Engineering topics

Whittenberger, J. Daniel

Publications and source records attributed to Whittenberger, J. Daniel.

At least 37 records · Page 2

NASA NTRS1995

Elevated temperature creep properties of NiAl cryomilled with and without Y2O3

The creep properties of lots of NiAl cryomilled with and without Y2O3 have been determined in compression and tension. Although identical cryomilling procedures were used, differences in composition were found between the lot ground with 0.5 vol% yttria and the lot ground without Y2O3. Compression testing between 1000 and 1300 K yielded similar creep strengths for both materials, while tensile creep rupture testing indicated that the yttria-containing alloy was slightly stronger than the Y2O3-free version. Both compression and tensile testing showed two deformation regimes; whereas the stress state did not affect the high stress exponent (n approximately equals 10) mechanism, the low stress exponent regime n was approximately 6 in tension and approximately 2 in compression. The strengths in tension were somewhat less than those measured in compression, but the estimated activation energies (Q) of approximately 600 kJ/mol for tensile testing were closer to the previously measured values (approximately 700 kJ/mol) for NiAl-AlN and very different from the Q's of 400 and 200 kJ/mol for compression tests in the high and low stress exponent regimes, respectively. A Larson-Miller comparison indicated that cryomilling can produce an alloy with long-term, high-temperature strength at least equal to conventional superalloys.

Whittenberger, J. Daniel↗

NASA NTRS1995

The 1200 K compressive properties of N-containing NiAl

As part of a series of experiments to understand the role of N on the strength of NiAl, a heat of NiAl was enriched with N by melting and atomization to powder in a nitrogen atmosphere. Following consolidation of the powder by hot extrusion, 1200 K compressive properties were measured in air. Within the range of strain rates examined, 10(exp -3) to 10(exp -9) s(exp -1), the strength of the N-enriched NiAl was greater than that of a simple 15 micron grain size polycrystalline, binary NiAl alloy. For the most part the overall improvement in strength is ascribed to the fine grain size of the N-doped NiAl rather than the alloy chemistry; however, the alloy displayed a complex behavior exhibiting both weakening effects as well as strengthening ones.

Whittenberger, J. Daniel↗

NASA NTRS1990

Mechanical strength and thermophysical properties of PM212: A high temperature self-lubricating powder metallurgy composite

A powder metallurgy composite, PM212, composed of metal bonded chromium carbide and solid lubricants is shown to be self-lubricating to a maximum application temperature of 900 C. The high temperature compressive strength, tensile strength, thermal expansion and thermal conductivity data needed to design PM212 sliding contact bearings and seals are reported for sintered and isostatically pressed (HIPed) versions of PM212. Other properties presented are room temperature density, hardness, and elastic modulus. In general, both versions appear to have adequate strength to be considered as sliding contact bearing materials, but the HIPed version, which is fully dense, is much stronger than the sintered version which contains about 20 percent pore volume. The sintered material is less costly to make, but the HIPed version is better where high compressive strength is important.

Edwards, Phillip M.↗

NASA NTRS1990

1300 K compressive properties of a reaction milled NiAl-AlN composites

When B2 crystal-structure nickel aluminide is subjected to high-intensity mechanical ball milling in a liquid nitrogen bath, or 'cryomilling', an NiAl composite is obtained which contains about 10 vol pct AlN particles. This composition arises from the incorporation of N during cryomilling; during subsequent thermomechanical processing, the N reacts with Al. While compressive testing of extruded or isostatically pressed specimens at 1300 K indicated that strength at relatively fast strain rates is slightly dependent on consolidation method, slower strain rates indicate no clear dependency on densification technique: four different consolidation methods were found to yield similar creep strengths. The creep properties of NiAl-AlN are similar to those of the single-crystal Ni-base superalloy NASAIR 100.

