Engineering Papers⌕ Search

Engineering topics

White, P. R.

Publications and source records attributed to White, P. R..

11 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Fluid flow meter for measuring the rate of fluid flow in a conduit

A tube fluid flow rate meter consists of a reservoir divided by flexible diaphragm into two separate isolated compartments. The incoming and outgoing tubes open into the compartments. The orifice is sized to allow maximum tube fluid flow. Opposing compression springs are secured within the two compartments on opposite sides of the orifice to maintain orifice position when the tube fluid pressure is zero. A tapered element is centered in, and extends through the orifice into the compartment, leaving an annular opening between the element and the perimeter of the oriface. The size varies as the diaphragm flexes with changes in the tube fluid pressure to change the fluid flow through the opening. The light source directs light upon the element which in turn scatters the light through the opening into the compartment. The light detector in the compartment senses the scattered light to generate a signal indicating the amount of fluid.

White, P. R.↗
NASA NTRS1986

Flowmeter for Clear Fluids

Electronic flowmeter measures flow rate of clear or translucent fluids. Instrument produces electrical signal proportional to volume of fluid flowing through it per unit time. Optoelectronic instrument generates electrical signal proportional to fluid-flow rate.

White, P. R.↗
NASA NTRS1985

Application of a personal computer for the uncoupled vibration analysis of wind turbine blade and counterweight assemblies

A research effort was undertaken to develop personal computer based software for vibrational analysis. The software was developed to analytically determine the natural frequencies and mode shapes for the uncoupled lateral vibrations of the blade and counterweight assemblies used in a single bladed wind turbine. The uncoupled vibration analysis was performed in both the flapwise and chordwise directions for static rotor conditions. The effects of rotation on the uncoupled flapwise vibration of the blade and counterweight assemblies were evaluated for various rotor speeds up to 90 rpm. The theory, used in the vibration analysis codes, is based on a lumped mass formulation for the blade and counterweight assemblies. The codes are general so that other designs can be readily analyzed. The input for the codes is generally interactive to facilitate usage. The output of the codes is both tabular and graphical. Listings of the codes are provided. Predicted natural frequencies of the first several modes show reasonable agreement with experimental results. The analysis codes were originally developed on a DEC PDP 11/34 minicomputer and then downloaded and modified to run on an ITT XTRA personal computer. Studies conducted to evaluate the efficiency of running the programs on a personal computer as compared with the minicomputer indicated that, with the proper combination of hardware and software options, the efficiency of using a personal computer exceeds that of a minicomputer.

White, P. R.↗
NASA NTRS1985

Flowmeter for Clear and Translucent Fluids

Transducer with only three moving parts senses flow of clear or translucent fluid. Displacement of diaphragm by force of flow detected electrooptically and displayed by panel meter or other device. Transducer used to measure flow of gasoline to automobile engine.

White, P. R.↗
NASA NTRS1981

Solar tracking system

A solar tracker for a solar collector is described in detail. The collector is angularly oriented by a motor wherein the outputs of two side-by-side photodetectors are discriminated as to three ranges: a first corresponding to a low light or darkness condition; a second corresponding to light intensity lying in an intermediate range; and a third corresponding to light above an intermediate range, direct sunlight. The first output drives the motor to a selected maximum easterly angular position; the second enables the motor to be driven westerly at the Earth rotational rate; and the third output, the separate outputs of the two photodetectors, differentially controls the direction of rotation of the motor to effect actual tracking of the Sun.

White, P. R.↗
NASA NTRS1980

Computer-aided design of curved surfaces with automatic model generation

The design and visualization of three-dimensional objects with curved surfaces have always been difficult. The paper given below describes a computer system which facilitates both the design and visualization of such surfaces. The system enhances the design of these surfaces by virtue of various interactive techniques coupled with the application of B-Spline theory. Visualization is facilitated by including a specially built model-making machine which produces three-dimensional foam models. Thus, the system permits the designer to produce an inexpensive model of the object which is suitable for evaluation and presentation.

Staley, S. M.↗
NASA NTRS1979

Sun tracker for clear or cloudy weather

Sun tracker orients solar collector so that they absorb maximum possible sunlight without being fooled by bright clouds, holes in cloud cover, or other atmospheric conditions. Tracker follows sun within 0.25 deg arc and is accurate within + or - 5 deg when sun is hidden.

Scott, D. R.↗
NASA NTRS1979

Solar tracking control system Sun Chaser

The solar tracking control system (Sun Chaser) is believed to be an improved method of tracking the Sun in all types of weather conditions. The Sun Chaser will follow the Sun from east to west in clear or cloudy weather, and reset itself to the east position after sundown in readiness for the next sunrise. A description of the Sun Chaser hardware and its operation together with results is presented.

Scott, D. R.↗
NASA NTRS1978

Solar tracking control system Sun Chaser

The solar tracking control system, Sun Chaser, a method of tracking the Sun in all types of weather conditions is described. The Sun Chaser follows the Sun from east to west in clear or cloudy weather, and resets itself to the east position after sundown in readiness for the next sunrise.

Scott, D. R.↗
NASA NTRS1972

Remote control and navigation tests for application to long-range lunar surface exploration.

A vehicle system has been built and tested to investigate some of the unknown factors with regard to the operation of a remotely controlled vehicle on the surface of the moon. A general vehicle system description is presented, giving attention to the wheel drive subsystem, the steering subsystem, the power system, the control console, the command subsystem, the television subsystem, the telemetry subsystem, and the navigation subsystem. The remote control driving station consists of the antenna system, the video display system, the instrument and control panel, the data panel, and the steering and throttle controls. Initial tests with the vehicle and the remote driving station were conducted in March and April 1971.

Mastin, W. C.↗