Engineering Papers⌕ Search

Engineering topics

Wilhite, A. W.

Publications and source records attributed to Wilhite, A. W..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Thrust vectoring for single-stage-to-orbit, horizontal takeoff, horizontal landing, space vehicles

The preliminary design of a horizontal takeoff, horizontal landing, single-stage-to-orbit, rocket-powered space vehicle was performed. The purpose was to examine technology requirements for future small payload launch vehicles. The distinguishing aspect of the design was the utilization of thrust vectoring to provide half of the lift at takeoff. The inclusion of a canard was necessary to provide additional lift at takeoff and to balance the moments produced with thrust vectoring. A weights estimation, an aerodynamic assessment, a trajectory analysis, and a gear weight analysis were performed. The takeoff weight of the resulting vehicle was approximately 1.26 million pounds, based on advanced technology structures and subsystems. The vehicle was designed to deliver a 5000-pound payload to a polar orbit.

Cunningham, M. J.↗
NASA NTRS1986

Analysis of separation of a two-stage winged launch vehicle

The feasibility of separating a two-stage winged, parallel configured launch vehicle at Mach 3 has been determined. The two-stage fully-reusable launch vehicle is comprised of an orbiter, which can be used alone as a single-stage-to-orbit vehicle, and a booster which is identical to the baseline orbiter design. A three-degree-of-freedom analysis was conducted on the ascent trajectory of the two-stage concept to determine the optimum staging conditions. The booster provides all propellant for both stages using a crossfeed system until staging occurs. After staging, the empty booster glides back to the launch site for a horizontal landing. To analyze the separation maneuver, the six-degree-of-freedom equations of motion for both stages were numerically integrated using a computer program which incorporates analytically derived interference aerodynamic data. The necessary conditions for a successful separation were determined and required the use of active controls on both the orbiter and booster. Once the booster and orbiter were separated, a three-degree-of-freedom analysis was conducted on the booster's glideback trajectory.

Naftel, J. C.↗
NASA NTRS1984

Second-generation Space Shuttle

This is a review of an in-house study at the Langley Research Center to identify the technology requirements that are necessary to develop a second-generation Space Shuttle in the post 2000 time period. The study, Future Space Transportation System Study, had two main objectives: (1) to define the launch-vehicle concepts which best meet the needs and opportunities for improved space transportation economics and capabilities for a Space Shuttle replacement and (2) to extend the level of technology assessments with respect to previous advanced system studies, especially in the areas of stuctures, propellant tankage, thermal protection systems, aerodynamics, and operations.

Arrington, J. P.↗
NASA NTRS1984

Performance assessment of aero-assisted orbital transfer vehicles

Aero-assisted orbital transfer vehicles are analyzed. The aerodynamic characteristics over the flight profile and three- and six-degree-of-freedom performance analyses were determined. The important results, to date, are: (1) the aerodynamic preliminary analysis system, an interactive computer program, used to predict the aerodynamics (performance, stability, and control) for these vehicles; (2) the performance capability, e.g., maximum inclination change, maximum heating rate, and maximum sensed acceleration, can be determined using continuum aerodynamics only; (3) guidance schemes can be developed that allow for errors in atmospheric density prediction, mispredicted trim angle of attack, and off-nominal atmospheric interface conditions, even for vehicles with a low lift-to-drag ratio; and (4) multiple pass trajectories can be used to reduce the maximum heating rate.

Powell, R. W.↗
NASA NTRS1984

Performance aerodynamics of aeroassisted orbital transfer vehicles

A method for predicting the performance aerodynamics of aeroassisted orbital transfer vehicles was developed based on techniques that were used in the aerodynamic databook of the Space Shuttle orbiter and theories from the Hypersonic Arbitrary Body Program. The method spans the entire flight profile of the aeroassisted orbital transfer vehicles from the extreme high altitude non-continuum regime to the highly viscous continuum regime. Results from this method are compared with flight data from the Shuttle orbiter, Apollo Capsule, and the Viking Aeroshell. Finally, performance aerodynamics are estimated for three aeroassisted orbital transfer vehicles that range from low to high lift-to-drag ratio configurations.