Whittenberger, J. Daniel↗

NASA NTRS1990

Tensile properties of HA 230 and HA 188 after 400 and 2500 hour exposures to LiF-22CaF2 and vacuum at 1093 K

The solid-to-liquid phase transformation of the nominal LiF-20CaF2 eutectic at 1043 K is considered to be an ideal candidate thermal energy storage mechanism for a space based low temperature Brayton cycle solar dynamic system. Although Co, Fe, and Ni superalloys are thought to be suitable containment materials for LiF based salts, long term containment is of concern because molten fluorides are usually corrosive and Cr can be lost into space through evaporation. Two examples of commercially available superalloys in sheet form, the Ni-base material HA 230 and the Co-base material Ha 88, have been exposed to molten LiF-22CaF2, its vapor, and vacuum, at 1093 K, for 400 and 2500 hr. Triplicate tensile testing of specimens subjected to all three environments have been undertaken between 77 to 1200 K. Comparison of the weight gain data, microstructure, and tensile properties indicate that little, if any, difference in behavior can be ascribed to the exposure environment.

Whittenberger, J. Daniel↗

NASA NTRS1990

1300 K compressive properties of several dispersion strengthened NiAl materials

To examine the potential of rapid solidification technology (RST) as a means to fabricate dispersion-strengthened aluminides, cylindrical compression samples were machined from the gauge section of their tensile specimens and tested in air at 1300 K. While microscopy indicates that RST can produce fine dispersions of TiB2, TiC and HfC in a NiAl matrix, the mechanical property data reveal that only HfC successfully strengthens the intermetallic matrix. The high stress exponents (above 10) and/or independence of strain rate on stress for NiAl-HfC materials suggest elevated temperature mechanical behavior similar to that found in oxide dispersion-strengthened alloys. Furthermore, an apparent example of departure side pinning has been observed, and as such, it is indicative of a threshold stress for creep.

Whittenberger, J. Daniel↗

NASA NTRS1990

Preliminary investigation of a NiAl composite prepared by cryomilling

An attempt has been made to improve the high temperature mechanical strength of the B2 cubic crystal structure intermetallic NiAl by dispersion strengthening. Prealloyed Ni-51 at. pct Al was cryomilled with a Y2O3 addition to form an yttria dispersoid within the intermetallic matrix. Following milling, the powder was hot extruded to full density and machined into test coupons. Compression testing between 1200 and 1400 K indicated that the cryogenic process yielded the strongest NiAl based material tested to date. Creep resistance was six times better than NiAl and twice that of a NiAl particulate composite containing 10 vol pct TiB2. Surprisingly, transmission electron microscopy revealed that the second phase was inhomogeneously distributed. Furthermore, X-ray analysis indicated that the second phase was not Y2O3 but rather AlN.

Whittenberger, J. Daniel↗

NASA NTRS1990

Intergranular fracture of lithium fluoride-22 percent calcium fluoride hypereutectic salt at 800 K

Substantial strain-hardening was noted during the initial stages of deformation in constant-velocity compression tests conducted on as-cast samples of the LiF-22 mol pct CaF2 hypereutectic salt at 800 K. The deformed specimens exhibited extensive grain-boundary cracking and cavitation, suggesting that such cracking, in conjunction with interfacial sliding, is important for cavity nucleation at grain boundaries and at the LiF-CaF2 interfaces. Cavity growth and interlinkage occur through the preferential failure of the weaker LiF phase.

Raj, Subramanium V.↗

NASA NTRS1990

Solid state processing for high temperature alloys and composites

A variety of solid state powder processing methods have been examined for their potential to produce high temperature materials. These techniques included solid state diffusion, mechanical alloying, reaction milling, and exothermic reactions. While both mechanical alloying and exothermic reactions are capable of producing high temperature composites in addition to yielding solid solution and precipitation hardened alloys, reaction milling can only be used to make composite materials. Although at present this method has only been applied to make carbide strengthened Al, recent work indicates that reaction milling is capable of yielding high strength NiAl-AlN composites.

