Engineering topics

Whittenberger, J. D.

Publications and source records attributed to Whittenberger, J. D..

At least 37 records · Page 2

NASA NTRS1993

Stress relaxation of low pressure plasma-sprayed NiCrAlY alloys

The stress relaxation behavior of three NiCrAlY alloys that are commonly used as bond coats for thermal barrier coatings (TBCs) has been directly measured. The relaxation study was conducted at temperatures of 800-1000 C and over a wide range of stresses. It was established that all three bond coat alloys relaxed quite rapidly at temperatures of 900 C and above. Since the upper use temperatures for bond coats in gas turbine engines are between 900 and 1000 C, bond coat relaxation is expected to occur in service. Therefore, relaxation of the bond coat has the potential to affect TBC life. Furthermore, the relaxation differences observed between the three alloys offers a possible explanation for the differences in TBC life observed for these bond coats. While bond coat relaxation is expected to occur for a TBC in service, the mechanism for a relaxation effect on TBC life, if it exists, is yet to be determined.

Brindley, W. J.↗

NASA NTRS1993

Stress relaxation of low pressure plasma-sprayed NiCrAlY alloys

Brindley, W. J.↗

NASA NTRS1993

Characteristics of an Elevated Temperature ALN Particulate Reinforced NiAl

High energy milling of NiAl in liquid nitrogen (cryomilling) leads to the formation of a discontinuously AlN particle reinforced aluminide which has shown good potential as a high strength oxidation resistant material. Experiments have demonstrated that cryomilling is repeatable, and materials with reproducible chemistries and mechanical properties result. Furthermore, it is possible to vary the AlN content through control of the milling parameters. Tensile creep as well as compressive creep testing has been undertaken on a lot of NiAl-AlN. While this material is weaker in tension than compression, the tensile strength is respectable: for example, the creep rupture life exceeds 2700 h at 1300 K, 50 MPa. Heat treatment of the particulate reinforced aluminide at 1600 K promotes AlN growth which weakens the material but does not change the deformation mechanism. Cyclic oxidation testing of lots of NiAl-AlN which were cryomilled with and without yttria reveal that Y2O3 promotes better oxidation resistance. However, the presence or absence of yttria had no affect on the mechanical properties.

Whittenberger, J. D.↗

NASA NTRS1992

Elevated temperature compressive properties of reaction milled NiAl-AlN and Zr-doped NiAl-AlN composites

Previous studies of a single lot of NiAl powder which had been ground under high intensity conditions in liquid nitrogen (cryomilling) indicated that this processing leads to a high strength, elevated temperature NiAl-AlN composite. Because this was the first known example of the use of the reaction milling process to produce a high temperature composite, the reproducibility of this technique was unknown. Two additional lots of NIAl powder and a lot of a Zr-doped NiAl powder have been cryomilled, and analyses indicate that AlN was formed within a NiAl matrix in all three cases. Compression testing between 1200 K and 1400 K has shown that the deformation resistance of these heats is similar to that of the first lot of NiAl-AlN; thus cryomilling can improve the creep resistance of NiAl by a factor of six. Based on this work, it is concluded that cryomilling of NiAl powder to form high temperature, high strength NiAl-AlN composites is a reproducible process.

Whittenberger, J. D.↗

NASA NTRS1992

Mechanical properties of Haynes Alloy 188 after exposure to LiF-22CaF2, air, and vacuum at 1093 K for periods up to 10,000 hours

As part of a program to provide reassurance that the cobalt-base superalloy Haynes Alloy 188 can adequately contain a LiF-CaF2 eutectic thermal energy storage salt, 4900- and 10,000-hr exposures of Haynes Alloy 188 to LiF-22CaF2, its vapor, vacuum, and air at 1093 K have been undertaken. Following such exposures, the microstructure has been characterized and the 77 to 1200 K tensile properties measured. In addition, 1050 K vacuum creep-rupture testing of as-received and molten salt- and vacuum-exposed samples has been undertaken. Although slight degradation of the mechanical properties of Haynes Alloy 188 due to prior exposure was observed, basically none of the losses could be ascribed to a particular environment. Hence, observed decreases in properties are due to thermal aging effects, not corrosive attack. In view of these findings, Haynes Alloy 188 is still deemed to be suitable for containment of the eutectic LiF-CaF2 thermal energy storage media.

Whittenberger, J. D.↗

NASA NTRS1992

1400 and 1500 K Compressive Creep Properties of an NiAl/AlN Composite

Compressive creep properties of an NiAl/AlN(p) composite produced by a reaction milling process were investigated at 1400 and 1500 K and at slow strain rates, to investigate the relative strength of this composite at high temperatures, and to determine if the consolidation technique affects the 1400 K creep properties. Results indicate that the stress exponent of the NiAl/AlN(p) composite was similar to that for unreinforced NiAl. However, the activation energy for the composite was found to be more than twice that measured in the unreinforced matrix. Oxidation did not affect the composite at 1400 K, but a significant attack was observed in a sample subjected to fast deformation at 1500 K.