Wilhite, A. W.↗
NASA NTRS1983

Booster and orbiter configurations

In the recent Future Space Transportation System (FSFS) study, a mission model was selected and a baseline vehicle which best met model requirements was shaped. This baseline was then analyzed for flight performance, structural and subsystem weight, and operation. Figures related to a payload of 150,000 lb in a 20-ft-diam by 90-ft-long envelope became the baseline. The existence of both space-based orbital transfer vehicles (OTVs) and a space station was assumed, taking into account a transfer of the payload from the launch vehicle to OTVs at the space station for final delivery to geosynchronous orbit (GEO). A computer-aided engineering system called Aerospace Vehicle Interactive Design (AVID) was employed in connection with baseline vehicle development. It was found that approximately three-fifth of the payload weight would be cryogenic propellants for OTVs. Attention is given to problems regarding the packaging of cryogenic tankage, a payload shroud, and studies of staging for two different booster propulsion units.

Wilhite, A. W.↗
NASA NTRS1983

Integrating computer programs for engineering analysis and design

The design of a third-generation system for integrating computer programs for engineering and design has been developed for the Aerospace Vehicle Interactive Design (AVID) system. This system consists of an engineering data management system, program interface software, a user interface, and a geometry system. A relational information system (ARIS) was developed specifically for the computer-aided engineering system. It is used for a repository of design data that are communicated between analysis programs, for a dictionary that describes these design data, for a directory that describes the analysis programs, and for other system functions. A method is described for interfacing independent analysis programs into a loosely-coupled design system. This method emphasizes an interactive extension of analysis techniques and manipulation of design data. Also, integrity mechanisms exist to maintain database correctness for multidisciplinary design tasks by an individual or a team of specialists. Finally, a prototype user interface program has been developed to aid in system utilization.

Wilhite, A. W.↗
NASA NTRS1982

Advanced rocket propulsion technology assessment for future space transportation

Single-stage and two-stage launch vehicles were evaluated for various levels of propulsion technology and payloads. The evaluation included tradeoffs between ascent flight performance and vehicle sizing that were driven by engine mass, specific impulse, and propellant requirements. Numerous mission, flight, and vehicle-related requirements and constraints were satisfied in the design process. The results showed that advanced technology had a large effect on reducing both single- and two-stage vehicle size. High-pressure hydrocarbon-fueled engines that were burned in parallel with two-position nozzle hydrogen-fueled engines reduced dry mass by 23% for the two-stage vehicle and 28% for the single-stage vehicle as compared to an all-hydrogen-fueled system. The dual-expander engine reduced single-stage vehicle dry mass by 41%. Using advanced technology, the single-stage vehicle became comparable in size and sensitivity to that of the two-stage vehicle for small payloads.

Wilhite, A. W.↗
NASA NTRS1982

Optimum wing sizing of a single-stage-to-orbit vehicle

An investigation has been conducted to determine preliminary wing designs for a single-stage-to-orbit (SSTO) vehicle. This vehicle has the following mission profile: vertical takeoff, boost-to-orbit, hypersonic reentry, and horizontal landing. For this vehicle, the wing is sized to meet Space Shuttle reentry aerodynamic requirements for hypersonic trim and horizontal landing, since reentry trajectories for the Shuttle and the SSTO vehicle are similar. A hypersonic and subsonic aerodynamic computer program was developed and combined with an existing optimization algorithm to automatically size and shape a wing which satisfies both reentry and landing requirements while also maintaining a minimum mass design. With this procedure, the influence of hypersonic and subsonic aerodynamic requirements, control surface size, and center-of-gravity positions on the initial wing design were investigated.

Wilhite, A. W.↗
NASA NTRS1981

The Aerospace Vehicle Interactive Design system

The aerospace vehicle interactive design (AVID) is a computer aided design that was developed for the conceptual and preliminary design of aerospace vehicles. The AVID system evolved from the application of several design approaches in an advanced concepts environment in which both mission requirements and vehicle configurations are continually changing. The basic AVID software facilitates the integration of independent analysis programs into a design system where the programs can be executed individually for analysis or executed in groups for design iterations and parametric studies. Programs integrated into an AVID system for launch vehicle design include geometry, aerodynamics, propulsion, flight performance, mass properties, and economics.

