade, fixed rotational speed heliogyro model, and a generalized multi-bladed, freely spinning heliogyro model are presented to show how the flutter instability frequencies change as a function of the solar radiation pressure and the size of the dynamic model. Convergence of the flutter instability frequency versus the system order is demonstrated.

Juang, Jer-Nan↗

NASA NTRS2017

Self-Latching Piezocomposite Actuator

A self-latching piezocomposite actuator includes a plurality of shape memory ceramic fibers. The actuator can be latched by applying an electrical field to the shape memory ceramic fibers. The actuator remains in a latched state/shape after the electrical field is no longer present. A reverse polarity electric field may be applied to reset the actuator to its unlatched state/shape. Applied electric fields may be utilized to provide a plurality of latch states between the latched and unlatched states of the actuator. The self-latching piezocomposite actuator can be used for active/adaptive airfoils having variable camber, trim tabs, active/deformable engine inlets, adaptive or adjustable vortex generators, active optical components such as mirrors that change shapes, and other morphing structures.

Wilkie, William K.↗

NASA NTRS2014

Recent Progress in Heliogyro Solar Sail Structural Dynamics

Results from recent National Aeronautics and Space Administration (NASA) research on the structural dynamics and control characteristics of heliogyro solar sails are summarized. Specific areas under investigation include coupled nonlinear finite element analysis of heliogyro membrane blade with solar radiation pressure effects, system identification of spinning membrane structures, solarelastic stability analysis of heliogyro solar sails, including stability during blade deployment, and results from small-scale in vacuo dynamics experiments with spinning high-aspect ratio membranes. A low-cost, rideshare payload heliogyro technology demonstration mission concept, used as a mission context for these heliogyro structural dynamics and solarelasticity investigations, is also described.

Wilkie, William K.↗

NASA NTRS2011

The Heliogyro Reloaded

The heliogyro is a high-performance, spinning solar sail architecture that uses long - order of kilometers - reflective membrane strips to produce thrust from solar radiation pressure. The heliogyro s membrane blades spin about a central hub and are stiffened by centrifugal forces only, making the design exceedingly light weight. Blades are also stowed and deployed from rolls; eliminating deployment and packaging problems associated with handling extremely large, and delicate, membrane sheets used with most traditional square-rigged or spinning disk solar sail designs. The heliogyro solar sail concept was first advanced in the 1960s by MacNeal. A 15 km diameter version was later extensively studied in the 1970s by JPL for an ambitious Comet Halley rendezvous mission, but ultimately not selected due to the need for a risk-reduction flight demonstration. Demonstrating system-level feasibility of a large, spinning heliogyro solar sail on the ground is impossible; however, recent advances in microsatellite bus technologies, coupled with the successful flight demonstration of reflectance control technologies on the JAXA IKAROS solar sail, now make an affordable, small-scale heliogyro technology flight demonstration potentially feasible. In this paper, we will present an overview of the history of the heliogyro solar sail concept, with particular attention paid to the MIT 200-meter-diameter heliogyro study of 1989, followed by a description of our updated, low-cost, heliogyro flight demonstration concept. Our preliminary heliogyro concept (HELIOS) should be capable of demonstrating an order-of-magnitude characteristic acceleration performance improvement over existing solar sail demonstrators (HELIOS target: 0.5 to 1.0 mm/s2 at 1.0 AU); placing the heliogyro technology in the range required to enable a variety of science and human exploration relevant support missions.

Wilkie, William K.↗

NASA NTRS2011

Correcting Thermal Deformations in an Active Composite Reflector

Large, high-precision composite reflectors for future space missions are costly to manufacture, and heavy. An active composite reflector capable of adjusting shape in situ to maintain required tolerances can be lighter and cheaper to manufacture. An active composite reflector testbed was developed that uses an array of piezoelectric composite actuators embedded in the back face sheet of a 0.8-m reflector panel. Each individually addressable actuator can be commanded from 500 to +1,500 V, and the flatness of the panel can be controlled to tolerances of 100 nm. Measuring the surface flatness at this resolution required the use of a speckle holography interferometer system in the Precision Environmental Test Enclosure (PETE) at JPL. The existing testbed combines the PETE for test environment stability, the speckle holography system for measuring out-of-plane deformations, the active panel including an array of individually addressable actuators, a FLIR thermal camera to measure thermal profiles across the reflector, and a heat source. Use of an array of flat piezoelectric actuators to correct thermal deformations is a promising new application for these actuators, as is the use of this actuator technology for surface flatness and wavefront control. An isogrid of these actuators is moving one step closer to a fully active face sheet, with the significant advantage of ease in manufacturing. No extensive rib structure or other actuation backing structure is required, as these actuators can be applied directly to an easy-to-manufacture flat surface. Any mission with a surface flatness requirement for a panel or reflector structure could adopt this actuator array concept to create lighter structures and enable improved performance on orbit. The thermal environment on orbit tends to include variations in temperature during shadowing or changes in angle. Because of this, a purely passive system is not an effective way to maintain flatness at the scale of microns over several meters. This technology is specifically referring to correcting thermal deformations of a large, flat structure to a specified tolerance. However, the underlying concept (an array of actuators on the back face of a panel for correcting the flatness of the front face) could be extended to many applications, including energy harvesting, changing the wavefront of an optical system, and correcting the flatness of an array of segmented deployable panels.

Bradford, Samuel C.↗

NASA NTRS2004

Recent Developments in NASA Piezocomposite Actuator Technology

In this paper, we present an overview of recent progress in the development of the NASA Macro-Fiber Composite (MFC) piezocomposite actuator device. This will include a brief history of the development of the MFC, a description of the standard manufacturing process used to fabricate MFC actuators, and a summary of ongoing MFC electromechanical characterization testing. In addition, we describe the development of a prototype single-crystal piezoelectric MFC device, and compare its performance with MFC actuator specimens utilizing conventional piezoceramic materials.

Wilkie, William K.↗