Whittenberger, J. D.↗

NASA NTRS1992

Interdiffusion between the L1(2) trialuminides Al66Ti25Mn9 and Al67Ti25Cr8

Concentration-distance profiles obtained from Al66Ti25Mn9/Al67Ti25Cr8 diffusion couples are used to determine the interdiffusion coeffients in the temperature range 1373-1073 K. The couples are treated as pseudobinaries, and the diffusion coefficients are determined using the Matano approach. The results are then used to compute the activation energies for diffusion, and a comparison is made with some existing data for the activation energy for creep of Al22Ti8Fe3.

Kumar, K. S.↗

NASA NTRS1992

Composites of low-density trialuminides: Particulate and long fiber reinforcements

An examination of the ternary L1(sub 2) trialuminides, Al66Ti25Mn9, Al67Ti25Cr8, and Al22Ti8Fe3 in compression, bending, and tension revealed that none of these compounds exhibited a desirable balance of strength, ductility, and oxidation resistance. Subsequently, specific quaternary and quinary compositions were cast, homogenized, and isothermally forged. Both, the monolithic material and its particulate reinforced counterparts were examined in compression, three point bend, and tension as a function of temperature, and at high temperatures as a function of strain rate. An alternate approach that was examined in this program to enhance the low temperature damage tolerance of these materials was to incorporate long refractory metal wires in the matrix. In summary, it appears that of the various matrix compositions examined, ternary Al66Ti25Mn9 exhibits the best balance in strength, ductility, and oxidation resistance. Although the idea of refractory metal wire reinforcement is an attractive one, a successful combination remains to be identified.

Kumar, K. S.↗

NASA NTRS1992

Discontinuously reinforced intermetallic matrix composites via XD synthesis

A review is given of recent results obtained for discontinuously reinforced intermetallic matrix composites produced using the XD process. Intermetallic matrices investigated include NiAl, multiphase NiAl + Ni2AlTi, CoAl, near-gamma titanium aluminides, and Ll2 trialuminides containing minor amounts of second phase. Such mechanical properties as low and high temperature strength, compressive and tensile creep, elastic modulus, ambient ductility, and fracture toughness are discussed as functions of reinforcement size, shape, and volume fraction. Microstructures before and after deformation are examined and correlated with measured properties. An observation of interest in many of the systems examined is 'dispersion weakening' at high temperatures and high strain rates. This behavior is not specific to the XD process; rather similar observations have been reported in other discontinuous composites. Proposed mechanisms for this behavior are presented.

Kumar, K. S.↗

NASA NTRS1992

Compressive strength of directionally solidified NiAl-NiAlNb intermetallics at 1200 and 1300 K

Results are presented from measurements of 1200 K and 1300 K compressive properties of two directionally solidified NiAl-NiAlNb compositions (in at. pct): Ni-41.75Al-16.5Nb (eutectic composition) and Ni-47.5Al-8.9Nb-1.3C (Al-rich composition). Results showed that the strength of the eutectic was a factor of 2 greater than that of the Al-rich composition. However, the analysis of the compressive stress-strain data indicated that the deformation mechanism was the same in both materials.

Whittenberger, J. D.↗

NASA NTRS1992

Influence of grain size on the creep behavior of HfC-dispersed NiAl

Rapid solidification technology has been utilized to produce a NiAl-4(wt pct)HfC composite containing about 0.3 vol pct HfC as dispersed 50 nm particles. Study of the 1300 K compressive creep properties demonstrated that the initial, small grain size microstructure was unstable under slow strain rate deformation conditions. The grain growth which occurred during testing led to considerable strengthening. Subsequent measurements of the creep properties of the coarse grained specimens revealed that this strength was achieved by a large increase in the activation energy for deformation without any change in the stress exponent. Based on this work, it is concluded that large grain microstructures will be required for optimum elevated temperature creep properties in dispersed NiAl.

Whittenberger, J. D.↗

NASA NTRS1991

1000 to 1200 K time-dependent compressive deformation of single-crystalline and polycrystalline B2 Ni-40Al

The 1000-K and 1200-K time-dependent deformation of 100-line-oriented and non-100-line-oriented single crystals of Ni-40Al (made by a modified Bridgman technique) was examined over a large range of strain rates (from 0.1 to 10 to the -7th per sec). The results were compared with those for polycrystalline Ni-40Al made by hot pressing XD synthesized powder. The results from measurements of slow-plastic-strain-rate properties of the two materials show that single crystals offer no strength advantage over polycrystalline material. Both forms were found to deform via a dislocation climb mechanism.

