Engineering topics

White, N. H.

Publications and source records attributed to White, N. H..

9 records

NASA NTRS1997

Estimating Logistics Support of Reusable Launch Vehicles During Conceptual Design

Methods exist to define the logistics support requirements for new aircraft concepts but are not directly applicable to new launch vehicle concepts. In order to define the support requirements and to discriminate among new technologies and processing choices for these systems, NASA Langley Research Center (LaRC) is developing new analysis methods. This paper describes several methods under development, gives their current status, and discusses the benefits and limitations associated with their use.

Morris, W. D.↗

NASA NTRS1996

A Framework for the Optimization of Discrete-Event Simulation Models

With the growing use of computer modeling and simulation, in all aspects of engineering, the scope of traditional optimization has to be extended to include simulation models. Some unique aspects have to be addressed while optimizing via stochastic simulation models. The optimization procedure has to explicitly account for the randomness inherent in the stochastic measures predicted by the model. This paper outlines a general purpose framework for optimization of terminating discrete-event simulation models. The methodology combines a chance constraint approach for problem formulation, together with standard statistical estimation and analyses techniques. The applicability of the optimization framework is illustrated by minimizing the operation and support resources of a launch vehicle, through a simulation model.

Joshi, B. D.↗

NASA NTRS1996

Analysis of Shuttle Orbiter Reliability and Maintainability Data for Conceptual Studies

In order to provide a basis for estimating the expected support required of new systems during their conceptual design phase, Langley Research Center has recently collected Shuttle Orbiter reliability and maintainability data from the various data base sources at Kennedy Space Center. This information was analyzed to provide benchmarks, trends, and distributions to aid in the analysis of new designs. This paper presents a summation of those results and an initial interpretation of the findings.

Morris, W. D.↗

NASA NTRS1995

Defining Support Requirements During Conceptual Design of Reusable Launch Vehicles

Current methods for defining the operational support requirements of new systems are data intensive and require significant design information. Methods are being developed to aid in the analysis process of defining support requirements for new launch vehicles during their conceptual design phase that work with the level of information available during this phase. These methods will provide support assessments based on the vehicle design and the operating scenarios. The results can be used both to define expected support requirements for new launch vehicle designs and to help evaluate the benefits of using new technologies. This paper describes the models, their current status, and provides examples of their use.

Morris, W. D.↗

NASA NTRS1984

Performance assessment of aero-assisted orbital transfer vehicles

Aero-assisted orbital transfer vehicles are analyzed. The aerodynamic characteristics over the flight profile and three- and six-degree-of-freedom performance analyses were determined. The important results, to date, are: (1) the aerodynamic preliminary analysis system, an interactive computer program, used to predict the aerodynamics (performance, stability, and control) for these vehicles; (2) the performance capability, e.g., maximum inclination change, maximum heating rate, and maximum sensed acceleration, can be determined using continuum aerodynamics only; (3) guidance schemes can be developed that allow for errors in atmospheric density prediction, mispredicted trim angle of attack, and off-nominal atmospheric interface conditions, even for vehicles with a low lift-to-drag ratio; and (4) multiple pass trajectories can be used to reduce the maximum heating rate.

Powell, R. W.↗

NASA NTRS1984

Impact of atmospheric uncertainties and viscous interaction effects on the performance of aeroassisted orbital transfer vehicles

Simulations of aerobraking trajectories of aeroassisted orbital transfer vehicles (AOTV's) returning from geosynchronous orbit were analyzed to examine the effects of high-altitude viscous interactions and off-nominal atmospheres on AOTV return weight, heating, and loads performance. Viscous interaction effects encountered at high altitudes had little detrimental effect on the return weight capabilities for AOTV's representing a range of lift/drag ratios. Most of the AOTV return weight increase over an all-propulsive OTV occurred for a low lift/drag ratio. Smaller increases in return weight were observed for higher lift/drag ratios, at the expense of significantly higher heating and aerodynamic loads. Off-nominal atmospheres based on Shuttle-derived data and multipliers on a U.S. Standard Atmosphere were considered. AOTV's intended for entry under standard atmospheric conditions either deorbited during the pass through the off-nominal atmospheres or missed the target phasing orbit by wide margins. The AOTV's could successfully negotiate these atmospheres when new bank-angle histories were implemented with little loss and sometimes with a gain in return weight.

Talay, T. A.↗

NASA NTRS1980

Measured and predicted shock shapes and aerodynamic coefficients for blunted cones at incidence in air at Mach 5.9

Experimental values of shock shapes (angles of attack of 0 deg and 10 deg) and static aerodynamic coefficients (angles of attack of -4 deg to 12 deg for sharp and spherically blunted cones having cone half angles of 30 deg, 45 deg, 60 deg, and 70 deg, and nose bluntness ratios of 0, 0.25, and 0.50 are presented. Shock shapes were measured at 0 deg angle of attack by using a flat faced cylinder (90 deg cone) and a hemispherically blunted cylinder (sphere). All tests were conducted in air at a free stream Mach number of 5.9 and a unit free stream Reynolds number of 2,800,000 per meter. Comparisons between measured values and predicted values were made by using several numerical and simple engineering methods.

Calloway, R. L.↗

NASA NTRS1979

Measured and predicted shock shapes and aerodynamic coefficients for blunted cones at incidence in helium at Mach 20.3

Experimental values of shock shapes (alpha = 0 degrees and 10 degrees) and static aerodynamic coefficients (alpha = -4 degrees to 12 degrees) for sharp and spherically blunted cones having cone half-angles of 30, 45, 60, and 70 degrees and nose bluntness ratios of 0, 0.25, and 0.50 are presented. Shock shapes were also measured at 0 degree angle of attack by using a flat-faced cylinder (90 degree cone) and a hemispherically blunted cylinder (sphere). All tests were conducted in helium (gamma = 5/3) at a free-stream Mach number of 20.3 and a unit free-stream Reynolds number of 22,400,000 per meter. Comparisons between measured values and predicted values were made by using several numerical and simple engineering methods.

Calloway, R. L.↗

NASA NTRS1972

Fatigue crack growth from a circular hole with and without high prior loading

Fatigue crack growth from a circular hole was investigated experimentally and analytically. An aluminum-alloy sheet specimen was cycled under a single level of loading with and without prior high loads. Tests showed that the crack propagation life was significantly longer when the high loads were applied initially. This longer life was attributed to compressive residual stresses produced near the hole by the initial high loads. The residual stresses near the hole were determined by an elastoplastic analysis and were then used to develop a stress-intensity solution for a crack growing through the residual stress field. This solution and a similar solution for the case of no prior loading were used to predict crack growth. The predicted crack growth agreed closely with the experimental values.

Crews, J. H., Jr.↗