Whittenberger, J. Daniel↗

NASA NTRS1990

Elevated temperature slow plastic deformation of NiAl-TiB2 particulate composites at 1200 and 1300 K

Elevated temperature compression testing has been conducted in air at 1200 and 1300 K with strain rates varying from about 10 to the -4th to about 10 to the -7th/sec on NiAl-TiB2 particulate composites. These materials, which consisted of a B2 crystal structure intermetallic Ni-50 at. pct Al matrix and from 0 to 30 vol pct of approximately 1- micron diameter TiB2 particles, were fabricated by XD synthesis and hot pressed to full density. Flow strength of the composites increased with volume fraction of the strengthening phase with NiAl-30TiB2 being approximately three times stronger than NiAl. Comparison of the light optical and TEM microstructures of as-received and tested samples revealed that reactions did not occur between the two phases, and NiAl-TiB2 interfaces were not cracked during deformation. Additional TEM indicated that the particles stabilize a vastly different microstructure in the NiAl matrix of the composites than that formed in unreinforced NiAl.

Whittenberger, J. Daniel↗

NASA NTRS1989

1100 to 1300 K slow plastic compression properties of Ni-38.5Al composites

Compressive properties of Ni-38.5Al (in at. pct) composites containing 4, 7.5, and 15 vol pct Al2O3 whiskers or 20 vol pct TiB2 particles were investigated in samples compacted to full density by vacuum hot pressing at 20.7 MPa and 1725 K, followed by HIP at 207 MPa and 1725 K. Constant-velocity compression tests were conducted in air at 1100, 1200, and 1300 K to 8 percent strain. It was found that the elevated-temperature compressive properties of Ni-38.5Al+Al2O3 whisker composites were only marginally better than those of the matrix, and that the composite containing 20 vol pct TiB2 particles was only slightly stronger than unreinforced Ni-38.5Al.

Whittenberger, J. Daniel↗

NASA NTRS1989

Compressive strength of a B2 matrix NiAl-Nb intermetallic at 1200 and 1300 K

The effect of a large Nb addition to a NiAl, to a final composition 43.5Ni-45.2Al-0.8Fe-10.5Nb (in at. pct), on the high-temperature compressive strength of NiAl was investigated using cylindrical samples which were compression tested in air at 1200 K and 1300 K under constant-velocity conditions. The compressive strength of the Ni-45Al-10.5Nb was compared to data from all known solid solution-strengthened and/or precipitation-strengthened NiAl-based materials. It was found that, for strain rates higher than 5 x 10 to the -6th/sec, the Ni-45Al-10.5Nb is stronger than NiAl. However, this advantage disappears at lower strain rates. A comparison of NiAl-based materials indicated that a NiAl+TiB2 composite containing 20 vol pct 1-micron-diam particles has a strength superiority over all the solid solution and precipitation-hardened aluminides at strain rates below 10 to the -7th/sec.

Whittenberger, J. Daniel↗

NASA NTRS1989

1200 to 1400 K slow strain rate compressive behavior of small grain size NiAl/Ni2AlTi alloys and NiAl/Ni2AlTi-TiB2 composites

In order to impart ductility into NiAl-Ni2AlTi alloys, small grain size single (Ni-45Al-5Ti) and two (Ni-40Al-10Ti) phase intermetallics are fabricated by a process which yields fine microstructures in NiAl. The results of a study of elevated temperature compressive properties of two small grain size NiAl-Ni2AlTi alloys are then described. In addition, the behavior of the Ti-modified nickel aluminides with 20 vol pct TiB2 particles of approximately 1 micron in diameter is also investigated, since these compositions have the potential for being the matrix material in high temperature particulate-strengthened composites.