Whittenberger, J. D.↗

NASA NTRS1991

Slow strain rate 1200-1400 K compressive properties of NiAl-1Hf

Compression tests are conducted on NiAl-1Hf to assess the elevated-temperature creep behavior of this precipitation-hardened aluminide. While the strength is high under fast strain rates (more than 10 exp -5/s), under slower conditions the alloy is weak. Thus, it is unlikely that effective creep resistance can be obtained in NiAl through small Hf additions.

Whittenberger, J. D.↗

NASA NTRS1991

1000 to 1300 K slow plastic compression properties of Al-deficient NiAl

Nickel aluminides containing 37, 38.5 and 40 at. pct Al have been fabricated by XD synthesis and hot pressing. Such materials were compression tested in air under constant velocity conditions between 1000 and 1300 K. Examination of the microstructures of hot pressed and compression tested aluminides indicated that the structure consisted of two phases, gamma-prime and NiAl, for essentially all conditions, where gamma-prime was usually found on the NiAl grain boundaries. The stress-strain behavior of all three intermetallics was similar where flow at a nominally constant stress occurred after about two-percent plastic deformation. Furthermore, the 1000 to 1300 K flow stress-strain rate properties are nearly identical for these materials, and they are much lower than those for XD processed Ni-50Al. The overall deformation of the two phase nickel aluminides appears to be controlled by dislocation climb in NiAl rather than processes in gamma-prime.

Whittenberger, J. D.↗

NASA NTRS1991

Compression behavior of TiB2-particulate-reinforced composites of Al22Fe3Ti8

The compression behavior of both the monolithic L1(2) compound Al22Fe3Ti8 and discontinuous composites obtained by incorporating about 1 micron TiB2 particles was studied for various volume percent reinforcements as a function of temperature and at high temepratures as a function of strain rate. In this study, by varying the Fe and Ti contents, the nature and volume fraction of the minor phases coexisting with the dominant L1(2) phase were changed and were examined with and without TiB2 reinforcement. At high strain rates, the TiB2 reinforcements significantly enhance ambiant and warm-temperature strength, although a crossover is observed at about 1000 K, above which the monolithic material is stronger than the composite. At slow strain rates representative of creep conditions, however, the TiB2-containing composites retain their superiority at least up to 1200 K.

Dipietro, M. S.↗

NASA NTRS1991

Low-density, high-strength intermetallic matrix composites by XD (trademark) synthesis

A feasibility study was conducted to evaluate the potential of particulate composites based on low-density, L1(sub 2) trialuminide matrices for high-temperature applications. The compounds evaluated included Al22Fe3Ti8 (as a multiphase matrix), Al67Ti25Cr8, and Al66Ti25Mn9. The reinforcement consisted of TiB2 particulates. The TiB2 composites were processed by ingot and powder metallurgy techniques. Microstructural characterization and mechanical testing were performed in the hot-pressed and hot-isostatic-pressed condition. The casting were sectioned and isothermally forged into pancakes. All the materials were tested in compression as a function of temperature, and at high temperatures as a function of strain rate. The test results are discussed.

Kumar, K. S.↗

NASA NTRS1991

Compression, bend, and tension studies on forged Al67Ti25Cr8 and Al66Ti25Mn(g) L1(2) compounds

Cast, homogenized, and isothermally forged aluminum-rich L1(2) compounds Al67Ti25Cr8 and Al66Ti25Mn(g) were tested in compression as a function of temperature and as a function of strain rate at elevated temperatures (1000 K and 1100 K). Three-point bend specimens were tested as a function of temperature in the range 300 K to 873 K. Strain gages glued on the tensile side of the ambient and 473 K specimens enabled direct strain measurements. A number of 'buttonhead' tensile specimens were electro-discharge machined, fine polished, and tested between ambient and 1073 K for yield strength and ductility as a function of temperature. Scanning electron microscope (SEM) examination of fracture surfaces from both the bend and tensile specimens revealed a gradual transition from transgranular cleavage to intergranular failure with increasing temperature.

Kumar, K. S.↗

NASA NTRS1991

Does a threshold stress for creep exist in HfC-dispersed NiAl?

Recently it was proposed (Jha et al., 1989; Whittenberger et al., 1990) on the basis of constant velocity testing at 1300 K that dispersion strengthened NiAl composites containing about 4 wt pct HfC possess threshold stresses for creep. Further, 1300 K compression testing has been conducted on NiAl+4HfC, and diametrically opposite behavior has been found: for constant load creep tests a normal power law behavior was observed. However, additional constant velocity testing still indicates that the flow stress is essentially independent of strain rate below 10 exp -6/s. Examination of NiAl+4.3HfC specimens deformed under constant velocity conditions revealed that the original hot extruded small grain structure could be converted to large, elongated grains during testing. Such a transformation appears to be responsible for the apparent threshold stress behavior in HfC dispersed NiAl.

Whittenberger, J. D.↗