Wilhite, A. W.↗
NASA NTRS1981

The Aerospace Vehicle Interactive Design system

The Aerospace Vehicle Interactive Design (AVID) is a computer-aided design system that was developed for the conceptual and preliminary design of aerospace vehicles. The AVID system evolved from the application of several design approaches in an advanced concepts environment in which both mission requirements and vehicle configurations are continually changing. The basic AVID software facilitates the integration of independent analysis programs into a design system where the programs can be executed individually for analysis or executed in groups for design iterations and parametric studies. Programs that have been integrated into an AVID system for launch vehicle design include geometry, aerodynamics, propulsion, flight performance, mass properties, and economics.

Wilhite, A. W.↗
NASA NTRS1979

Effects of relaxed static longitudinal stability on a single-stage-to-orbit vehicle design

The effects of relaxing longitudinal stability requirements on single stage to orbit space vehicles is studied. A comparison of the mass and performance characteristics of two vehicles, one designed for positive levels of longitudinal stability and the other designed with relaxed stability requirements in a computer aided design process is presented. Both vehicles, required to meet the same mission characteristics are described. Wind tunnel tests, conducted over a Mach number range from 0.3 to 4.63 to verify estimated aerodynamic characteristics, are discussed.

Freeman, D. C., Jr.↗
NASA NTRS1979

AVID - A design system for technology studies of advanced transportation concepts

The basic AVID (Aerospace Vehicle Interactive Design) is a general system for conceptual and preliminary design currently being applied to a broad range of future space transportation and spacecraft vehicle concepts. AVID hardware includes a minicomputer allowing rapid designer interaction. AVID software includes (1) an executive program and communication data base which provide the automated capability to couple individual programs, either individually in an interactive mode or chained together in an automatic sequence mode; and (2) the individual technology and utility programs which provide analysis capability in areas such as graphics, aerodynamics, propulsion, flight performance, weights, sizing, and costs.

Wilhite, A. W.↗
NASA NTRS1979

Dual-fuel propulsion - Why it works, possible engines, and results of vehicle studies

The reasons why dual-fuel propulsion works are discussed. Various engine options are discussed, and vehicle mass and cost results are presented for earth-to-orbit vehicles. The results indicate that dual-fuel propulsion is attractive, particularly with the dual-expander engine. A unique orbit-transfer vehicle is described which uses dual-fuel propulsion. One Space Shuttle flight and one flight of a heavy-lift Shuttle derivative are used for each orbit-transfer vehicle flight, and the payload capability is quite attractive.

Martin, J. A.↗
NASA NTRS1978

Optimization and evaluation of main liquid rocket propulsion systems for advanced earth-to-orbit shuttles

A computerized preliminary design system is used to evaluate potential main liquid-rocket propulsion systems for advanced technology winged single-stage-to-orbit launch vehicles. Evaluated are trade-offs between ascent flight trajectory performance and flight vehicle sizing driven by engine mass and propellant requirements. Numerous mission, flight, and vehicle-related requirements and constraints are satisfied in the design process. With the design system, five dual-mode propulsion system concepts are compared to a baseline hydrogen and oxygen system in terms of the changes in vehicle dry mass and gross mass.

Wilhite, A. W.↗
NASA NTRS1977

Analysis of separation of the space shuttle orbiter from a large transport airplane

The feasibility of safely separating the space shuttle orbiter (140A/B) from the top of a large carrier vehicle (the C-5 airplane) at subsonic speeds was investigated. The longitudinal equations of motion for both vehicles were numerically integrated using a digital computer program which incorporates experimentally derived interference aerodynamic data to analyze the separation maneuver for various initial conditions. Separation of the space shuttle orbiter from a carrier vehicle was feasible for a range of dynamic-pressure and flight-path-angle conditions. By using an autopilot, the vehicle attitudes were held constant which ensured separation. Carrier-vehicle engine thrust, landing gear, and spoilers provide some flexibility in the separation maneuver.

Wilhite, A. W.↗
NASA NTRS1976

Nozzle selection for optimized single-stage shuttles

A computerized preliminary design procedure has been used to determine rocket-engine bell-nozzle configurations which achieve either minimum gross mass or minimum dry mass on an advanced technology winged single-stage-to-orbit launch vehicle. This procedure evaluates the trade offs between the optimized ascent flight trajectory performance and the flight vehicle sizing driven by the engine mass and propellant requirements. Numerous mission, flight, and vehicle related requirements and constraints are satisfied in this process. Propulsion system configurations which incorporate dual-position nozzles are evaluated and compared to configurations using all fixed nozzles.

Eldred, C. H.↗