Whittenberger, J. Daniel↗

NASA NTRS1989

Properties of oxide dispersion strengthened alloys

A contrast is drawn between the behavior of ODS alloys' matrix compositions and that of more conventional alloys. Mechanical property enhancements associated with ODS alloys are accounted for by both the presence of the dispersoids and, in some cases, the smaller size and number of secondary phases. Data obtained for ODS materials to date indicate the presence of three different threshold stresses, due to dislocation-particle interactions, diffusional creep/grain boundary sliding, and, in the case of the MA 956 ODS alloy, crack nucleation and growth processes. It is critical to establish which threshold stress is in effect, since the latter two stresses can result in failure by cracking.

Whittenberger, J. Daniel↗

NASA NTRS1989

1200 to 1400 K slow strain rate compressive properties of NiAl/Ni2AlTi-base materials

An attempt to apply the Martin Marietta Corporation's XD technology to the fabrication of NiAl-Ni2AlTi materials with improved creep properties is presented. Composite materials, containing from 0 to 30 vol pct of nominally 1-micron-diameter TiB2 particles in the intermetallic matrix have been produced by the XD process and compacted by hot pressing. Such composites demonstrated significant strength increases, approaching 3-fold for the 20 vol pct materials, in comparison to the unreinforced aluminide. This behavior was accomplished without deleterious side effects as the grain boundaries and particle-matrix interfaces were intact after compressive deformation to 10 percent or more strain. Typical true compressive stress-strain diagrams for materials tested in air between 1200 and 1400 K at approximate strain rates of 1.7 x 10 to the -6th/sec are presented.

Whittenberger, J. Daniel↗

NASA NTRS1988

The influence of grain size and composition on 1000 to 1400 K slow plastic flow properties of NiAl

The compressive slow plastic flow behavior of several B2 crystal structure NiAl intermetallics has been studied in air between 1000 and 1400 K. Small grain-sized Ni-48.25 at. pct Al (of about 10 microns) was found to be stronger than the previously studied 17 microns diameter material. While grain refinement improved the strength at all test temperatures, the exact mechanism is not clear. Experiments at lower temperature revealed that composition as well as grain size can be an important factor, since Ni-49.2Al was weaker than Ni-48.25Al. Pronounced yield points were found during slow strain-rate testing at 1000 K; however, continued deformation appears to take place by the same mechanism(s) as found at high temperatures. Small changes in thermomechanical processing (TMP) schedules to fabricate Ni-49.2Al indicated that basic deformation characteristics (stress exponent and activation energy) are not affected; however, the preexponential term could be modified if TMP alters the grain structure.

Whittenberger, J. Daniel↗

NASA NTRS1988

Elevated temperature slow plastic deformation of NiAl/TiB2 particulate composites

The 'XD' process for production of discontinuously-reinforced metal-matrix composites has been used to enhance the high-temperature strength of NiAl-TiB2 composites with particulate densities of up to 30 vol pct. SEM, TEM, and optical characterizations of the resulting microstructures showed the average TiB2 particle size to be about 1 micron, while the average grain of the NiAl matrix was of the order of 10 microns. Elevated temperature compression tests conducted at 1200 and 1300 K indicated flow strengths to increase with TiB2 content, so that the 20 vol pct TiB2-reinforced composite was three times stronger than the unreinforced NiAl; this is ascribed to the very high density of microstructural tangled dislocations, loops, and subgrain boundaries connecting the particles.

Whittenberger, J. Daniel↗

NASA NTRS1987

Preliminary investigation of inertia friction welding B2 aluminides

An attempt is made to achieve inertia friction-welding in FeAl and NiAl samples, taking into account their intermetallics' compositions, extrusion parameters, and microstructural data. The energy required for the weld is stored in a rotating flywheel mass attached to one of the two pieces to be joined; when enough energy is introduced, the flywheel is disconnected and an axial load is applied which forces the spinning piece against the stationary one, converting the energy into heat by means of friction. Due to the inherent brittleness of the aluminides, a step-load program was used in which an initial, low-pressure heat buildup increased the work pieces' ductility.

Whittenberger, J. Daniel↗